lkml.org 
[lkml]   [2022]   [Jul]   [18]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH] USB: usb-serial-simple: add new device id for OPPO R11
Hi Greg,

On Sun, Jul 17, 2022 at 10:14:43PM +0200, Greg Kroah-Hartman wrote:
> On Sat, Jul 16, 2022 at 02:13:34PM +0200, Reinhard Speyerer wrote:
> > On Fri, Jul 15, 2022 at 10:59:13PM +0800, sdlyyxy wrote:
> > >
> > > > On Jul 15, 2022, at 22:24, Greg Kroah-Hartman <gregkh@linuxfoundation.org> wrote:
> > > >
> > > > The Oppo R11 diagnostic USB connection needs to be bound to the
> > > > usb-serial-simple driver as it just wants to use a dumb pipe to
> > > > communicate to the host.
> > > >
> > > > usb-devices output:
> > > > T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 10 Spd=480 MxCh= 0
> > > > D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
> > > > P: Vendor=22d9 ProdID=276c Rev=04.04
> > > > S: Manufacturer=OPPO
> > > > S: Product=SDM660-MTP _SN:09C6BCA7
> > > > S: SerialNumber=beb2c403
> > > > C: #Ifs= 2 Cfg#= 1 Atr=80 MxPwr=500mA
> > > > I: If#=0x0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30
> > > >
> > > > Reported-by: Yan Xinyu <sdlyyxy@bupt.edu.cn>
> > > > Cc: Johan Hovold <johan@kernel.org>
> > > > Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
> > > > ---
> > > > drivers/usb/serial/usb-serial-simple.c | 4 +++-
> > > > 1 file changed, 3 insertions(+), 1 deletion(-)
> > > >
> > > > diff --git a/drivers/usb/serial/usb-serial-simple.c b/drivers/usb/serial/usb-serial-simple.c
> > > > index 4c6747889a19..eb832b94aa3a 100644
> > > > --- a/drivers/usb/serial/usb-serial-simple.c
> > > > +++ b/drivers/usb/serial/usb-serial-simple.c
> > > > @@ -60,7 +60,9 @@ DEVICE(flashloader, FLASHLOADER_IDS);
> > > > { USB_VENDOR_AND_INTERFACE_INFO(0x18d1, \
> > > > USB_CLASS_VENDOR_SPEC, \
> > > > 0x50, \
> > > > - 0x01) }
> > > > + 0x01) }, \
> > > > + { USB_DEVICE_AND_INTERFACE_INFO(0x22d9, 0x276c, \
> > > > + 0xff, 0xff, 0x30) }
> > > > DEVICE(google, GOOGLE_IDS);
> > > >
> > > > /* Libtransistor USB console */
> > > > --
> > > > 2.37.1
> > > Tested-by: Yan Xinyu <sdlyyxy@bupt.edu.cn>
> >
> > While this may work sufficiently well for real low-volume diag traffic I'd
> > expect a significant percentage of diag messages to be lost in practice
> > with the usb-serial-simple driver.
> >
> > According to the usb-devices output this looks like the Qualcomm USB gadget
> > in the DIAG + ADB composition to me.
> >
> > Since the option driver uses the usb-wwan framework my suggestion would be
> > for the original patch to be applied instead similar to what has been done
> > e.g. for the Quectel RM500Q diag port.
>
> But this is not using the option chip, nor using the option flow control
> protocol at all, so it should not be showing up as a device controlled
> by the option driver. It just will not work properly, the simple driver
> should be doing the exact same thing here.
>

you seem to have the misconception that devices handled by the option driver
would use a USB to serial converter chip from Option similar to e.g. the
ftdi_sio driver which is not the case.

Quoting from option.c:
===
This driver exists because the "normal" serial driver doesn't work too well
with GSM modems. Issues:
- data loss -- one single Receive URB is not nearly enough
- nonstandard flow (Option devices) control
- controlling the baud rate doesn't make sense

This driver is named "option" because the most common device it's
used for is a PC-Card (with an internal OHCI-USB interface, behind
which the GSM interface sits), made by Option Inc.
===

The GSM/UMTS interface in the Option card actually contains a Qualcomm chip
which exports its serial ports via USB. The data loss mentioned by Matthias
above also applies to the diag port.

As can be seen from the sendsetup code in the qcserial driver the
"nonstandard flow (Option devices) control" mentioned above is actually
a Qualcomm "feature" required for some of their USB serial implementations
on tne device to work properly.

In case you suspect potential problems with the sendsetup code and the OPPO
R11 diag port Yan's option.c patch could be extended like this:
{ USB_DEVICE_AND_INTERFACE_INFO(OPPO_VENDOR_ID, OPPO_PRODUCT_R11, 0xff, 0xff, 0x30),
.driver_info = NCTRL(0) },

With a few more lines of code you could also add a new layout to the qcserial
driver if you prefer for the OPPO R11 to be handled by it for some reason.

Either one would be fine with me.

Please don't give the OPPO R11 diag port on Linux a bad name by letting
the usb-serial-simple driver handle it.

Thanks,
Reinhard

\
 
 \ /
  Last update: 2022-07-18 22:48    [W:0.281 / U:0.292 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site