lkml.org 
[lkml]   [2022]   [Jul]   [18]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
SubjectRe: [PATCH 2/4] arm64: dts: qcom: add sdm845-google-blueline (Pixel 3)
From
On 19/07/2022 00:30, Caleb Connolly wrote:
> From: Amit Pundir <amit.pundir@linaro.org>
>
> This adds an initial dts for the Blueline (Pixel 3). Supported
> functionality includes display, Debug UART, UFS, USB-C (peripheral), WiFi,
> Bluetooth and modem.
>
> Bootloader compatible board and msm IDs are needed for the kernel to boot
> with Pixel3 bootloader, so those are added.
>
> GPIOs 0 through 3 and 81 through 84 are configured to not be accessible
> from the application CPUs, so we mark them as reserved to allow the Pixel 3
> to boot.
>
> The reserved-memory locations where obtained from downstream using
> kernel logs:
> https://gist.github.com/calebccff/090d10bfac3cb9e9bd98dda30b054c96
>
> The rmtfs region is allocated with UIO, making it technically "dynamic".
> It's address and size can be read from sysfs:
>
> blueline:/ # cat /sys/class/uio/uio0/name
> rmtfs
> at /sys/class/uio/uio0/maps/map0/addr
> 0x00000000f2701000
> blueline:/ # cat /sys/class/uio/uio0/maps/map0/size
> 0x0000000000200000
>
> Like the OnePlus 6, it needs 1kB reserved on either side of the rmtfs
> memory to workaround some XPU bug which would otherwise cause erroneous
> XPU violations when accessing the rmtfs_mem region.
>
> For wifi, the pixel 3 reports a board-id of 0xFF, and downstream
> only includes a single bdwlan file. The qcom,ath10k-calibration-variant
> property is set to ensure that the correct calibration data is used.
>
> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
> [AmitP: Cherry-picked and refactored from Bjorn's db845c dts
> ("arm64: dts: qcom: Add Dragonboard 845c") https://lkml.org/lkml/2019/6/6/7]
> Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
> [sumits: merged commits to add board and msm ids, gpio range reservation,
> ufs device-reset gpio and adaptation to v5.5+ changes]
> Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
> [vinod: Add display nodes]
> Signed-off-by: Vinod Koul <vkoul@kernel.org>
> [caleb: remove db845c bits, cleanup, add reserved-memory for modem/wifi]
> Signed-off-by: Caleb Connolly <caleb@connolly.tech>

Thanks for your patch, few minor items to improve.

> ---
> arch/arm64/boot/dts/qcom/Makefile | 1 +
> .../boot/dts/qcom/sdm845-google-blueline.dts | 652 ++++++++++++++++++
> 2 files changed, 653 insertions(+)
> create mode 100644 arch/arm64/boot/dts/qcom/sdm845-google-blueline.dts
>
> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
> index 2f8aec2cc6db..c151e17e6eb7 100644
> --- a/arch/arm64/boot/dts/qcom/Makefile
> +++ b/arch/arm64/boot/dts/qcom/Makefile
> @@ -100,6 +100,7 @@ dtb-$(CONFIG_ARCH_QCOM) += sdm845-cheza-r1.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sdm845-cheza-r2.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sdm845-cheza-r3.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sdm845-db845c.dtb
> +dtb-$(CONFIG_ARCH_QCOM) += sdm845-google-blueline.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sdm845-mtp.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sdm845-oneplus-enchilada.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sdm845-oneplus-fajita.dtb
> diff --git a/arch/arm64/boot/dts/qcom/sdm845-google-blueline.dts b/arch/arm64/boot/dts/qcom/sdm845-google-blueline.dts
> new file mode 100644
> index 000000000000..dec979ad9209
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/sdm845-google-blueline.dts
> @@ -0,0 +1,652 @@
> +// SPDX-License-Identifier: GPL-2.0
> +
> +/dts-v1/;
> +
> +#include <dt-bindings/dma/qcom-gpi.h>
> +#include <dt-bindings/input/linux-event-codes.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
> +#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
> +
> +#include "sdm845.dtsi"
> +#include "pm8998.dtsi"
> +#include "pmi8998.dtsi"
> +
> +/delete-node/ &mpss_region;
> +/delete-node/ &venus_mem;
> +/delete-node/ &cdsp_mem;
> +/delete-node/ &mba_region;
> +/delete-node/ &slpi_mem;
> +/delete-node/ &spss_mem;
> +/delete-node/ &rmtfs_mem;
> +
> +/ {
> + model = "Google Pixel 3";
> + compatible = "google,blueline", "qcom,sdm845";
> + qcom,board-id = <0x00021505 0>;
> + qcom,msm-id = <321 0x20001>;
> +
> + aliases {
> + serial0 = &uart9;
> + serial1 = &uart6;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + volume-keys {
> + compatible = "gpio-keys";
> + label = "Volume keys";
> + autorepeat;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&volume_up_gpio>;
> +
> + vol-up {
> + label = "Volume Up";
> + linux,code = <KEY_VOLUMEUP>;
> + gpios = <&pm8998_gpio 6 GPIO_ACTIVE_LOW>;
> + debounce-interval = <15>;
> + };
> + };
> +
> + reserved-memory {
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;

