lkml.org 
[lkml]   [2022]   [Jul]   [14]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
SubjectRe: [PATCH] arm64: dts: rockchip: Fix SD card init on rk3399-nanopi4
From
On 2022-07-14 00:41, Heiko Stübner wrote:
> Hi Christian,
>
> Am Donnerstag, 14. Juli 2022, 00:22:23 CEST schrieb Christian Kohlschütter:
>> mmc/SD-card initialization may sometimes fail on NanoPi r4s with
>> "mmc1: problem reading SD Status register" /
>> "mmc1: error -110 whilst initialising SD card"
>>
>> Moreover, rebooting would also sometimes hang.
>>
>
> Nit: here the commit message should continue with something like:
> -----
> This is caused by the vcc3v0-sd regulator referencing the wrong gpio.
>
> Fix the regulator to use the correct pin and drop the always-on property.
> -----
>> Signed-off-by: Christian Kohlschütter <christian@kohlschutter.com>
>> ---
>> arch/arm64/boot/dts/rockchip/rk3399-nanopi4.dtsi | 6 +++---
>> 1 file changed, 3 insertions(+), 3 deletions(-)
>>
>> diff --git a/arch/arm64/boot/dts/rockchip/rk3399-nanopi4.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-nanopi4.dtsi
>> index 8c0ff6c96e03..91789801ab03 100644
>> --- a/arch/arm64/boot/dts/rockchip/rk3399-nanopi4.dtsi
>> +++ b/arch/arm64/boot/dts/rockchip/rk3399-nanopi4.dtsi
>> @@ -67,10 +67,10 @@ vcc1v8_s3: vcc1v8-s3 {
>> vcc3v0_sd: vcc3v0-sd {
>> compatible = "regulator-fixed";
>> enable-active-high;
>> - gpio = <&gpio0 RK_PA1 GPIO_ACTIVE_HIGH>;
>> + gpio = <&gpio0 RK_PD6 GPIO_ACTIVE_HIGH>;
>
> The interesting question would be how nano-pi-specific that gpio is.
>
> I.e. this is the rk3399-nanopi4.dtsi that is shared by multiple board types,
> so can you check in schematics if gpio0-d6 is always used on all of them?

On the R4S schematic, this is GPIO0_A1 same as the others. GPIO0 doesn't
even have a bank D on RK3399, it only goes up to B5 :/

>
> Thanks
> Heiko
>
>> pinctrl-names = "default";
>> pinctrl-0 = <&sdmmc0_pwr_h>;
>> - regulator-always-on;
>> + regulator-boot-on;
>> regulator-min-microvolt = <3000000>;
>> regulator-max-microvolt = <3000000>;
>> regulator-name = "vcc3v0_sd";
>> @@ -580,7 +580,7 @@ wifi_reg_on_h: wifi-reg_on-h {
>>
>> sdmmc {
>> sdmmc0_det_l: sdmmc0-det-l {
>> - rockchip,pins = <0 RK_PA7 RK_FUNC_GPIO &pcfg_pull_up>;
>> + rockchip,pins = <0 RK_PD6 RK_FUNC_GPIO &pcfg_pull_up>;

...and claiming the card detect is on the same non-existent pin as the
regulator enable is clearly even more wrong.

Is this another case where a UHS card is involved, such that VCC_SDIO
gets left at 1.8V after a reboot, so subsequent attempts to do the
initial handshake where the card is expecting 3V logic levels fail? (AKA
the Tinkerboard problem). Hobbling the regulator such that Linux can
never actually turn VCC3V0_SD off, thus the card never gets reset, might
appear to "work", but isn't the right thing to do.

Robin.

>> };
>>
>> sdmmc0_pwr_h: sdmmc0-pwr-h {
>>
>
>
>
>
>
> _______________________________________________
> Linux-rockchip mailing list
> Linux-rockchip@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-rockchip

\
 
 \ /
  Last update: 2022-07-14 13:43    [W:0.598 / U:0.484 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site