lkml.org 
[lkml]   [2022]   [Jul]   [1]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v1 3/9] dt-bindings: reset: intel,rcu-gw: Update bindings for "legacy" SoCs
On Tue, Jun 28, 2022 at 02:44:35PM +0200, Martin Blumenstingl wrote:
> The Lantiq Amazon-SE, Danube, xRX100 and xRX200 SoCs have up to two USB2
> PHYs which are part of the RCU register space. The RCU registers on
> these SoCs are using big endian. Update the binding for these SoCs to
> properly describe this IP:
> - Add compatible strings for Amazon-SE, Danube and xRX100
> - Rename the xRX200 compatible string (which is not used anywhere) and
> switch to the one previously documented in mips/lantiq/rcu.txt
> - Allow usage of "simple-mfd" and "syscon" in the compatible string so the
> child devices (USB2 PHYs) can be described
> - Allow #address-cells and #size-cells to be set to 1 for describing the
> child devices (USB2 PHYs)
> - #reset-cells must always be 3 (offset, reset bit and status bit) on the
> legacy SoCs while LGM uses a fixed value of 2 (offset and reset bit -
> status bit is always identical to the reset bit).
>
> Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
> ---
> .../bindings/reset/intel,rcu-gw.yaml | 84 +++++++++++++++++--
> 1 file changed, 79 insertions(+), 5 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/reset/intel,rcu-gw.yaml b/Documentation/devicetree/bindings/reset/intel,rcu-gw.yaml
> index be64f8597710..b90913c7b7d3 100644
> --- a/Documentation/devicetree/bindings/reset/intel,rcu-gw.yaml
> +++ b/Documentation/devicetree/bindings/reset/intel,rcu-gw.yaml
> @@ -11,9 +11,16 @@ maintainers:
>
> properties:
> compatible:
> - enum:
> - - intel,rcu-lgm
> - - intel,rcu-xrx200

It is okay to remove/change this because ?

> + oneOf:
> + - items:
> + - enum:
> + - lantiq,ase-rcu
> + - lantiq,danube-rcu
> + - lantiq,xrx100-rcu
> + - lantiq,xrx200-rcu
> + - const: simple-mfd

This says child nodes have 0 dependence on anything in the parent node.
Such as a clock in the parent needing to be enabled.

> + - const: syscon

Given the child nodes depend on this, I find the combination to be a
contradiction. But it's widely used, so oh well.

> + - const: intel,rcu-lgm
>
> reg:
> description: Reset controller registers.
> @@ -33,8 +40,6 @@ properties:
> maximum: 31
>
> "#reset-cells":
> - minimum: 2
> - maximum: 3
> description: |
> First cell is reset request register offset.
> Second cell is bit offset in reset request register.
> @@ -43,6 +48,43 @@ properties:
> reset request and reset status registers is same. Whereas
> 3 for legacy SoCs as bit offset differs.
>
> + "#address-cells":
> + const: 1
> +
> + "#size-cells":
> + const: 1
> +
> + big-endian: true
> +
> +patternProperties:
> + "^usb2-phy@[0-9a-f]+$":
> + type: object
> + $ref: "../phy/lantiq,xway-rcu-usb2-phy.yaml"
> +
> +allOf:
> + - if:
> + properties:
> + compatible:
> + contains:
> + const: intel,rcu-lgm
> + then:
> + properties:
> + "#reset-cells":
> + const: 2

else:
properties:
"#reset-cells":
const: 3

> + - if:
> + properties:
> + compatible:
> + contains:
> + enum:
> + - lantiq,ase-rcu
> + - lantiq,danube-rcu
> + - lantiq,xrx100-rcu
> + - lantiq,xrx200-rcu
> + then:
> + properties:
> + "#reset-cells":
> + const: 3
> +
> required:
> - compatible
> - reg
> @@ -67,3 +109,35 @@ examples:
> #pwm-cells = <2>;
> resets = <&rcu0 0x30 21>;
> };
> + - |
> + rcu_xrx200: rcu@203000 {
> + compatible = "lantiq,xrx200-rcu", "simple-mfd", "syscon";
> + reg = <0x203000 0x100>;
> + big-endian;
> +
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + #reset-cells = <3>;
> + intel,global-reset = <0x10 30 29>;
> +
> + usb_phy0: usb2-phy@18 {
> + compatible = "lantiq,xrx200-usb2-phy";
> + reg = <0x18 4>, <0x38 4>;
> + status = "disabled";

Why is your example disabled? Don't use 'status' in examples.

> +
> + resets = <&rcu_xrx200 0x48 4 4>, <&rcu_xrx200 0x10 4 4>;

Humm, a dependency on the parent. Not a 'simple-mfd'.

> + reset-names = "phy", "ctrl";
> + #phy-cells = <0>;
> + };
> +
> + usb_phy1: usb2-phy@34 {
> + compatible = "lantiq,xrx200-usb2-phy";
> + reg = <0x34 4>, <0x3c 4>;
> + status = "disabled";
> +
> + resets = <&rcu_xrx200 0x48 5 5>, <&rcu_xrx200 0x10 4 4>;
> + reset-names = "phy", "ctrl";
> + #phy-cells = <0>;
> + };
> + };
> --
> 2.36.1
>
>

\
 
 \ /
  Last update: 2022-07-01 18:35    [W:1.277 / U:0.004 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site