lkml.org 
[lkml]   [2022]   [Jul]   [2]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
SubjectRe: [PATCH v8 3/5] mtd: Add support for HyperBus memory devices
From
Hi Geert,

On 6/27/2022 8:58 PM, Geert Uytterhoeven wrote:
> Hi Vignesh,
>
> On Tue, Jun 25, 2019 at 10:00 AM Vignesh Raghavendra <vigneshr@ti.com> wrote:
>> Cypress' HyperBus is Low Signal Count, High Performance Double Data Rate
>> Bus interface between a host system master and one or more slave
>> interfaces. HyperBus is used to connect microprocessor, microcontroller,
>> or ASIC devices with random access NOR flash memory (called HyperFlash)
>> or self refresh DRAM (called HyperRAM).
>>
>> Its a 8-bit data bus (DQ[7:0]) with Read-Write Data Strobe (RWDS)
>> signal and either Single-ended clock(3.0V parts) or Differential clock
>> (1.8V parts). It uses ChipSelect lines to select b/w multiple slaves.
>> At bus level, it follows a separate protocol described in HyperBus
>> specification[1].
>>
>> HyperFlash follows CFI AMD/Fujitsu Extended Command Set (0x0002) similar
>> to that of existing parallel NORs. Since HyperBus is x8 DDR bus,
>> its equivalent to x16 parallel NOR flash with respect to bits per clock
>> cycle. But HyperBus operates at >166MHz frequencies.
>> HyperRAM provides direct random read/write access to flash memory
>> array.
>>
>> But, HyperBus memory controllers seem to abstract implementation details
>> and expose a simple MMIO interface to access connected flash.
>>
>> Add support for registering HyperFlash devices with MTD framework. MTD
>> maps framework along with CFI chip support framework are used to support
>> communicating with flash.
>>
>> Framework is modelled along the lines of spi-nor framework. HyperBus
>> memory controller (HBMC) drivers calls hyperbus_register_device() to
>> register a single HyperFlash device. HyperFlash core parses MMIO access
>> information from DT, sets up the map_info struct, probes CFI flash and
>> registers it with MTD framework.
>>
>> Some HBMC masters need calibration/training sequence[3] to be carried
>> out, in order for DLL inside the controller to lock, by reading a known
>> string/pattern. This is done by repeatedly reading CFI Query
>> Identification String. Calibration needs to be done before trying to detect
>> flash as part of CFI flash probe.
>>
>> HyperRAM is not supported at the moment.
>
> Thanks for your patch, which is now commit dcc7d3446a0fa19b ("mtd:
> Add support for HyperBus memory devices") in v5.3.
>
>> HyperBus specification can be found at[1]
>> HyperFlash datasheet can be found at[2]
>>
>> [1] https://www.cypress.com/file/213356/download
>> [2] https://www.cypress.com/file/213346/download
>> [3] http://www.ti.com/lit/ug/spruid7b/spruid7b.pdf
>> Table 12-5741. HyperFlash Access Sequence
>
> The last link no longer works. Do you have a replacement?

Looks like I used a link point to specific version instead of top level
redirector link. Please use:

https://www.ti.com/lit/pdf/spruid7

Regards
Vignesh

\
 
 \ /
  Last update: 2022-07-02 19:12    [W:0.482 / U:0.208 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site