lkml.org 
[lkml]   [2022]   [Jun]   [7]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 3/4] arm64: dts: qcom: sc8280x: Add reference device
Date
Add basic support for the SC8280XP reference device, which allows it to
boot to a shell (using EFIFB) with functional storage (UFS), USB,
keyboard, touchpad, touchscreen, backlight and remoteprocs.

The PMICs are, per socinfo, reused from other platforms. But given that
the address of the PMICs doesn't match other cases and that it's
desirable to label things according to the schematics a new dtsi file is
created to represent the reference combination of PMICs.

Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
---
arch/arm64/boot/dts/qcom/Makefile | 1 +
arch/arm64/boot/dts/qcom/sc8280xp-crd.dts | 423 +++++++++++++++++++
arch/arm64/boot/dts/qcom/sc8280xp-pmics.dtsi | 108 +++++
3 files changed, 532 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/sc8280xp-crd.dts
create mode 100644 arch/arm64/boot/dts/qcom/sc8280xp-pmics.dtsi

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 2f8aec2cc6db..ceeae094a59f 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -89,6 +89,7 @@ dtb-$(CONFIG_ARCH_QCOM) += sc7280-herobrine-villager-r0.dtb
dtb-$(CONFIG_ARCH_QCOM) += sc7280-idp.dtb
dtb-$(CONFIG_ARCH_QCOM) += sc7280-idp2.dtb
dtb-$(CONFIG_ARCH_QCOM) += sc7280-crd-r3.dtb
+dtb-$(CONFIG_ARCH_QCOM) += sc8280xp-crd.dtb
dtb-$(CONFIG_ARCH_QCOM) += sdm630-sony-xperia-ganges-kirin.dtb
dtb-$(CONFIG_ARCH_QCOM) += sdm630-sony-xperia-nile-discovery.dtb
dtb-$(CONFIG_ARCH_QCOM) += sdm630-sony-xperia-nile-pioneer.dtb
diff --git a/arch/arm64/boot/dts/qcom/sc8280xp-crd.dts b/arch/arm64/boot/dts/qcom/sc8280xp-crd.dts
new file mode 100644
index 000000000000..1031ee039107
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc8280xp-crd.dts
@@ -0,0 +1,423 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2022, Linaro Limited
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/gpio-keys.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+
+#include "sc8280xp.dtsi"
+#include "sc8280xp-pmics.dtsi"
+
+/ {
+ model = "Qualcomm SC8280XP CRD";
+ compatible = "qcom,sc8280xp-crd", "qcom,sc8280xp";
+
+ aliases {
+ serial0 = &qup2_uart17;
+ };
+
+ backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pmc8280c_lpg 3 1000000>;
+ enable-gpios = <&pmc8280_1_gpios 8 GPIO_ACTIVE_HIGH>;
+ power-supply = <&vreg_edp_bl>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&edp_bl_en>, <&edp_bl_pwm>;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ vreg_edp_bl: edp-bl-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "VREG_EDP_BL";
+
+ regulator-min-microvolt = <3600000>;
+ regulator-max-microvolt = <3600000>;
+
+ gpio = <&pmc8280_1_gpios 9 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&edp_bl_reg_en>;
+
+ regulator-boot-on;
+ };
+
+ vreg_misc_3p3: misc-3p3-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "VREG_MISC_3P3";
+
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&pmc8280_1_gpios 0 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ pinctrl-names = "default";
+ pinctrl-0 = <&misc_3p3_reg_en>;
+
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reserved-memory {
+ };
+};
+
+&apps_rsc {
+ pmc8280-1-rpmh-regulators {
+ compatible = "qcom,pm8350-rpmh-regulators";
+ qcom,pmic-id = "b";
+
+ vdd-l3-l5-supply = <&vreg_s11b>;
+
+ vreg_s11b: smps11 {
+ regulator-name = "vreg_s11b";
+ regulator-min-microvolt = <1272000>;
+ regulator-max-microvolt = <1272000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3b: ldo3 {
+ regulator-name = "vreg_l3b";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vreg_l4b: ldo4 {
+ regulator-name = "vreg_l4b";
+ regulator-min-microvolt = <912000>;
+ regulator-max-microvolt = <912000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ };
+
+ vreg_l6b: ldo6 {
