lkml.org 
[lkml]   [2022]   [Jun]   [8]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v10 18/21] drm/mediatek: Add mt8195 Embedded DisplayPort driver
From
Date
On Wed, 2022-06-08 at 17:15 +0800, CK Hu wrote:
> Hi, Rex:
>
> On Wed, 2022-06-08 at 16:43 +0800, Rex-BC Chen wrote:
> > On Wed, 2022-06-08 at 10:23 +0800, CK Hu wrote:
> > > Hi, Rex:
> > >
> > > On Tue, 2022-06-07 at 20:24 +0800, Rex-BC Chen wrote:
> > > > On Tue, 2022-06-07 at 14:21 +0800, CK Hu wrote:
> > > > > Hi, Rex:
> > > > >
> > > > > On Mon, 2022-05-23 at 12:47 +0200, Guillaume Ranquet wrote:
> > > > > > From: Markus Schneider-Pargmann <msp@baylibre.com>
> > > > > >
> > > > > > This patch adds a DisplayPort driver for the Mediatek
> > > > > > mt8195
> > > > > > SoC.
> > > > > >
> > > > > > It supports the mt8195, the embedded DisplayPort units. It
> > > > > > offers
> > > > > > DisplayPort 1.4 with up to 4 lanes.
> > > > > >
> > > > > > The driver creates a child device for the phy. The child
> > > > > > device
> > > > > > will
> > > > > > never exist without the parent being active. As they are
> > > > > > sharing
> > > > > > a
> > > > > > register range, the parent passes a regmap pointer to the
> > > > > > child
> > > > > > so
> > > > > > that
> > > > > > both can work with the same register range. The phy driver
> > > > > > sets
> > > > > > device
> > > > > > data that is read by the parent to get the phy device that
> > > > > > can
> > > > > > be
> > > > > > used
> > > > > > to control the phy properties.
> > > > > >
> > > > > > This driver is based on an initial version by
> > > > > > Jason-JH.Lin <jason-jh.lin@mediatek.com>.
> > > > > >
> > > > > > Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
> > > > > > Signed-off-by: Guillaume Ranquet <granquet@baylibre.com>
> > > > > > ---
> > > > >
> > > > > [snip]
> > > > >
> > > > > > +
> > > > > > +static irqreturn_t mtk_dp_hpd_event_thread(int hpd, void
> > > > > > *dev)
> > > > > > +{
> > > > > > + struct mtk_dp *mtk_dp = dev;
> > > > > > + int event;
> > > > > > + u8 buf[DP_RECEIVER_CAP_SIZE] = {};
> > > > > > +
> > > > > > + event = mtk_dp_plug_state(mtk_dp) ?
> > > > > > connector_status_connected
> > > > > > :
> > > > > > + connector_sta
> > > > > > tus_disc
> > > > > > onnected;
> > > > > > +
> > > > > > + if (event < 0)
> > > > >
> > > > > event is always > 0, isn't it?
> > > > >
> > > >
> > > > Hello CK,
> > > >
> > > > ok, I will move this to dp patch.
> > > >
> > > > > > + return IRQ_HANDLED;
> > > > > > +
> > > > > > + if (mtk_dp->drm_dev) {
> > > > > > + dev_info(mtk_dp->dev,
> > > > > > "drm_helper_hpd_irq_event\n");
> > > > > > + drm_helper_hpd_irq_event(mtk_dp->bridge.dev);
> > > > >
> > > > > I think this ISR would come once. If bridge has not attached,
> > > > > the
> > > > > drm
> > > > > core would lost this event. Maybe you should enable eDP
> > > > > hardware
> > > > > after
> > > > > bridge attached or send this event when attached.
> > > > >
> > > >
> > > > for edp patch, I will move it to (mtk_dp_bridge_attach).
> > > > for dp patch, I will add it back.
> > >
> > > I find out that mtk_dp_poweron() is in top of
> > > mtk_dp_bridge_attach().
> > > If move mtk_dp_poweron() to bottom of mtk_dp_bridge_attach(),
> > > mtk_dp-
> > > > drm_dev would not be NULL here. So we could drop this checking.
> > > >
> >
> > Hello CK,
> >
> > If we failed to setup phy(ret!=0), we alos need to deattach this
> > bridge.
> > I don't think it's a good idea just for remove this.
>
> OK, move mtk_dp_hwirq_enable() out of mtk_dp_poweron() and to the
> bottom of mtk_dp_bridge_attach(). irq is not part of power.
>

I will do this and drop "if (mtk_dp->drm_dev)"

