lkml.org 
[lkml]   [2022]   [Jun]   [8]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v10 18/21] drm/mediatek: Add mt8195 Embedded DisplayPort driver
From
Date
On Wed, 2022-06-08 at 16:45 +0800, CK Hu wrote:
> Hi, Rex:
>
> On Mon, 2022-05-23 at 12:47 +0200, Guillaume Ranquet wrote:
> > From: Markus Schneider-Pargmann <msp@baylibre.com>
> >
> > This patch adds a DisplayPort driver for the Mediatek mt8195 SoC.
> >
> > It supports the mt8195, the embedded DisplayPort units. It offers
> > DisplayPort 1.4 with up to 4 lanes.
> >
> > The driver creates a child device for the phy. The child device
> > will
> > never exist without the parent being active. As they are sharing a
> > register range, the parent passes a regmap pointer to the child so
> > that
> > both can work with the same register range. The phy driver sets
> > device
> > data that is read by the parent to get the phy device that can be
> > used
> > to control the phy properties.
> >
> > This driver is based on an initial version by
> > Jason-JH.Lin <jason-jh.lin@mediatek.com>.
> >
> > Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
> > Signed-off-by: Guillaume Ranquet <granquet@baylibre.com>
> > ---
>
> [snip]
>
> > +
> > +static bool mtk_dp_set_swing_pre_emphasis(struct mtk_dp *mtk_dp,
> > int
> > lane_num,
> > + int swing_val, int
> > preemphasis)
>
> The return value is never processed, so let this function to be void.
>
> Regards,
> CK
>

Hello CK,

ok, I will drop this.
Actually, I change "mtk_dp_write", "mtk_dp_update_bits" and
"mtk_dp_bulk_16bit_write" to return void. I don't think we need to
handle the issue that we failed to set registers. If we failed to set
register, it's because hw is not enable.

Therefore, I drop this and we can reduce many lines of codes.

BRs,
Bo-Chen
> > +{
> > + int ret;
> > +
> > + u32 lane_shift = lane_num * DP_TX1_VOLT_SWING_SHIFT;
> > +
> > + if (lane_num < 0 || lane_num > 3)
>
> lane_num < 0 would not happen. lane_num > 3 only if device tree max
> lane is wrong. So I would like to checkout max lane when parsing
> device
> tree instead of checking here.
> > + return false;
> > +
> > + dev_dbg(mtk_dp->dev,
> > + "link training swing_val= 0x%x, preemphasis = 0x%x\n",
> > + swing_val, preemphasis);
> > +
> > + ret = mtk_dp_update_bits(mtk_dp, MTK_DP_TOP_SWING_EMP,
> > + swing_val << (DP_TX0_VOLT_SWING_SHIFT
> > + lane_shift),
> > + DP_TX0_VOLT_SWING_MASK << lane_shift);
> > + if (ret)
> > + return ret;
> > + ret = mtk_dp_update_bits(mtk_dp, MTK_DP_TOP_SWING_EMP,
> > + preemphasis << (DP_TX0_PRE_EMPH_SHIFT
> > + lane_shift),
> > + DP_TX0_PRE_EMPH_MASK << lane_shift);
> > +
> > + return !ret;
> > +}
> > +
>
>

\
 
 \ /
  Last update: 2022-06-08 11:32    [W:0.341 / U:0.668 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site