+ regulator-name = "vreg_l6b";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <880000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-boot-on;
+ };
+ };
+
+ pmc8280c-rpmh-regulators {
+ compatible = "qcom,pm8350c-rpmh-regulators";
+ qcom,pmic-id = "c";
+
+ vreg_l1c: ldo1 {
+ regulator-name = "vreg_l1c";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ };
+
+ vreg_l7c: ldo7 {
+ regulator-name = "vreg_l7c";
+ regulator-min-microvolt = <2504000>;
+ regulator-max-microvolt = <2504000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ };
+
+ vreg_l13c: ldo13 {
+ regulator-name = "vreg_l13c";
+ regulator-min-microvolt = <3072000>;
+ regulator-max-microvolt = <3072000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ };
+ };
+
+ pmc8280-2-rpmh-regulators {
+ compatible = "qcom,pm8350-rpmh-regulators";
+ qcom,pmic-id = "d";
+
+ vdd-l1-l4-supply = <&vreg_s11b>;
+
+ vreg_l3d: ldo3 {
+ regulator-name = "vreg_l3d";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ };
+
+ vreg_l4d: ldo4 {
+ regulator-name = "vreg_l4d";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ };
+
+ vreg_l6d: ldo6 {
+ regulator-name = "vreg_l6d";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <880000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ };
+
+ vreg_l7d: ldo7 {
+ regulator-name = "vreg_l7d";
+ regulator-min-microvolt = <3072000>;
+ regulator-max-microvolt = <3072000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ };
+
+ vreg_l9d: ldo9 {
+ regulator-name = "vreg_l9d";
+ regulator-min-microvolt = <912000>;
+ regulator-max-microvolt = <912000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ };
+ };
+
+};
+
+&pmc8280c_lpg {
+ status = "okay";
+};
+
+&pmk8280_pon_pwrkey {
+ status = "okay";
+};
+
+&qup0 {
+ status = "okay";
+};
+
+&qup0_i2c4 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup0_i2c4_default>, <&ts0_default>;
+
+ hid@10 {
+ compatible = "hid-over-i2c";
+ reg = <0x10>;
+ hid-descr-addr = <0x1>;
+
+ interrupts-extended = <&tlmm 175 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+&qup1 {
+ status = "okay";
+};
+
+&qup2 {
+ status = "okay";
+};
+
+&qup2_i2c5 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup2_i2c5_default>, <&kybd_default>, <&tpad_default>;
+
+ hid@15 {
+ compatible = "hid-over-i2c";
+ reg = <0x15>;
+ hid-descr-addr = <0x1>;
+
+ interrupts-extended = <&tlmm 182 IRQ_TYPE_LEVEL_LOW>;
+ };
+
+ hid@68 {
+ compatible = "hid-over-i2c";
+ reg = <0x68>;
+ hid-descr-addr = <0x1>;
+
+ interrupts-extended = <&tlmm 104 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+&qup2_uart17 {
+ compatible = "qcom,geni-debug-uart";
+ status = "okay";
+};
+
+&remoteproc_adsp {
+ status = "okay";
+ firmware-name = "qcom/sc8280xp/qcadsp8280.mbn";
+};
+
+&remoteproc_nsp0 {
+ status = "okay";
+ firmware-name = "qcom/sc8280xp/qccdsp8280.mbn";
+};
+
+&ufs_mem_hc {
+ status = "okay";
+
+ reset-gpios = <&tlmm 228 GPIO_ACTIVE_LOW>;
+
+ vcc-supply = <&vreg_l7c>;
+ vcc-max-microamp = <800000>;
+ vccq-supply = <&vreg_l3d>;
+ vccq-max-microamp = <900000>;
+};
+
+&ufs_mem_phy {
+ status = "okay";
+
+ vdda-phy-supply = <&vreg_l6b>;
+ vdda-pll-supply = <&vreg_l3b>;
+};
+
+&usb_0 {
+ status = "okay";
+};
+
+&usb_0_dwc3 {
+ /* TODO: Define USB-C connector properly */
+ dr_mode = "host";
+};
+
+&usb_0_hsphy {
+ status = "okay";
+
+ vdda-pll-supply = <&vreg_l9d>;
+ vdda18-supply = <&vreg_l1c>;
+ vdda33-supply = <&vreg_l7d>;
+};
+
+&usb_0_qmpphy {
+ status = "okay";
+
+ vdda-phy-supply = <&vreg_l9d>;
+ vdda-pll-supply = <&vreg_l4d>;
+};
+
+&usb_1 {
+ status = "okay";
+};
+
+&usb_1_dwc3 {
+ /* TODO: Define USB-C connector properly */
+ dr_mode = "host";
+};
+
+&usb_1_hsphy {
+ status = "okay";
+
+ vdda-pll-supply = <&vreg_l4b>;
+ vdda18-supply = <&vreg_l1c>;
+ vdda33-supply = <&vreg_l13c>;
+};
+
+&usb_1_qmpphy {
+ status = "okay";
+
+ vdda-phy-supply = <&vreg_l4b>;
+ vdda-pll-supply = <&vreg_l3b>;
+};
+
+/* PINCTRL - additions to nodes defined in sc8280xp.dtsi */
