lkml.org 
[lkml]   [2022]   [Jul]   [16]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[net-next PATCH v2 5/5] net: ethernet: stmicro: stmmac: permit MTU change with interface up
Date
Remove the limitation where the interface needs to be down to change
MTU by releasing and opening the stmmac driver to set the new MTU.
Also call the set_filter function to correctly init the port.
This permits to remove the EBUSY error while the ethernet port is
running permitting a correct MTU change if for example a DSA request
a MTU change for a switch CPU port.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
---
.../net/ethernet/stmicro/stmmac/stmmac_main.c | 28 +++++++++++++++----
1 file changed, 22 insertions(+), 6 deletions(-)

diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
index 53e9dbff30ae..7425941fbb40 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
@@ -5551,18 +5551,15 @@ static int stmmac_change_mtu(struct net_device *dev, int new_mtu)
{
struct stmmac_priv *priv = netdev_priv(dev);
int txfifosz = priv->plat->tx_fifo_size;
+ struct stmmac_dma_conf *dma_conf;
const int mtu = new_mtu;
+ int ret;

if (txfifosz == 0)
txfifosz = priv->dma_cap.tx_fifo_size;

txfifosz /= priv->plat->tx_queues_to_use;

- if (netif_running(dev)) {
- netdev_err(priv->dev, "must be stopped to change its MTU\n");
- return -EBUSY;
- }
-
if (stmmac_xdp_is_enabled(priv) && new_mtu > ETH_DATA_LEN) {
netdev_dbg(priv->dev, "Jumbo frames not supported for XDP\n");
return -EINVAL;
@@ -5574,8 +5571,27 @@ static int stmmac_change_mtu(struct net_device *dev, int new_mtu)
if ((txfifosz < new_mtu) || (new_mtu > BUF_SIZE_16KiB))
return -EINVAL;

- dev->mtu = mtu;
+ if (netif_running(dev)) {
+ netdev_dbg(priv->dev, "restarting interface to change its MTU\n");
+ /* Try to allocate the new DMA conf with the new mtu */
+ dma_conf = stmmac_setup_dma_desc(priv, mtu);
+ if (IS_ERR(dma_conf)) {
+ netdev_err(priv->dev, "failed allocating new dma conf for new MTU %d\n",
+ mtu);
+ return PTR_ERR(dma_conf);
+ }

+ stmmac_release(dev);
+
+ ret = __stmmac_open(dev, dma_conf);
+ kfree(dma_conf);
+ if (ret) {
+ netdev_err(priv->dev, "failed reopening the interface after MTU change\n");
+ return ret;
+ }
+ }
+
+ dev->mtu = mtu;
netdev_update_features(dev);

return 0;
--
2.36.1
\
 
 \ /
  Last update: 2022-07-16 20:49    [W:0.104 / U:0.312 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site