lkml.org 
[lkml]   [2022]   [Jul]   [28]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v3 6/6] tracing/user_events: Update ABI documentation to align to bits vs bytes
Date
Update the documentation to reflect the new ABI requirements and how to
use the byte index with the mask properly to check event status.

Signed-off-by: Beau Belgrave <beaub@linux.microsoft.com>
---
Documentation/trace/user_events.rst | 86 +++++++++++++++++++----------
1 file changed, 58 insertions(+), 28 deletions(-)

diff --git a/Documentation/trace/user_events.rst b/Documentation/trace/user_events.rst
index c180936f49fc..9f181f342a70 100644
--- a/Documentation/trace/user_events.rst
+++ b/Documentation/trace/user_events.rst
@@ -20,14 +20,14 @@ dynamic_events is the same as the ioctl with the u: prefix applied.

Typically programs will register a set of events that they wish to expose to
tools that can read trace_events (such as ftrace and perf). The registration
-process gives back two ints to the program for each event. The first int is the
-status index. This index describes which byte in the
+process gives back two ints to the program for each event. The first int is
+the status bit. This describes which bit in little-endian format in the
/sys/kernel/debug/tracing/user_events_status file represents this event. The
-second int is the write index. This index describes the data when a write() or
+second int is the write index which describes the data when a write() or
writev() is called on the /sys/kernel/debug/tracing/user_events_data file.

-The structures referenced in this document are contained with the
-/include/uap/linux/user_events.h file in the source tree.
+The structures referenced in this document are contained within the
+/include/uapi/linux/user_events.h file in the source tree.

**NOTE:** *Both user_events_status and user_events_data are under the tracefs
filesystem and may be mounted at different paths than above.*
@@ -38,18 +38,18 @@ Registering within a user process is done via ioctl() out to the
/sys/kernel/debug/tracing/user_events_data file. The command to issue is
DIAG_IOCSREG.

-This command takes a struct user_reg as an argument::
+This command takes a packed struct user_reg as an argument::

struct user_reg {
u32 size;
u64 name_args;
- u32 status_index;
+ u32 status_bit;
u32 write_index;
};

The struct user_reg requires two inputs, the first is the size of the structure
to ensure forward and backward compatibility. The second is the command string
-to issue for registering. Upon success two outputs are set, the status index
+to issue for registering. Upon success two outputs are set, the status bit
and the write index.

User based events show up under tracefs like any other event under the
@@ -111,15 +111,56 @@ in realtime. This allows user programs to only incur the cost of the write() or
writev() calls when something is actively attached to the event.

User programs call mmap() on /sys/kernel/debug/tracing/user_events_status to
-check the status for each event that is registered. The byte to check in the
-file is given back after the register ioctl() via user_reg.status_index.
+check the status for each event that is registered. The bit to check in the
+file is given back after the register ioctl() via user_reg.status_bit. The bit
+is always in little-endian format. Programs can check if the bit is set either
+using a byte-wise index with a mask or a long-wise index with a little-endian
+mask.
+
Currently the size of user_events_status is a single page, however, custom
kernel configurations can change this size to allow more user based events. In
all cases the size of the file is a multiple of a page size.

-For example, if the register ioctl() gives back a status_index of 3 you would
-check byte 3 of the returned mmap data to see if anything is attached to that
-event.
+For example, if the register ioctl() gives back a status_bit of 3 you would
+check byte 0 (3 / 8) of the returned mmap data and then AND the result with 8
+(1 << (3 % 8)) to see if anything is attached to that event.
+
+A byte-wise index check is performed as follows::
+
+ int index, mask;
+ char *status_page;
+
+ index = status_bit / 8;
+ mask = 1 << (status_bit % 8);
+
+ ...
+
+ if (status_page[index] & mask) {
+ /* Enabled */
+ }
+
+A long-wise index check is performed as follows::
+
+ #include <asm/bitsperlong.h>
+ #include <endian.h>
+
+ #if __BITS_PER_LONG == 64
+ #define endian_swap(x) htole64(x)
+ #else
+ #define endian_swap(x) htole32(x)
+ #endif
+
+ long index, mask, *status_page;
+
+ index = status_bit / __BITS_PER_LONG;
+ mask = 1L << (status_bit % __BITS_PER_LONG);
+ mask = endian_swap(mask);
+
+ ...
+
+ if (status_page[index] & mask) {
+ /* Enabled */
+ }

Administrators can easily check the status of all registered events by reading
the user_events_status file directly via a terminal. The output is as follows::
@@ -137,7 +178,7 @@ For example, on a system that has a single event the output looks like this::

Active: 1
Busy: 0
- Max: 4096
+ Max: 32768

If a user enables the user event via ftrace, the output would change to this::

@@ -145,21 +186,10 @@ If a user enables the user event via ftrace, the output would change to this::

Active: 1
Busy: 1
- Max: 4096
-
-**NOTE:** *A status index of 0 will never be returned. This allows user
-programs to have an index that can be used on error cases.*
-
-Status Bits
-^^^^^^^^^^^
-The byte being checked will be non-zero if anything is attached. Programs can
-check specific bits in the byte to see what mechanism has been attached.
-
-The following values are defined to aid in checking what has been attached:
-
-**EVENT_STATUS_FTRACE** - Bit set if ftrace has been attached (Bit 0).
+ Max: 32768

-**EVENT_STATUS_PERF** - Bit set if perf has been attached (Bit 1).
+**NOTE:** *A status bit of 0 will never be returned. This allows user programs
+to have a bit that can be used on error cases.*

Writing Data
------------
--
2.25.1
\
 
 \ /
  Last update: 2022-07-29 01:34    [W:0.044 / U:0.016 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site