+
+&pmc8280_1_gpios {
+ edp_bl_en: edp-bl-en-state {
+ pins = "gpio8";
+ function = "normal";
+ };
+
+ edp_bl_reg_en: edp-bl-reg-en-state {
+ pins = "gpio9";
+ function = "normal";
+ };
+
+ misc_3p3_reg_en: misc-3p3-reg-en-state {
+ pins = "gpio1";
+ function = "normal";
+ };
+};
+
+&pmc8280c_gpios {
+ edp_bl_pwm: edp-bl-pwm-state {
+ pins = "gpio8";
+ function = "func1";
+ };
+};
+
+&tlmm {
+ gpio-reserved-ranges = <74 6>, <83 4>, <125 2>, <128 2>, <154 7>;
+
+ kybd_default: kybd-default-state {
+ disable {
+ pins = "gpio102";
+ function = "gpio";
+ output-low;
+ };
+
+ int-n {
+ pins = "gpio104";
+ function = "gpio";
+ bias-disable;
+ };
+
+ reset {
+ pins = "gpio105";
+ function = "gpio";
+ bias-disable;
+ };
+ };
+
+ qup0_i2c4_default: qup0-i2c4-default-state {
+ pins = "gpio171", "gpio172";
+ function = "qup4";
+
+ bias-disable;
+ drive-strength = <16>;
+ };
+
+ qup2_i2c5_default: qup2-i2c5-default-state {
+ pins = "gpio81", "gpio82";
+ function = "qup21";
+
+ bias-disable;
+ drive-strength = <16>;
+ };
+
+ tpad_default: tpad-default-state {
+ int-n {
+ pins = "gpio182";
+ function = "gpio";
+ bias-disable;
+ };
+ };
+
+ ts0_default: ts0-default-state {
+ int-n {
+ pins = "gpio175";
+ function = "gpio";
+ bias-pull-up;
+ };
+
+ reset-n {
+ pins = "gpio99";
+ function = "gpio";
+ output-high;
+ drive-strength = <16>;
+ };
+ };
+};
diff --git a/arch/arm64/boot/dts/qcom/sc8280xp-pmics.dtsi b/arch/arm64/boot/dts/qcom/sc8280xp-pmics.dtsi
new file mode 100644
index 000000000000..36ed7d808ab8
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc8280xp-pmics.dtsi
@@ -0,0 +1,108 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2022, Linaro Limited
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/spmi/spmi.h>
+
+&spmi_bus {
+ pmk8280: pmic@0 {
+ compatible = "qcom,pmk8350", "qcom,spmi-pmic";
+ reg = <0x0 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pmk8280_pon: pon@1300 {
+ compatible = "qcom,pm8998-pon";
+ reg = <0x1300>;
+
+ pmk8280_pon_pwrkey: pwrkey {
+ compatible = "qcom,pmk8350-pwrkey";
+ interrupts = <0x0 0x13 0x7 IRQ_TYPE_EDGE_BOTH>;
+ linux,code = <KEY_POWER>;
+ status = "disabled";
+ };
+ };
+ };
+
+ pmc8280_1: pmic@1 {
+ compatible = "qcom,pm8350", "qcom,spmi-pmic";
+ reg = <0x1 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pmc8280_1_gpios: gpio@8800 {
+ compatible = "qcom,pm8350-gpio", "qcom,spmi-gpio";
+ reg = <0x8800>;
+ gpio-controller;
+ gpio-ranges = <&pmc8280_1_gpios 0 0 10>;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
+ pmc8280c: pmic@2 {
+ compatible = "qcom,pm8350c", "qcom,spmi-pmic";
+ reg = <0x2 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pmc8280c_gpios: gpio@8800 {
+ compatible = "qcom,pm8350c-gpio", "qcom,spmi-gpio";
+ reg = <0x8800>;
+ gpio-controller;
+ gpio-ranges = <&pmc8280c_gpios 0 0 9>;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ pmc8280c_lpg: lpg@e800 {
+ compatible = "qcom,pm8350c-pwm";
+ reg = <0xe800>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ #pwm-cells = <2>;
+
+ status = "disabled";
+ };
+ };
+
+ pmc8280_2: pmic@3 {
+ compatible = "qcom,pm8350", "qcom,spmi-pmic";
+ reg = <0x3 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pmc8280_2_gpios: gpio@8800 {
+ compatible = "qcom,pm8350-gpio", "qcom,spmi-gpio";
+ reg = <0x8800>;
+ gpio-controller;
+ gpio-ranges = <&pmc8280_2_gpios 0 0 10>;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
+ pmr735a: pmic@4 {
+ compatible = "qcom,pmr735a", "qcom,spmi-pmic";
+ reg = <0x4 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pmr735a_gpios: gpio@8800 {
+ compatible = "qcom,pmr735a-gpio", "qcom,spmi-gpio";
+ reg = <0x8800>;
+ gpio-controller;
+ gpio-ranges = <&pmr735a_gpios 0 0 4>;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+};
--
2.35.1
\
 
 \ /
  Last update: 2022-06-08 04:49    [W:0.199 / U:0.244 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site