lkml.org 
[lkml]   [2022]   [Jul]   [5]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH] dt-bindings: pinctrl: mt8195: Add and use drive-strength-microamp
On Thu, Jun 30, 2022 at 03:15:43PM +0200, AngeloGioacchino Del Regno wrote:
> As was already done for MT8192 in commit b52e695324bb ("dt-bindings:
> pinctrl: mt8192: Add drive-strength-microamp"), replace the custom
> mediatek,drive-strength-adv property with the standardized pinconf
> 'drive-strength-microamp' one.
>
> Similarly to the mt8192 counterpart, there's no user of property
> 'mediatek,drive-strength-adv', hence removing it is safe.
>
> Fixes: 69c3d58dc187 ("dt-bindings: pinctrl: mt8195: Add mediatek,drive-strength-adv property")
> Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>

Ideally we'd prevent using drive-strength-microamp together with drive-strength,
like I intended to do on v2 of the patch [1], just as an extra sanity check. But
that could be added later on top, so

Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>

Thanks,
Nícolas

[1] https://lore.kernel.org/all/20220531221954.160036-2-nfraprado@collabora.com/

> ---
> .../bindings/pinctrl/pinctrl-mt8195.yaml | 27 ++-----------------
> 1 file changed, 2 insertions(+), 25 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8195.yaml b/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8195.yaml
> index b0fea44403e7..85e96a5e1708 100644
> --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8195.yaml
> +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8195.yaml
> @@ -100,31 +100,8 @@ patternProperties:
> drive-strength:
> enum: [2, 4, 6, 8, 10, 12, 14, 16]
>
> - mediatek,drive-strength-adv:
> - description: |
> - Describe the specific driving setup property.
> - For I2C pins, the existing generic driving setup can only support
> - 2/4/6/8/10/12/14/16mA driving. But in specific driving setup, they
> - can support 0.125/0.25/0.5/1mA adjustment. If we enable specific
> - driving setup, the existing generic setup will be disabled.
> - The specific driving setup is controlled by E1E0EN.
> - When E1=0/E0=0, the strength is 0.125mA.
> - When E1=0/E0=1, the strength is 0.25mA.
> - When E1=1/E0=0, the strength is 0.5mA.
> - When E1=1/E0=1, the strength is 1mA.
> - EN is used to enable or disable the specific driving setup.
> - Valid arguments are described as below:
> - 0: (E1, E0, EN) = (0, 0, 0)
> - 1: (E1, E0, EN) = (0, 0, 1)
> - 2: (E1, E0, EN) = (0, 1, 0)
> - 3: (E1, E0, EN) = (0, 1, 1)
> - 4: (E1, E0, EN) = (1, 0, 0)
> - 5: (E1, E0, EN) = (1, 0, 1)
> - 6: (E1, E0, EN) = (1, 1, 0)
> - 7: (E1, E0, EN) = (1, 1, 1)
> - So the valid arguments are from 0 to 7.
> - $ref: /schemas/types.yaml#/definitions/uint32
> - enum: [0, 1, 2, 3, 4, 5, 6, 7]
> + drive-strength-microamp:
> + enum: [125, 250, 500, 1000]
>
> bias-pull-down:
> oneOf:
> --
> 2.35.1
>

\
 
 \ /
  Last update: 2022-07-05 18:51    [W:1.177 / U:0.260 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site