lkml.org 
[lkml]   [2022]   [Jun]   [9]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v3 1/3] dt-bindings: leds: Add bindings for the TLC5925 controller
Date
Add bindings documentation for the TLC5925 LED controller.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@traphandler.com>
---
.../devicetree/bindings/leds/ti,tlc5925.yaml | 107 ++++++++++++++++++
1 file changed, 107 insertions(+)
create mode 100644 Documentation/devicetree/bindings/leds/ti,tlc5925.yaml

diff --git a/Documentation/devicetree/bindings/leds/ti,tlc5925.yaml b/Documentation/devicetree/bindings/leds/ti,tlc5925.yaml
new file mode 100644
index 000000000000..12a71e48f854
--- /dev/null
+++ b/Documentation/devicetree/bindings/leds/ti,tlc5925.yaml
@@ -0,0 +1,107 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/leds/ti,tlc5925.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: LEDs connected to TI TLC5925 controller
+
+maintainers:
+ - Jean-Jacques Hiblot <jjhiblot@traphandler.com>
+
+description: |
+ The TLC5925 is a low-power 16-channel constant-current LED sink driver.
+ It is controlled through a SPI interface.
+ It is built around a shift register and latches which convert serial
+ input data into a parallel output. Several TLC5925 can be chained to
+ control more than 16 LEDs with a single chip-select.
+ The brightness level cannot be controlled, each LED is either on or off.
+
+ Each LED is represented as a sub-node of the ti,tlc5925 device.
+
+$ref: /schemas/spi/spi-peripheral-props.yaml#
+
+properties:
+ compatible:
+ const: ti,tlc5925
+
+ ti,shift-register-length:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 8
+ description: |
+ The length of the shift register. If several TLC5925 are chained,
+ shift_register_length should be set to 16 times the number of TLC5925.
+ The value must be a multiple of 8.
+
+ "#address-cells":
+ const: 1
+
+ "#size-cells":
+ const: 0
+
+ output-enable-b-gpios:
+ $ref: /schemas/types.yaml#/definitions/phandle-array
+ description: |
+ Optional GPIO pins to enable/disable the parallel output. They describe
+ the GPIOs connected to the OE/ pin of the TLC5925s.
+
+patternProperties:
+ "@[0-9a-f]+$":
+ type: object
+ $ref: common.yaml#
+
+ properties:
+ reg:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: |
+ LED pin number (must be lower than ti,shift-register-length).
+ The furthest LED down the chain has the pin number 0.
+
+ required:
+ - reg
+
+required:
+ - "#address-cells"
+ - "#size-cells"
+ - ti,shift-register-length
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/gpio/gpio.h>
+ #include <dt-bindings/leds/common.h>
+
+ spi0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ leds@2 {
+ compatible = "ti,tlc5925";
+ reg = <0x02>;
+ spi-max-frequency = <30000000>;
+ ti,shift-register-length = <32>;
+ output-enable-b-gpios = <&gpio0b 9 GPIO_ACTIVE_HIGH>, <&gpio0b 7 GPIO_ACTIVE_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led@0 {
+ reg = <0>;
+ function = LED_FUNCTION_STATUS;
+ color = <LED_COLOR_ID_GREEN>;
+ };
+
+ led@4 {
+ reg = <4>;
+ function = LED_FUNCTION_STATUS;
+ color = <LED_COLOR_ID_RED>;
+ };
+
+ led@1f {
+ reg = <31>;
+ function = LED_FUNCTION_PANIC;
+ color = <LED_COLOR_ID_RED>;
+ };
+ };
+
+ };
--
2.25.1
\
 
 \ /
  Last update: 2022-06-09 18:28    [W:0.079 / U:0.288 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site