lkml.org 
[lkml]   [2022]   [Jun]   [6]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 30/36] serial: fsl_lpuart: Call core's sanitization and remove custom one
Date
Serial core handles serial_rs485 sanitization. Remove custom
sanitization from lpuart_config_rs485.

This change loses dev_err when SER_RS485_RX_DURING_TX is set due to
incorrect configuration. Other drivers do not do similar prinout for
full-duplex case and it should be done in serial core if it is
desirable to notify on this condition. Personally, I doesn't see it
important because the kernel gracefully downgrades to half-duplex.

Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
---
drivers/tty/serial/fsl_lpuart.c | 17 -----------------
1 file changed, 17 deletions(-)

diff --git a/drivers/tty/serial/fsl_lpuart.c b/drivers/tty/serial/fsl_lpuart.c
index 88692dc9eefa..d35414cb3e4e 100644
--- a/drivers/tty/serial/fsl_lpuart.c
+++ b/drivers/tty/serial/fsl_lpuart.c
@@ -1365,11 +1365,6 @@ static int lpuart_config_rs485(struct uart_port *port,
~(UARTMODEM_TXRTSPOL | UARTMODEM_TXRTSE);
writeb(modem, sport->port.membase + UARTMODEM);

- /* clear unsupported configurations */
- rs485->delay_rts_before_send = 0;
- rs485->delay_rts_after_send = 0;
- rs485->flags &= ~SER_RS485_RX_DURING_TX;
-
if (rs485->flags & SER_RS485_ENABLED) {
/* Enable auto RS-485 RTS mode */
modem |= UARTMODEM_TXRTSE;
@@ -1400,11 +1395,6 @@ static int lpuart32_config_rs485(struct uart_port *port,
& ~(UARTMODEM_TXRTSPOL | UARTMODEM_TXRTSE);
lpuart32_write(&sport->port, modem, UARTMODIR);

- /* clear unsupported configurations */
- rs485->delay_rts_before_send = 0;
- rs485->delay_rts_after_send = 0;
- rs485->flags &= ~SER_RS485_RX_DURING_TX;
-
if (rs485->flags & SER_RS485_ENABLED) {
/* Enable auto RS-485 RTS mode */
modem |= UARTMODEM_TXRTSE;
@@ -2723,13 +2713,6 @@ static int lpuart_probe(struct platform_device *pdev)
if (ret)
goto failed_get_rs485;

- if (sport->port.rs485.flags & SER_RS485_RX_DURING_TX)
- dev_err(&pdev->dev, "driver doesn't support RX during TX\n");
-
- if (sport->port.rs485.delay_rts_before_send ||
- sport->port.rs485.delay_rts_after_send)
- dev_err(&pdev->dev, "driver doesn't support RTS delays\n");
-
uart_rs485_config(&sport->port);

ret = devm_request_irq(&pdev->dev, sport->port.irq, handler, 0,
--
2.30.2
\
 
 \ /
  Last update: 2022-06-06 12:10    [W:0.441 / U:0.020 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site