These properties are already part of the sdm845.dtsi, so no need to have
them here.

> +
> + mpss_region: memory@8e000000 {
> + reg = <0 0x8e000000 0 0x9800000>;
> + no-map;
> + };
> +
> + venus_mem: venus@97800000 {
> + reg = <0 0x97800000 0 0x500000>;
> + no-map;
> + };
> +
> + cdsp_mem: cdsp-mem@97D00000 {
> + reg = <0 0x97D00000 0 0x800000>;
> + no-map;
> + };
> +
> + mba_region: mba@98500000 {
> + reg = <0 0x98500000 0 0x200000>;
> + no-map;
> + };
> +
> + slpi_mem: slpi@98700000 {
> + reg = <0 0x98700000 0 0x1400000>;
> + no-map;
> + };
> +
> + spss_mem: spss@99B00000 {
> + reg = <0 0x99B00000 0 0x100000>;
> + no-map;
> + };
> +
> + /* rmtfs lower guard */
> + memory@f2700000 {
> + reg = <0 0xf2700000 0 0x1000>;
> + no-map;
> + };
> +
> + rmtfs_mem: memory@f2701000 {
> + compatible = "qcom,rmtfs-mem";
> + reg = <0 0xf2701000 0 0x200000>;
> + no-map;
> +
> + qcom,client-id = <1>;
> + qcom,vmid = <15>;
> + };
> +
> + /* rmtfs upper guard */
> + memory@f2901000 {
> + reg = <0 0xf2901000 0 0x1000>;
> + no-map;
> + };
> + };
> +
> + vph_pwr: vph-pwr-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "vph_pwr";
> + regulator-min-microvolt = <3700000>;
> + regulator-max-microvolt = <3700000>;
> + };
> +
> + vreg_s4a_1p8: vreg-s4a-1p8 {
> + compatible = "regulator-fixed";
> + regulator-name = "vreg_s4a_1p8";
> +
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + regulator-boot-on;
> +
> + vin-supply = <&vph_pwr>;
> + };
> +};
> +
> +&adsp_pas {
> + status = "okay";
> +
> + firmware-name = "qcom/sdm845/pixel3/adsp.mbn";

What about using "qcom/sdm845/blueline/adsp.mbn" instead?

Bjorn, Amit?

> +};
> +
> +&apps_rsc {
> + pm8998-rpmh-regulators {
> + compatible = "qcom,pm8998-rpmh-regulators";
> + qcom,pmic-id = "a";
> + vdd-s1-supply = <&vph_pwr>;
> + vdd-s2-supply = <&vph_pwr>;
> + vdd-s3-supply = <&vph_pwr>;
> + vdd-s4-supply = <&vph_pwr>;
> + vdd-s5-supply = <&vph_pwr>;
> + vdd-s6-supply = <&vph_pwr>;
> + vdd-s7-supply = <&vph_pwr>;
> + vdd-s8-supply = <&vph_pwr>;
> + vdd-s9-supply = <&vph_pwr>;
> + vdd-s10-supply = <&vph_pwr>;
> + vdd-s11-supply = <&vph_pwr>;
> + vdd-s12-supply = <&vph_pwr>;
> + vdd-s13-supply = <&vph_pwr>;
> + vdd-l1-l27-supply = <&vreg_s7a_1p025>;
> + vdd-l2-l8-l17-supply = <&vreg_s3a_1p35>;
> + vdd-l3-l11-supply = <&vreg_s7a_1p025>;
> + vdd-l4-l5-supply = <&vreg_s7a_1p025>;
> + vdd-l6-supply = <&vph_pwr>;
> + vdd-l7-l12-l14-l15-supply = <&vreg_s5a_2p04>;
> + vdd-l9-supply = <&vreg_bob>;
> + vdd-l10-l23-l25-supply = <&vreg_bob>;
> + vdd-l13-l19-l21-supply = <&vreg_bob>;
> + vdd-l16-l28-supply = <&vreg_bob>;
> + vdd-l18-l22-supply = <&vreg_bob>;
> + vdd-l20-l24-supply = <&vreg_bob>;
> + vdd-l26-supply = <&vreg_s3a_1p35>;
> + vin-lvs-1-2-supply = <&vreg_s4a_1p8>;
> +
> + vreg_s3a_1p35: smps3 {
> + regulator-min-microvolt = <1352000>;
> + regulator-max-microvolt = <1352000>;
> + };
> +
> + vreg_s5a_2p04: smps5 {
> + regulator-min-microvolt = <1904000>;
> + regulator-max-microvolt = <2040000>;
> + };
> +
> + vreg_s7a_1p025: smps7 {
> + regulator-min-microvolt = <900000>;
> + regulator-max-microvolt = <1028000>;
> + };
> +
> + vdda_mipi_dsi0_pll:

