lkml.org 
[lkml]   [2022]   [Jun]   [6]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH] dt-bindings: remoteproc: qcom: q6v5: fix example
Date
Use the node in the examples that is present in msm8974.dtsi, which uses
proper flags for the interrupts and add required 'xo' clock among
others.

Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
---
.../bindings/remoteproc/qcom,q6v5.txt | 41 +++++++++++--------
1 file changed, 23 insertions(+), 18 deletions(-)

diff --git a/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt b/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt
index b677900b3aae..f861862b9770 100644
--- a/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt
+++ b/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt
@@ -257,29 +257,23 @@ related to the Hexagon. See ../soc/qcom/qcom,smd.yaml and
The following example describes the resources needed to boot control the
Hexagon, as it is found on MSM8974 boards.

- modem-rproc@fc880000 {
- compatible = "qcom,q6v5-pil";
- reg = <0xfc880000 0x100>,
- <0xfc820000 0x020>;
+ remoteproc@fc880000 {
+ compatible = "qcom,msm8974-mss-pil";
+ reg = <0xfc880000 0x100>, <0xfc820000 0x020>;
reg-names = "qdsp6", "rmb";

- interrupts-extended = <&intc 0 24 1>,
- <&modem_smp2p_in 0 0>,
- <&modem_smp2p_in 1 0>,
- <&modem_smp2p_in 2 0>,
- <&modem_smp2p_in 3 0>;
- interrupt-names = "wdog",
- "fatal",
- "ready",
- "handover",
- "stop-ack";
+ interrupts-extended = <&intc GIC_SPI 24 IRQ_TYPE_EDGE_RISING>,
+ <&modem_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
+ <&modem_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
+ <&modem_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
+ <&modem_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
+ interrupt-names = "wdog", "fatal", "ready", "handover", "stop-ack";

clocks = <&gcc GCC_MSS_Q6_BIMC_AXI_CLK>,
<&gcc GCC_MSS_CFG_AHB_CLK>,
- <&gcc GCC_BOOT_ROM_AHB_CLK>;
- clock-names = "iface", "bus", "mem";
-
- qcom,halt-regs = <&tcsr_mutex_block 0x1180 0x1200 0x1280>;
+ <&gcc GCC_BOOT_ROM_AHB_CLK>,
+ <&xo_board>;
+ clock-names = "iface", "bus", "mem", "xo";

resets = <&gcc GCC_MSS_RESTART>;
reset-names = "mss_restart";
@@ -289,6 +283,8 @@ Hexagon, as it is found on MSM8974 boards.
mx-supply = <&pm8841_s1>;
pll-supply = <&pm8941_l12>;

+ qcom,halt-regs = <&tcsr_mutex_block 0x1180 0x1200 0x1280>;
+
qcom,smem-states = <&modem_smp2p_out 0>;
qcom,smem-state-names = "stop";

@@ -299,4 +295,13 @@ Hexagon, as it is found on MSM8974 boards.
mpss {
memory-region = <&mpss_region>;
};
+
+ smd-edge {
+ interrupts = <GIC_SPI 25 IRQ_TYPE_EDGE_RISING>;
+
+ qcom,ipc = <&apcs 8 12>;
+ qcom,smd-edge = <0>;
+
+ label = "modem";
+ };
};
--
2.36.1
\
 
 \ /
  Last update: 2022-06-06 15:25    [W:0.048 / U:0.128 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site