lkml.org 
[lkml]   [2022]   [Jul]   [31]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v4 5/9] iio: adc: mcp3911: add support for buffers
On Fri, 22 Jul 2022 15:07:22 +0200
Marcus Folkesson <marcus.folkesson@gmail.com> wrote:

> Add support for buffers to make the driver fit for more usecases.
>
> Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>

Assuming the Kconfig change from previous patch is pulled into this one...

A few questions / comments inline.

Thanks,

Jonathan

> ---
> drivers/iio/adc/mcp3911.c | 96 ++++++++++++++++++++++++++++++++++++---
> 1 file changed, 89 insertions(+), 7 deletions(-)
>
> diff --git a/drivers/iio/adc/mcp3911.c b/drivers/iio/adc/mcp3911.c
> index 00dadb1761dc..96c0a2a50c7c 100644
> --- a/drivers/iio/adc/mcp3911.c
> +++ b/drivers/iio/adc/mcp3911.c
> @@ -5,15 +5,22 @@
> * Copyright (C) 2018 Marcus Folkesson <marcus.folkesson@gmail.com>
> * Copyright (C) 2018 Kent Gustavsson <kent@minoris.se>
> */
> +#include <linux/bitfield.h>
> +#include <linux/bits.h>
> #include <linux/clk.h>
> #include <linux/delay.h>
> #include <linux/err.h>
> #include <linux/iio/iio.h>
> +#include <linux/iio/buffer.h>
> +#include <linux/iio/triggered_buffer.h>
> +#include <linux/iio/trigger_consumer.h>
> +#include <linux/iio/trigger.h>
> #include <linux/module.h>
> #include <linux/mod_devicetable.h>
> #include <linux/property.h>
> #include <linux/regulator/consumer.h>
> #include <linux/spi/spi.h>

Line break here to separate the 'chunks' of includes.

> +#include <asm/unaligned.h>
>
> #define MCP3911_REG_CHANNEL0 0x00
> #define MCP3911_REG_CHANNEL1 0x03
> @@ -22,6 +29,7 @@
> #define MCP3911_REG_GAIN 0x09
>
> #define MCP3911_REG_STATUSCOM 0x0a
> +#define MCP3911_STATUSCOM_READ GENMASK(7, 6)
> #define MCP3911_STATUSCOM_CH1_24WIDTH BIT(4)
> #define MCP3911_STATUSCOM_CH0_24WIDTH BIT(3)
> #define MCP3911_STATUSCOM_EN_OFFCAL BIT(2)
> @@ -54,6 +62,13 @@ struct mcp3911 {
> struct regulator *vref;
> struct clk *clki;
> u32 dev_addr;
> + struct {
> + u32 channels[MCP3911_NUM_CHANNELS];
> + s64 ts __aligned(8);
> + } scan;
> +
> + u8 tx_buf[MCP3911_NUM_CHANNELS * 3] __aligned(IIO_DMA_MINALIGN);
> + u8 rx_buf[MCP3911_NUM_CHANNELS * 3];
> };
>
> static int mcp3911_read(struct mcp3911 *adc, u8 reg, u32 *val, u8 len)
> @@ -196,16 +211,63 @@ static int mcp3911_write_raw(struct iio_dev *indio_dev,
> .type = IIO_VOLTAGE, \
> .indexed = 1, \
> .channel = idx, \
> + .scan_index = idx, \
> .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | \
> BIT(IIO_CHAN_INFO_OFFSET) | \
> BIT(IIO_CHAN_INFO_SCALE), \
> + .scan_type = { \
> + .sign = 's', \
> + .realbits = 24, \
> + .storagebits = 32, \
> + .endianness = IIO_BE, \
> + }, \
> }
>
> static const struct iio_chan_spec mcp3911_channels[] = {
> MCP3911_CHAN(0),
> MCP3911_CHAN(1),
> + IIO_CHAN_SOFT_TIMESTAMP(2),
> };
>
> +static irqreturn_t mcp3911_trigger_handler(int irq, void *p)
> +{
> + struct iio_poll_func *pf = p;
> + struct iio_dev *indio_dev = pf->indio_dev;
> + struct mcp3911 *adc = iio_priv(indio_dev);
> + struct spi_transfer xfer = {
> + .tx_buf = adc->tx_buf,
> + .rx_buf = adc->rx_buf,
> + .len = sizeof(adc->rx_buf),
> + };
> + int scan_index;
> + int i = 0;
> + int ret;
> +
> + mutex_lock(&adc->lock);
> + adc->tx_buf[0] = MCP3911_REG_READ(MCP3911_CHANNEL(0), adc->dev_addr);
> + ret = spi_sync_transfer(adc->spi, &xfer, 1);
> + if (ret < 0) {
> + dev_warn(&adc->spi->dev,
> + "failed to get conversion data\n");
> + goto out;
> + }
> +
> + for_each_set_bit(scan_index, indio_dev->active_scan_mask,
> + indio_dev->masklength) {
> + const struct iio_chan_spec *scan_chan = &indio_dev->channels[scan_index];
> +
> + adc->scan.channels[i] = get_unaligned_be24(&adc->rx_buf[scan_chan->channel * 3]);