Do we need this alias?

> + vreg_l1a_0p875: ldo1 {
> + regulator-min-microvolt = <880000>;
> + regulator-max-microvolt = <880000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-boot-on;
> + };
> +
> + vreg_l5a_0p8: ldo5 {
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <800000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l12a_1p8: ldo12 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l7a_1p8: ldo7 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l13a_2p95: ldo13 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <2960000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l14a_1p88: ldo14 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-boot-on;
> + /*
> + * We can't properly bring the panel back if it gets turned off
> + * so keep it's regulators always on for now.
> + */

Any idea, what is the issue here? Do you have the datasheet for the panel?

> + regulator-always-on;
> + };
> +
> + vreg_l17a_1p3: ldo17 {
> + regulator-min-microvolt = <1304000>;
> + regulator-max-microvolt = <1304000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l19a_3p3: ldo19 {
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3312000>;
> + qcom,init-voltage = <3300000>;
> + qcom,initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + /*
> + * The touchscreen needs this to be 3.3v, which is apparently
> + * quite close to the hardware limit for this LDO (3.312v)
> + * It must be kept in high power mode to prevent TS brownouts
> + */
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l20a_2p95: ldo20 {
> + regulator-min-microvolt = <2960000>;
> + regulator-max-microvolt = <2968000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l21a_2p95: ldo21 {
> + regulator-min-microvolt = <2960000>;
> + regulator-max-microvolt = <2968000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l24a_3p075: ldo24 {
> + regulator-min-microvolt = <3088000>;
> + regulator-max-microvolt = <3088000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l25a_3p3: ldo25 {
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3312000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vdda_mipi_dsi0_1p2:

Do we need this alias?

