lkml.org 
[lkml]   [2022]   [Jul]   [15]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH net-next v3 46/47] arm64: dts: ls1046ardb: Add serdes bindings
Date
This adds appropriate bindings for the macs which use the SerDes. The
156.25MHz fixed clock is a crystal. The 100MHz clocks (there are
actually 3) come from a Renesas 6V49205B at address 69 on i2c0. There is
no driver for this device (and as far as I know all you can do with the
100MHz clocks is gate them), so I have chosen to model it as a single
fixed clock.

Note: the SerDes1 lane numbering for the LS1046A is *reversed*.
This means that Lane A (what the driver thinks is lane 0) uses pins
SD1_TX3_P/N.

Because this will break ethernet if the serdes is not enabled, enable
the serdes driver by default on Layerscape.

Signed-off-by: Sean Anderson <sean.anderson@seco.com>
---
Please let me know if there is a better/more specific config I can use
here.

(no changes since v1)

.../boot/dts/freescale/fsl-ls1046a-rdb.dts | 34 +++++++++++++++++++
drivers/phy/freescale/Kconfig | 1 +
2 files changed, 35 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1046a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-ls1046a-rdb.dts
index 7025aad8ae89..4f4dd0ed8c53 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1046a-rdb.dts
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1046a-rdb.dts
@@ -26,6 +26,32 @@ aliases {
chosen {
stdout-path = "serial0:115200n8";
};
+
+ clocks {
+ clk_100mhz: clock-100mhz {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <100000000>;
+ };
+
+ clk_156mhz: clock-156mhz {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <156250000>;
+ };
+ };
+};
+
+&serdes1 {
+ clocks = <&clk_100mhz>, <&clk_156mhz>;
+ clock-names = "ref0", "ref1";
+ status = "okay";
+};
+
+&serdes2 {
+ clocks = <&clk_100mhz>, <&clk_100mhz>;
+ clock-names = "ref0", "ref1";
+ status = "okay";
};

&duart0 {
@@ -140,21 +166,29 @@ ethernet@e6000 {
ethernet@e8000 {
phy-handle = <&sgmii_phy1>;
phy-connection-type = "sgmii";
+ phys = <&serdes1 1>;
+ phy-names = "serdes";
};

ethernet@ea000 {
phy-handle = <&sgmii_phy2>;
phy-connection-type = "sgmii";
+ phys = <&serdes1 0>;
+ phy-names = "serdes";
};

ethernet@f0000 { /* 10GEC1 */
phy-handle = <&aqr106_phy>;
phy-connection-type = "xgmii";
+ phys = <&serdes1 3>;
+ phy-names = "serdes";
};

ethernet@f2000 { /* 10GEC2 */
fixed-link = <0 1 1000 0 0>;
phy-connection-type = "xgmii";
+ phys = <&serdes1 2>;
+ phy-names = "serdes";
};

mdio@fc000 {
diff --git a/drivers/phy/freescale/Kconfig b/drivers/phy/freescale/Kconfig
index fe2a3efe0ba4..9595666213d0 100644
--- a/drivers/phy/freescale/Kconfig
+++ b/drivers/phy/freescale/Kconfig
@@ -43,6 +43,7 @@ config PHY_FSL_LYNX_10G
tristate "Freescale Layerscale Lynx 10G SerDes support"
select GENERIC_PHY
select REGMAP_MMIO
+ default y if ARCH_LAYERSCAPE
help
This adds support for the Lynx "SerDes" devices found on various QorIQ
SoCs. There may be up to four SerDes devices on each SoC, and each
--
2.35.1.1320.gc452695387.dirty
\
 
 \ /
  Last update: 2022-07-16 00:08    [W:0.532 / U:0.948 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site