This has me a little curious. It seems to be potentially reading from byte 0 which in the spi
transfer is at the same time as the tx that tells the device what the command is. I'd expect
it to be one byte later. Easiest way to do that being to have two transfers (though you could
just add to the offset). I might be misremembering how the spi_transfer stuff works though.
Been a while since I hacked anything SPI based...

> + i++;
> + }
> + iio_push_to_buffers_with_timestamp(indio_dev, &adc->scan,
> + iio_get_time_ns(indio_dev));
> +out:
> + mutex_unlock(&adc->lock);
> + iio_trigger_notify_done(indio_dev->trig);
> +
> + return IRQ_HANDLED;
> +}
> +
> static const struct iio_info mcp3911_info = {
> .read_raw = mcp3911_read_raw,
> .write_raw = mcp3911_write_raw,
> @@ -214,7 +276,7 @@ static const struct iio_info mcp3911_info = {
> static int mcp3911_config(struct mcp3911 *adc)
> {
> struct device *dev = &adc->spi->dev;
> - u32 configreg;
> + u32 regval;
> int ret;
>
> ret = device_property_read_u32(dev, "microchip,device-addr", &adc->dev_addr);
> @@ -233,29 +295,43 @@ static int mcp3911_config(struct mcp3911 *adc)
> }
> dev_dbg(&adc->spi->dev, "use device address %i\n", adc->dev_addr);
>
> - ret = mcp3911_read(adc, MCP3911_REG_CONFIG, &configreg, 2);
> + ret = mcp3911_read(adc, MCP3911_REG_CONFIG, &regval, 2);

If I was being fussy I'd ask you to pull the refactoring in here out as a precusor
patch to simplify reviewing the new stuff a little. However it's fairly minor
so I'll let that go this time.

> if (ret)
> return ret;
>
> + regval &= ~MCP3911_CONFIG_VREFEXT;
> if (adc->vref) {
> dev_dbg(&adc->spi->dev, "use external voltage reference\n");
> - configreg |= MCP3911_CONFIG_VREFEXT;
> + regval |= FIELD_PREP(MCP3911_CONFIG_VREFEXT, 1);
> } else {
> dev_dbg(&adc->spi->dev,
> "use internal voltage reference (1.2V)\n");
> - configreg &= ~MCP3911_CONFIG_VREFEXT;
> + regval |= FIELD_PREP(MCP3911_CONFIG_VREFEXT, 0);
> }
>
> + regval &= ~MCP3911_CONFIG_CLKEXT;
> if (adc->clki) {
> dev_dbg(&adc->spi->dev, "use external clock as clocksource\n");
> - configreg |= MCP3911_CONFIG_CLKEXT;
> + regval |= FIELD_PREP(MCP3911_CONFIG_CLKEXT, 1);
> } else {
> dev_dbg(&adc->spi->dev,
> "use crystal oscillator as clocksource\n");
> - configreg &= ~MCP3911_CONFIG_CLKEXT;
> + regval |= FIELD_PREP(MCP3911_CONFIG_CLKEXT, 0);
> }
>
> - return mcp3911_write(adc, MCP3911_REG_CONFIG, configreg, 2);
> + ret = mcp3911_write(adc, MCP3911_REG_CONFIG, regval, 2);
> + if (ret)
> + return ret;
> +
> + ret = mcp3911_read(adc, MCP3911_REG_STATUSCOM, &regval, 2);
> + if (ret)
> + return ret;
> +
> + /* Address counter incremented, cycle through register types */
> + regval &= ~MCP3911_STATUSCOM_READ;
> + regval |= FIELD_PREP(MCP3911_STATUSCOM_READ, 0x02);
> +
> + return mcp3911_write(adc, MCP3911_REG_STATUSCOM, regval, 2);
> }
>


\
 
 \ /
  Last update: 2022-07-31 18:42    [W:0.127 / U:1.028 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site