> + vreg_l26a_1p2: ldo26 {
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-boot-on;
> + };
> +
> + vreg_l28a_3p0: ldo28 {
> + regulator-min-microvolt = <2856000>;
> + regulator-max-microvolt = <3008000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-boot-on;
> + /*
> + * We can't properly bring the panel back if it gets turned off
> + * so keep it's regulators always on for now.
> + */
> + regulator-always-on;
> + };
> + };
> +
> + pmi8998-rpmh-regulators {
> + compatible = "qcom,pmi8998-rpmh-regulators";
> + qcom,pmic-id = "b";
> +
> + vdd-bob-supply = <&vph_pwr>;
> +
> + vreg_bob: bob {
> + regulator-min-microvolt = <3312000>;
> + regulator-max-microvolt = <3600000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
> + regulator-allow-bypass;
> + };
> + };
> +
> + pm8005-rpmh-regulators {
> + compatible = "qcom,pm8005-rpmh-regulators";
> + qcom,pmic-id = "c";
> +
> + vdd-s1-supply = <&vph_pwr>;
> + vdd-s2-supply = <&vph_pwr>;
> + vdd-s3-supply = <&vph_pwr>;
> + vdd-s4-supply = <&vph_pwr>;
> +
> + vreg_s3c_0p6: smps3 {
> + regulator-min-microvolt = <600000>;
> + regulator-max-microvolt = <600000>;
> + };
> + };
> +};
> +
> +&cdsp_pas {
> + status = "okay";
> + firmware-name = "qcom/sdm845/pixel3/cdsp.mbn";
> +};
> +
> +&dsi0 {
> + status = "okay";
> + vdda-supply = <&vdda_mipi_dsi0_1p2>;
> +
> + ports {
> + port@1 {
> + endpoint {
> + remote-endpoint = <&lg_sw43408_in_0>;
> + data-lanes = <0 1 2 3>;
> + };
> + };
> + };
> +
> + panel@0 {
> + compatible = "lg,sw43408";
> + reg = <0>;
> +
> + vddi-supply = <&vreg_l14a_1p88>;
> + vpnl-supply = <&vreg_l28a_3p0>;
> +
> + reset-gpios = <&tlmm 6 GPIO_ACTIVE_LOW>;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&panel_reset_pins &panel_te_pin &panel_pmgpio_pins>;
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> + lg_sw43408_in_0: endpoint {
> + remote-endpoint = <&dsi0_out>;
> + };
> + };
> + };
> + };
> +};
> +
> +&dsi0_out {
> + remote-endpoint = <&lg_sw43408_in_0>;
> + data-lanes = <0 1 2 3>;
> +};
> +
> +&dsi0_phy {
> + status = "okay";
> + vdds-supply = <&vdda_mipi_dsi0_pll>;
> +};
> +
> +&gcc {
> + protected-clocks = <GCC_QSPI_CORE_CLK>,
> + <GCC_QSPI_CORE_CLK_SRC>,
> + <GCC_QSPI_CNOC_PERIPH_AHB_CLK>;
> +};
> +
> +&gmu {
> + status = "okay";
> +};
> +
> +&gpi_dma0 {
> + status = "okay";
> +};
> +
> +&gpu {
> + status = "okay";
> +
> + zap-shader {
> + memory-region = <&gpu_mem>;
> + firmware-name = "qcom/sdm845/pixel3/a630_zap.mbn";
> + };
> +};
> +
> +&ipa {
> + status = "okay";
> +
> + firmware-name = "qcom/sdm845/pixel3/ipa_fws.mbn";
> +};
> +
> +&mss_pil {
> + status = "okay";
> + firmware-name = "qcom/sdm845/pixel3/mba.mbn", "qcom/sdm845/pixel3/modem.mbn";
> +};
> +
> +&mdss {
> + status = "okay";
> +};
> +
> +&mdss_mdp {
> + status = "okay";
> +};

Not necessary, it is a default state since the commit 4a5622c1d975
("arm64: dts: qcom: sdm845: Don't disable MDP explicitly")

> +
> +&pm8998_gpio {
> + volume_up_gpio: vol-up-active {
> + pins = "gpio6";
> + function = "normal";
> + input-enable;
> + bias-pull-up;
> + qcom,drive-strength = <0>;
> + };
> +
> + panel_pmgpio_pins: panel-pmgpio-active {
> + pins = "gpio2", "gpio5";
> + function = "normal";
> + input-enable;
> + bias-disable;
> + power-source = <0>;
> + };
> +};
> +
> +&pm8998_pon {
> + resin {
> + compatible = "qcom,pm8941-resin";
> + interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>;
> + debounce = <15625>;
> + bias-pull-up;
> + linux,code = <KEY_VOLUMEDOWN>;
> + };

Please move the (disabled, labelled) resin device to pm8998.dtsi and
just add status = "okay" here.

> +};
> +
> +&qupv3_id_0 {
> + status = "okay";
> +};
> +
> +&qupv3_id_1 {
> + status = "okay";
> +};
> +
> +&qup_uart6_default {
> + pinmux {
> + pins = "gpio45", "gpio46", "gpio47", "gpio48";
> + function = "qup6";
> + };
> +
> + cts {
> + pins = "gpio45";
> + bias-disable;
> + };
> +
> + rts-tx {
> + pins = "gpio46", "gpio47";
> + drive-strength = <2>;
> + bias-disable;
> + };
> +
> + rx {
> + pins = "gpio48";
> + bias-pull-up;
> + };
> +};
> +
> +&qup_uart9_default {
> + pinconf-tx {
> + pins = "gpio4";
> + drive-strength = <2>;
> + bias-disable;
> + };
> +
> + pinconf-rx {
> + pins = "gpio5";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
> +};
> +
> +&tlmm {
> + gpio-reserved-ranges = <0 4>, <81 4>;
> +
> + panel_te_pin: panel-te {
> + mux {
> + pins = "gpio12";
> + function = "mdp_vsync";
> + drive-strength = <2>;
> + bias-disable;
> + input-enable;
> + };
> + };
> +
> + panel_reset_pins: panel-active {
> + mux {
> + pins = "gpio6", "gpio52";
> + function = "gpio";
> + drive-strength = <8>;
> + bias-disable = <0>;
> + };
> + };
> +
> + panel_suspend: panel-suspend {
> + mux {
> + pins = "gpio6", "gpio52";
> + function = "gpio";
> + drive-strength = <2>;
> + bias-pull-down;
> + };
> + };
> +
> + touchscreen_reset: ts-reset {
> + mux {
> + pins = "gpio99";
> + function = "gpio";
> + drive-strength = <8>;
> + bias-pull-up;
> + //output-high;

debug, can be removed?

