lkml.org 
[lkml]   [2022]   [Jun]   [28]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH 12/12] habanalabs: enable gaudi2 code in driver
On Tue, Jun 28, 2022 at 9:29 AM Greg KH <gregkh@linuxfoundation.org> wrote:
>
> On Mon, Jun 27, 2022 at 11:26:20PM +0300, Oded Gabbay wrote:
> > Enable the Gaudi2 ASIC code in the pci probe callback of the driver so
> > the driver will handle Gaudi2 ASICs.
> >
> > Add the PCI ID to the PCI table and add the ASIC enum value to all
> > relevant places.
> >
> > Fixup the device parameters initialization for Gaudi2.
> >
> > Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
> > ---
> > drivers/misc/habanalabs/common/device.c | 8 +++
> > drivers/misc/habanalabs/common/habanalabs.h | 13 ++--
> > .../misc/habanalabs/common/habanalabs_drv.c | 67 +++++++++++++++----
> > drivers/misc/habanalabs/common/sysfs.c | 6 ++
> > 4 files changed, 77 insertions(+), 17 deletions(-)
> >
> > diff --git a/drivers/misc/habanalabs/common/device.c b/drivers/misc/habanalabs/common/device.c
> > index 38cf2f1659ee..a4656eac495e 100644
> > --- a/drivers/misc/habanalabs/common/device.c
> > +++ b/drivers/misc/habanalabs/common/device.c
> > @@ -645,6 +645,14 @@ static int device_early_init(struct hl_device *hdev)
> > gaudi_set_asic_funcs(hdev);
> > strscpy(hdev->asic_name, "GAUDI SEC", sizeof(hdev->asic_name));
> > break;
> > + case ASIC_GAUDI2:
> > + gaudi2_set_asic_funcs(hdev);
> > + strscpy(hdev->asic_name, "GAUDI2", sizeof(hdev->asic_name));
> > + break;
> > + case ASIC_GAUDI2_SEC:
> > + gaudi2_set_asic_funcs(hdev);
> > + strscpy(hdev->asic_name, "GAUDI2 SEC", sizeof(hdev->asic_name));
> > + break;
> > default:
> > dev_err(hdev->dev, "Unrecognized ASIC type %d\n",
> > hdev->asic_type);
> > diff --git a/drivers/misc/habanalabs/common/habanalabs.h b/drivers/misc/habanalabs/common/habanalabs.h
> > index 4537845658f8..587b1c537115 100644
> > --- a/drivers/misc/habanalabs/common/habanalabs.h
> > +++ b/drivers/misc/habanalabs/common/habanalabs.h
> > @@ -3033,7 +3033,6 @@ struct hl_reset_info {
> > * @disabled: is device disabled.
> > * @late_init_done: is late init stage was done during initialization.
> > * @hwmon_initialized: is H/W monitor sensors was initialized.
> > - * @heartbeat: is heartbeat sanity check towards CPU-CP enabled.
>
> You remove this field, but you still keep it in the structure, you just
> move it later down to the bottom for some reason:
>
> > * @reset_on_lockup: true if a reset should be done in case of stuck CS, false
> > * otherwise.
> > * @dram_default_page_mapping: is DRAM default page mapping enabled.
> > @@ -3066,6 +3065,10 @@ struct hl_reset_info {
> > * @is_compute_ctx_active: Whether there is an active compute context executing.
> > * @compute_ctx_in_release: true if the current compute context is being released.
> > * @supports_mmu_prefetch: true if prefetch is supported, otherwise false.
> > + * @reset_upon_device_release: reset the device when the user closes the file descriptor of the
> > + * device.
> > + * @skip_iatu_for_unsecured_device: skip the device PCI controller initialization when working
> > + * with device that runs f/w that is not secured.
> > */
> > struct hl_device {
> > struct pci_dev *pdev;
> > @@ -3175,7 +3178,6 @@ struct hl_device {
> > u8 disabled;
> > u8 late_init_done;
> > u8 hwmon_initialized;
> > - u8 heartbeat;
> > u8 reset_on_lockup;
> > u8 dram_default_page_mapping;
> > u8 memory_scrub;
> > @@ -3199,6 +3201,8 @@ struct hl_device {
> > u8 is_compute_ctx_active;
> > u8 compute_ctx_in_release;
> > u8 supports_mmu_prefetch;
> > + u8 reset_upon_device_release;
> > + u8 skip_iatu_for_unsecured_device;
> >
> > /* Parameters for bring-up */
> > u64 nic_ports_mask;
> > @@ -3212,11 +3216,9 @@ struct hl_device {
> > u8 dram_scrambler_enable;
> > u8 hard_reset_on_fw_events;
> > u8 bmc_enable;
> > - u8 rl_enable;
> > u8 reset_on_preboot_fail;
> > - u8 reset_upon_device_release;
> > - u8 skip_iatu_for_unsecured_device;
> > u8 reset_if_device_not_idle;
> > + u8 heartbeat;
> > };
>
> Did you mean to do that?
>
> thanks,
>
> greg k-h

Yes, I meant to do that. There are (currently) 13 variables under the
comment of "bring-up" parameters.
These parameters are used all over our code and in our internal
package we expose them as kernel module parameters for us to play with
to help with bring-ups and testing on palladium.
But in the upstream driver, I just set them to fixed values and I
remove the comments as I don't want anyone to play with them. And of
course I don't expose them as kernel params.

The alternative is to remove their usage from all over the code but
this will create for me a serious headache when taking patches and
upstreaming them, because the code will be very different from our
internal development tree.

After I explained all the above, I think I'll just add the comments
anyway, to make this documentation complete. I hope this will remove
any future confusion.

Thanks,
Oded

\
 
 \ /
  Last update: 2022-06-28 09:07    [W:0.795 / U:0.268 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site