lkml.org 
[lkml]   [2022]   [Jul]   [11]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
SubjectRe: [PATCH v2] arm64: dts: qcom: sc7280: Move wcd specific pin conf to common file
From

On 7/8/2022 11:29 PM, Stephen Boyd wrote:
Thanks for your time Stephen!!!
> Quoting Srinivasa Rao Mandadapu (2022-07-07 05:36:21)
>> diff --git a/arch/arm64/boot/dts/qcom/sc7280-herobrine-audio-wcd9385.dtsi b/arch/arm64/boot/dts/qcom/sc7280-herobrine-audio-wcd9385.dtsi
>> index 32a1e78..859faaa 100644
>> --- a/arch/arm64/boot/dts/qcom/sc7280-herobrine-audio-wcd9385.dtsi
>> +++ b/arch/arm64/boot/dts/qcom/sc7280-herobrine-audio-wcd9385.dtsi
>> @@ -5,6 +5,70 @@
>> * Copyright (c) 2022, The Linux Foundation. All rights reserved.
>> */
>>
>> +/* PINCTRL */
>> +
>> +&lpass_dmic01_clk {
>> + drive-strength = <8>;
>> + bias-disable;
>> +};
>> +
>> +&lpass_dmic01_clk_sleep {
>> + drive-strength = <2>;
>> +};
>> +
>> +&lpass_dmic01_data {
>> + bias-pull-down;
>> +};
>> +
>> +&lpass_dmic23_clk {
>> + drive-strength = <8>;
>> + bias-disable;
>> +};
>> +
>> +&lpass_dmic23_clk_sleep {
>> + drive-strength = <2>;
>> +};
>> +
>> +&lpass_dmic23_data {
>> + bias-pull-down;
>> +};
>> +
>> +&lpass_rx_swr_clk {
>> + drive-strength = <2>;
>> + slew-rate = <1>;
>> + bias-disable;
>> +};
>> +
>> +&lpass_rx_swr_clk_sleep {
>> + bias-pull-down;
>> +};
>> +
>> +&lpass_rx_swr_data {
>> + drive-strength = <2>;
> I suspect this was discussed before, but why do we need to modify drive
> strengths on pins that aren't in output mode? I assume either rx_swr or
> tx_swr is unidirectional.

Actually this patch is just reorganization only. didn't do any
modification of already reviewed patches.

Will test without drive strength again and post a fix patch post this
patch accepted if required.

>
>> + slew-rate = <1>;
>> + bias-bus-hold;
>> +};
>> +
>> +&lpass_rx_swr_data_sleep {
>> + bias-pull-down;
>> +};
>> +
>> +&lpass_tx_swr_clk {
>> + drive-strength = <2>;
>> + slew-rate = <1>;
>> + bias-disable;
>> +};
>> +
>> +&lpass_tx_swr_clk_sleep {
>> + bias-pull-down;
>> +};
>> +
>> +&lpass_tx_swr_data {
>> + drive-strength = <2>;
>> + slew-rate = <1>;
>> + bias-bus-hold;
>> +};
>> +
>> &mi2s1_data0 {
>> drive-strength = <6>;
>> bias-disable;

\
 
 \ /
  Last update: 2022-07-11 09:54    [W:0.091 / U:0.464 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site