lkml.org 
[lkml]   [2022]   [Jun]   [6]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 2/3] staging: r8188eu: remove rtw_usleep_os
On Thu, Jun 02, 2022 at 09:48:06PM +0200, Martin Kaiser wrote:
> Remove the rtw_usleep_os helper function. There are only two callers, both
> of which call rtw_usleep_os(100).
>
> The original code would translate rtw_usleep_os(100) into msleep(1). Using
> msleep for < 20ms is not recommended. Replace the msleep calls with
> usleep_range, based on the explanations in
> Documentation/timers/timers-howto.rst.
>
> Signed-off-by: Martin Kaiser <martin@kaiser.cx>
> ---
> drivers/staging/r8188eu/core/rtw_pwrctrl.c | 2 +-
> drivers/staging/r8188eu/hal/rtl8188e_hal_init.c | 2 +-
> drivers/staging/r8188eu/include/osdep_service.h | 2 --
> drivers/staging/r8188eu/os_dep/osdep_service.c | 8 --------
> 4 files changed, 2 insertions(+), 12 deletions(-)
>
> diff --git a/drivers/staging/r8188eu/core/rtw_pwrctrl.c b/drivers/staging/r8188eu/core/rtw_pwrctrl.c
> index 7b816b824947..11fd05633529 100644
> --- a/drivers/staging/r8188eu/core/rtw_pwrctrl.c
> +++ b/drivers/staging/r8188eu/core/rtw_pwrctrl.c
> @@ -266,7 +266,7 @@ static s32 LPS_RF_ON_check(struct adapter *padapter, u32 delay_ms)
> err = -1;
> break;
> }
> - rtw_usleep_os(100);
> + usleep_range(1000, 1200);

How do you know this is the proper range?

> }
>
> return err;
> diff --git a/drivers/staging/r8188eu/hal/rtl8188e_hal_init.c b/drivers/staging/r8188eu/hal/rtl8188e_hal_init.c
> index e17375a74f17..1aa7d01b67b1 100644
> --- a/drivers/staging/r8188eu/hal/rtl8188e_hal_init.c
> +++ b/drivers/staging/r8188eu/hal/rtl8188e_hal_init.c
> @@ -208,7 +208,7 @@ static void efuse_read_phymap_from_txpktbuf(
> rtw_write8(adapter, REG_TXPKTBUF_DBG, 0);
> timeout = jiffies + msecs_to_jiffies(1000);
> while (!rtw_read8(adapter, REG_TXPKTBUF_DBG) && time_before(jiffies, timeout))
> - rtw_usleep_os(100);
> + usleep_range(1000, 1200);

Same here, how do you know this is the correct range?

I would just use msleep as needed and later change to a range if you
have figured out that is allowed.

thanks,

greg k-h

\
 
 \ /
  Last update: 2022-06-06 08:06    [W:0.984 / U:1.532 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site