> >
> > > > > > + }
> > > > > > +
> > > > > > + if (mtk_dp->train_info.cable_state_change) {
> > > > >
> > > > > Executing this thread imply cable_state_change = true, so
> > > > > drop
> > > > > cable_state_change.
> > > > >
> > > >
> > > > In mtk_dp_hpd_isr_handler(), there is another irq
> > > > "MTK_DP_HPD_INTERRUPT" which means the sink devices give a
> > > > interrupt
> > > > to
> > > > source device. it's not about connected status, so I think we
> > > > still
> > > > need this.
> > >
> > > In bottom of mtk_dp_hpd_isr_handler(), the code is:
> > >
> > > + train_info->cable_state_change = true;
> > > +
> > > + return IRQ_WAKE_THREAD;
> > >
> > > This thread is called only when return IRQ_WAKE_THREAD, and
> > > before
> > > return IRQ_WAKE_THREAD, train_info->cable_state_change is always
> > > set
> > > to
> > > true. So in this thread, train_info->cable_state_change must be
> > > true.
> > >
> >
> > As mentioned, this irq handler function is not only for connected
> > status.
> >
> > this could be return if this irq is interrupt from sink device.
> > + if (!(train_info->irq_status &
> > + (MTK_DP_HPD_CONNECT | MTK_DP_HPD_DISCONNECT)))
> > + return IRQ_HANDLED;
>
> According to [1], return IRQ_WAKE_THREAD to wake up thread. So return
> IRQ_HANDLED would not wake up thread.
>
> [1]
>
https://www.kernel.org/doc/htmldocs/kernel-api/API-request-threaded-irq.html
>
> Regards,
> CK
>

yes, you are right. I will return IRQ_WAKE_THREAD for handle sink
interrupt.

> >
> > BRs,
> > Bo-Chen
> > > Regards,
> > > CK
> > >
> > > >
> > > > > > + mtk_dp->train_info.cable_state_change = false;
> > > > > > +
> > > > > > + mtk_dp->train_state =
> > > > > > MTK_DP_TRAIN_STATE_STARTUP;
> > > > > > +
> > > > > > + if (!mtk_dp->train_info.cable_plugged_in ||
> > > > > > + !mtk_dp_plug_state(mtk_dp)) {
> > > > >
> > > > > I do not like two variable to present one thing. If
> > > > >
> > > > > mtk_dp->train_info.cable_plugged_in = false
> > > > > and
> > > > > mtk_dp_plug_state(mtk_dp) = ture
> > > > >
> > > > > What does this mean? I think this mean 'now' is connected
> > > > > because
> > > > > cable_plugged_in is old information and mtk_dp_plug_state()
> > > > > is
> > > > > current
> > > > > information.
> > > > >
> > > > > But I would like to keep cable_plugged_in and drop
> > > > > mtk_dp_plug_state()
> > > > > because cable_plugged_in would be changed in isr and it would
> > > > > be
> > > > > the
> > > > > same as mtk_dp_plug_state().
> > > > >
> > > > > Regards,
> > > > > CK
> > > > >
> > > >
> > > > ok, I will drop this.
> > > >
> > > > BRs,
> > > > Rex
> > > >
> > > > > > + mtk_dp_video_mute(mtk_dp, true);
> > > > > > +
> > > > > > + mtk_dp_initialize_priv_data(mtk_dp);
> > > > > > + mtk_dp_set_idle_pattern(mtk_dp, true);
> > > > > > + if (mtk_dp->has_fec)
> > > > > > + mtk_dp_fec_enable(mtk_dp,
> > > > > > false);
> > > > > > +
> > > > > > + mtk_dp_update_bits(mtk_dp,
> > > > > > MTK_DP_TOP_PWR_STATE,
> > > > > > + DP_PWR_STATE_BANDGAP
> > > > > > _TPLL,
> > > > > > + DP_PWR_STATE_MASK);
> > > > > > + } else {
> > > > > > + mtk_dp_update_bits(mtk_dp,
> > > > > > MTK_DP_TOP_PWR_STATE,
> > > > > > + DP_PWR_STATE_BANDGAP
> > > > > > _TPLL_LA
> > > > > > NE,
> > > > > > + DP_PWR_STATE_MASK);
> > > > > > + drm_dp_read_dpcd_caps(&mtk_dp->aux,
> > > > > > buf);
> > > > > > + mtk_dp->train_info.link_rate =
> > > > > > + min_t(int, mtk_dp-
> > > > > > > max_linkrate,
> > > > > >
> > > > > > + buf[mtk_dp-
> > > > > > > max_linkrate]);
> > > > > >
> > > > > > + mtk_dp->train_info.lane_count =
> > > > > > + min_t(int, mtk_dp->max_lanes,
> > > > > > + drm_dp_max_lane_count(buf
> > > > > > ));
> > > > > > + }
> > > > > > + }
> > > > > > +
> > > > > > + if (mtk_dp->train_info.irq_status &
> > > > > > MTK_DP_HPD_INTERRUPT) {
> > > > > > + dev_dbg(mtk_dp->dev, "MTK_DP_HPD_INTERRUPT\n");
> > > > > > + mtk_dp->train_info.irq_status &=
> > > > > > ~MTK_DP_HPD_INTERRUPT;
> > > > > > + mtk_dp_hpd_sink_event(mtk_dp);
> > > > > > + }
> > > > > > +
> > > > > > + return IRQ_HANDLED;
> > > > > > +}
> > > > > > +
> > > > >
> > > > >
> > > >
> > > >
> > >
> > >
> >
> >
>
>

\
 
 \ /
  Last update: 2022-06-08 13:55    [W:0.304 / U:0.084 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site