> + };
> + };
> +
> + touchscreen_pins: ts-pins {
> + mux {
> + pins = "gpio125";
> + function = "gpio";
> + drive-strength = <2>;
> + bias-disable;
> + };
> + };
> +
> + touchscreen_i2c_pins: qup-i2c2-gpio {
> + pins = "gpio27", "gpio28";
> + function = "gpio";
> +
> + drive-strength = <2>;
> + bias-disable;
> + };
> +};
> +
> +&uart6 {
> + status = "okay";
> +
> + bluetooth {
> + compatible = "qcom,wcn3990-bt";
> +
> + vddio-supply = <&vreg_s4a_1p8>;
> + vddxo-supply = <&vreg_l7a_1p8>;
> + vddrf-supply = <&vreg_l17a_1p3>;
> + vddch0-supply = <&vreg_l25a_3p3>;
> + max-speed = <3200000>;
> + };
> +};
> +
> +&uart9 {
> + status = "okay";
> +};
> +
> +&usb_1 {
> + status = "okay";
> +};
> +
> +&usb_1_dwc3 {
> + dr_mode = "peripheral";
> +};
> +
> +&usb_1_hsphy {
> + status = "okay";
> +
> + vdd-supply = <&vreg_l1a_0p875>;
> + vdda-pll-supply = <&vreg_l12a_1p8>;
> + vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
> +
> + qcom,imp-res-offset-value = <8>;
> + qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_21_6_MA>;
> + qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_5_PERCENT>;
> + qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>;
> +};
> +
> +&usb_1_qmpphy {
> + status = "okay";
> +
> + vdda-phy-supply = <&vreg_l26a_1p2>;
> + vdda-pll-supply = <&vreg_l1a_0p875>;
> +};
> +
> +&usb_2 {
> + status = "okay";
> +};
> +
> +&usb_2_dwc3 {
> + dr_mode = "host";
> +};
> +
> +&usb_2_hsphy {
> + status = "okay";
> +
> + vdd-supply = <&vreg_l1a_0p875>;
> + vdda-pll-supply = <&vreg_l12a_1p8>;
> + vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
> +
> + qcom,imp-res-offset-value = <8>;
> + qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_22_8_MA>;
> +};
> +
> +&usb_2_qmpphy {
> + status = "okay";
> +
> + vdda-phy-supply = <&vreg_l26a_1p2>;
> + vdda-pll-supply = <&vreg_l1a_0p875>;
> +};
> +
> +&ufs_mem_hc {
> + status = "okay";
> +
> + reset-gpios = <&tlmm 150 GPIO_ACTIVE_LOW>;
> +
> + vcc-supply = <&vreg_l20a_2p95>;
> + vcc-max-microamp = <800000>;
> +};
> +
> +&ufs_mem_phy {
> + status = "okay";
> +
> + vdda-phy-supply = <&vreg_l1a_0p875>;
> + vdda-pll-supply = <&vreg_l26a_1p2>;
> +};
> +
> +&venus {
> + status = "okay";
> + firmware-name = "qcom/sdm845/oneplus6/venus.mbn";

Why are you using the oneplus6 here?

> +};
> +
> +&wifi {
> + status = "okay";
> +
> + vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>;
> + vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
> + vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
> + vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
> +
> + qcom,snoc-host-cap-8bit-quirk;
> + qcom,ath10k-calibration-variant = "google_blueline";

Ideally Kalle Valo should bless this string, added him to the Cc list.
Could you please submit the board file to the ath10k (see [1] for the
description and [2] for an example).


[1] https://wireless.wiki.kernel.org/en/users/drivers/ath10k/boardfiles
[2]
https://lore.kernel.org/ath10k/CAA8EJpphUrxr5gtW0=-tZh-DrKXmHkfFxWMvYRpTUGuCesGCbw@mail.gmail.com/T/#u

> +};


--
With best wishes
Dmitry

\
 
 \ /
  Last update: 2022-07-19 00:14    [W:0.166 / U:0.060 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site