lkml.org 
[lkml]   [2022]   [Jul]   [6]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 1/2] arch: arm64: qcom: sdm845-shift-axolotl: fix Bluetooth firmware loading


On 09/06/2022 13:47, Dmitry Baryshkov wrote:
> On Thu, 9 Jun 2022 at 12:54, Alexander Martinz <amartinz@shiftphones.com> wrote:
>>
>> From: Dylan Van Assche <me@dylanvanassche.be>
>>
>> Add hsuart0 alias, firmware name and prevent garbage data on Bluetooth UART lines
>
> hsuart aliases are not standard. Please use serialN alias instead.
>
>> on the SHIFT 6mq based on the Qualcomm SDM845 chip.
>> I discovered that these were missing by comparing the DTS with similar
>> devices such as the Oneplus 6/6T and Dragonboard 845c.
>>
>> Signed-of-by: Dylan Van Assche <me@dylanvanassche.be>
>> Tested-by: Alexander Martinz <amartinz@shiftphones.com>
>> ---
>> .../boot/dts/qcom/sdm845-shift-axolotl.dts | 33 +++++++++++++++++++
>> 1 file changed, 33 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/qcom/sdm845-shift-axolotl.dts b/arch/arm64/boot/dts/qcom/sdm845-shift-axolotl.dts
>> index 103cc40816fd..fa72f23ef0c2 100644
>> --- a/arch/arm64/boot/dts/qcom/sdm845-shift-axolotl.dts
>> +++ b/arch/arm64/boot/dts/qcom/sdm845-shift-axolotl.dts
>> @@ -20,6 +20,7 @@ / {
>>
>> aliases {
>> display0 = &framebuffer0;
>> + hsuart0 = &uart6;
>> serial0 = &uart9;
>> };
>>
>> @@ -529,6 +530,32 @@ volume_down_resin: resin {
>> };
>> };
>>
>> +/*
>> + * Prevent garbage data on bluetooth UART lines
>> + */
>> +&qup_uart6_default {
>> + pinmux {
>> + pins = "gpio45", "gpio46", "gpio47", "gpio48";
>> + function = "qup6";
>> + };
>
> This chunk should probably go into sdm845.dtsi. I'd suggest either
> adding a separate qup_uart6_4pin or just making qup_uart6_default the
> 4-pin UART.
This sounds good
>
>> +
>> + cts {
>> + pins = "gpio45";
>
> Then the label and 'pins' can go into the dtsi, while keeping just the
> bias and drive-strength in the platform dtsi.
>
>> + bias-pull-down;
>> + };
>> +
>> + rts-tx {
>> + pins = "gpio46", "gpio47";
>> + drive-strength = <2>;
>> + bias-disable;
>> + };
>> +
>> + rx {
>> + pins = "gpio48";
>> + bias-pull-up;
>> + };
>> +};
>> +
>> &qup_uart9_default {
>> pinconf-rx {
>> pins = "gpio5";
>> @@ -667,6 +694,12 @@ &uart6 {
>> bluetooth {
>> compatible = "qcom,wcn3990-bt";
>>
>> + /*
>> + * This path is relative to the qca/
>> + * subdir under lib/firmware.
>> + */
>> + firmware-name = "axolotl/crnv21.bin";
>
> Do you know what is the difference between axolotl's bin and the regular one?
Just checked in a hex editor and there are some differences. This firmware is
signed on most devices but given the SHIFT6mq is secureboot off we could in
theory use upstream firmware here - if it works. This particular device has some
very broken wifi firmware - we have to use the firmware from the OnePlus 6 to
get wifi to work at all...
>
>> +
>> vddio-supply = <&vreg_s4a_1p8>;
>> vddxo-supply = <&vreg_l7a_1p8>;
>> vddrf-supply = <&vreg_l17a_1p3>;
>
> --
> With best wishes
> Dmitry

--
Kind Regards,
Caleb

\
 
 \ /
  Last update: 2022-07-06 20:51    [W:0.078 / U:0.192 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site