lkml.org 
[lkml]   [2022]   [Jun]   [7]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[RESEND PATCH v4 3/6] Input: edt-ft5x06 - set report rate by dts property
Date
It allows to change the M06/M12 default scan rate on driver probing.

Co-developed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>

---

(no changes since v3)

Changes in v3:
- Check the lower and upper limits of the report-rate-hz value
- Convert the M06 report-rate-hz value

drivers/input/touchscreen/edt-ft5x06.c | 30 ++++++++++++++++++++++++++
1 file changed, 30 insertions(+)

diff --git a/drivers/input/touchscreen/edt-ft5x06.c b/drivers/input/touchscreen/edt-ft5x06.c
index 77f061af5c61..843e8b0522f7 100644
--- a/drivers/input/touchscreen/edt-ft5x06.c
+++ b/drivers/input/touchscreen/edt-ft5x06.c
@@ -1084,6 +1084,7 @@ static int edt_ft5x06_ts_probe(struct i2c_client *client,
struct input_dev *input;
unsigned long irq_flags;
int error;
+ u32 report_rate;
char fw_version[EDT_NAME_LEN];

dev_dbg(&client->dev, "probing for EDT FT5x06 I2C\n");
@@ -1213,6 +1214,35 @@ static int edt_ft5x06_ts_probe(struct i2c_client *client,
edt_ft5x06_ts_get_defaults(&client->dev, tsdata);
edt_ft5x06_ts_get_parameters(tsdata);

+ if (tsdata->reg_addr.reg_report_rate != NO_REGISTER &&
+ !of_property_read_u32(client->dev.of_node, "report-rate-hz",
+ &report_rate)) {
+ tsdata->report_rate = report_rate;
+ if (tsdata->version == EDT_M06) {
+ if (report_rate < 30)
+ report_rate = 30;
+ else if (report_rate > 140)
+ report_rate = 140;
+ } else if (report_rate < 1) {
+ report_rate = 1;
+ } else if (report_rate > 255)
+ report_rate = 255;
+
+ if (report_rate != tsdata->report_rate)
+ dev_warn(&client->dev,
+ "report-rate %dHz is unsupported, use %dHz\n",
+ tsdata->report_rate, report_rate);
+
+ if (tsdata->version == EDT_M06)
+ report_rate /= 10;
+
+ tsdata->report_rate = report_rate;
+
+ edt_ft5x06_register_write(tsdata,
+ tsdata->reg_addr.reg_report_rate,
+ tsdata->report_rate);
+ }
+
dev_dbg(&client->dev,
"Model \"%s\", Rev. \"%s\", %dx%d sensors\n",
tsdata->name, fw_version, tsdata->num_x, tsdata->num_y);
--
2.32.0
\
 
 \ /
  Last update: 2022-06-07 11:58    [W:0.076 / U:0.224 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site