lkml.org 
[lkml]   [2022]   [Jun]   [8]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v10 18/21] drm/mediatek: Add mt8195 Embedded DisplayPort driver
From
Date
Hi, Rex:

On Mon, 2022-05-23 at 12:47 +0200, Guillaume Ranquet wrote:
> From: Markus Schneider-Pargmann <msp@baylibre.com>
>
> This patch adds a DisplayPort driver for the Mediatek mt8195 SoC.
>
> It supports the mt8195, the embedded DisplayPort units. It offers
> DisplayPort 1.4 with up to 4 lanes.
>
> The driver creates a child device for the phy. The child device will
> never exist without the parent being active. As they are sharing a
> register range, the parent passes a regmap pointer to the child so
> that
> both can work with the same register range. The phy driver sets
> device
> data that is read by the parent to get the phy device that can be
> used
> to control the phy properties.
>
> This driver is based on an initial version by
> Jason-JH.Lin <jason-jh.lin@mediatek.com>.
>
> Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
> Signed-off-by: Guillaume Ranquet <granquet@baylibre.com>
> ---

[snip]

> +
> +static bool mtk_dp_parse_capabilities(struct mtk_dp *mtk_dp)
> +{
> + u8 buf[DP_RECEIVER_CAP_SIZE] = {};
> + u8 val;
> + struct mtk_dp_train_info *train_info = &mtk_dp->train_info;
> +
> + if (!mtk_dp_plug_state(mtk_dp))
> + return false;
> +
> + drm_dp_dpcd_writeb(&mtk_dp->aux, DP_SET_POWER,
> DP_SET_POWER_D0);
> + /* Wait for power on */
> + usleep_range(2000, 5000);
> +
> + drm_dp_read_dpcd_caps(&mtk_dp->aux, buf);
> +
> + memcpy(mtk_dp->rx_cap, buf, min(sizeof(mtk_dp->rx_cap),
> sizeof(buf)));

sizeof(mtk_dp->rx_cap) is identical to sizeof(buf), so

drm_dp_read_dpcd_caps(&mtk_dp->aux, mtk_dp->rx_cap);


> + mtk_dp->rx_cap[DP_TRAINING_AUX_RD_INTERVAL] &=
> DP_TRAINING_AUX_RD_MASK;
> +
> + train_info->link_rate =
> + min_t(int, mtk_dp->max_linkrate, buf[mtk_dp-
> >max_linkrate]);
> + train_info->lane_count =
> + min_t(int, mtk_dp->max_lanes,
> drm_dp_max_lane_count(buf));
> +
> + train_info->tps3 = drm_dp_tps3_supported(buf);
> + train_info->tps4 = drm_dp_tps4_supported(buf);
> +
> + train_info->sink_ssc =
> + !!(buf[DP_MAX_DOWNSPREAD] & DP_MAX_DOWNSPREAD_0_5);
> +
> + train_info->sink_ssc = false;

What does these two statement do?

Regards,
CK

> +
> + drm_dp_dpcd_readb(&mtk_dp->aux, DP_MSTM_CAP, &val);
> + if (val & DP_MST_CAP) {
> + /* Clear DP_DEVICE_SERVICE_IRQ_VECTOR_ESI0 */
> + drm_dp_dpcd_readb(&mtk_dp->aux,
> + DP_DEVICE_SERVICE_IRQ_VECTOR_ESI0,
> &val);
> + if (val)
> + drm_dp_dpcd_writeb(&mtk_dp->aux,
> + DP_DEVICE_SERVICE_IRQ_VECTOR
> _ESI0,
> + val);
> + }
> +
> + return true;
> +}
> +

\
 
 \ /
  Last update: 2022-06-08 11:12    [W:0.583 / U:0.116 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site