lkml.org 
[lkml]   [2022]   [Jun]   [5]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v2 1/3] dt-bindings: leds: Add bindings for the TLC5925 controller
On Fri, Jun 03, 2022 at 05:53:30PM +0200, Jean-Jacques Hiblot wrote:
> Add bindings documentation for the TLC5925 LED controller.
>
> Signed-off-by: Jean-Jacques Hiblot <jjhiblot@traphandler.com>
> ---
> .../devicetree/bindings/leds/ti,tlc5925.yaml | 106 ++++++++++++++++++
> 1 file changed, 106 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/leds/ti,tlc5925.yaml
>
> diff --git a/Documentation/devicetree/bindings/leds/ti,tlc5925.yaml b/Documentation/devicetree/bindings/leds/ti,tlc5925.yaml
> new file mode 100644
> index 000000000000..379ade094fd3
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/leds/ti,tlc5925.yaml
> @@ -0,0 +1,106 @@
> +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/leds/ti,tlc5925.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: LEDs connected to TI TLC5925 controller
> +
> +maintainers:
> + - Jean-Jacques Hiblot <jjhiblot@traphandler.com>
> +
> +description: |
> + The TLC5925 is a low-power 16-channel constant-current LED sink driver.
> + It is controlled through a SPI interface.
> + It is built around a shift register and latches which convert serial
> + input data into a parallel output. Several TLC5925 can be chained to
> + control more than 16 LEDs with a single chip-select.
> + The brightness level cannot be controlled, each LED is either on or off.
> +
> + Each LED is represented as a sub-node of the ti,tlc5925 device.
> +
> +$ref: /schemas/spi/spi-peripheral-props.yaml#
> +
> +properties:
> + compatible:
> + const: ti,tlc5925
> +
> + shift-register-length:

Not a common property. Needs a vendor prefix and type.

> + minimum: 8
> + description: |
> + The length of the shift register. If several TLC5925 are chained,
> + shift_register_length should be set to 16 times the number of TLC5925.
> + The value must be a multiple of 8.
> +
> + "#address-cells":
> + const: 1
> +
> + "#size-cells":
> + const: 0
> +
> + output-enable-b-gpios:
> + description: |
> + Optional GPIO pins to enable/disable the parallel output. They describe
> + the GPIOs connected to the OE/ pin of the TLC5925s.
> +
> +patternProperties:
> + "@[0-9a-z]+$":

Unit addresses are typically hex (a-f).

> + type: object
> + $ref: common.yaml#
> +
> + description: |
> + LED pin number (must be lower than shift_register_length).
> + The furthest LED down the chain has the pin number 0.
> +
> + properties:
> + reg:
> + minimum: 0

0 is always the minimum.

> +
> + required:
> + - reg
> +
> +additionalProperties: true

Not allowed except for common schemas. Must be false. Since you have a
$ref, you probably want 'unevaluatedProperties: false' instead.


> +
> +required:
> + - "#address-cells"
> + - "#size-cells"
> + - shift_register_length
> +
> +examples:
> + - |
> + #include <dt-bindings/gpio/gpio.h>
> + #include <dt-bindings/leds/common.h>
> +
> + spi0 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + leds@2 {
> + compatible = "ti,tlc5925";
> + reg = <0x02>;
> + spi-max-frequency = <30000000>;
> + shift_register_length = <32>;
> + output-enable-b-gpios = <&gpio0b 9 GPIO_ACTIVE_HIGH>, <&gpio0b 7 GPIO_ACTIVE_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + led@0 {
> + reg = <0>;
> + function = LED_FUNCTION_STATUS;
> + color = <LED_COLOR_ID_GREEN>;
> + };
> +
> + led@4 {
> + reg = <4>;
> + function = LED_FUNCTION_STATUS;
> + color = <LED_COLOR_ID_RED>;
> + };
> +
> + led@1f {
> + reg = <31>;
> + function = LED_FUNCTION_PANIC;
> + color = <LED_COLOR_ID_RED>;
> + };
> + };
> +
> + };
> --
> 2.25.1
>
>

\
 
 \ /
  Last update: 2022-06-06 01:01    [W:0.047 / U:0.776 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site