lkml.org 
[lkml]   [2022]   [Jun]   [28]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH] serial: 8250: Fix PM usage_count for console handover
On Tue, Jun 28, 2022 at 07:58:34PM +0300, Ilpo Järvinen wrote:
> When console is enabled, univ8250_console_setup() calls
> serial8250_console_setup() before .dev is set to uart_port. Therefore,
> it will not call pm_runtime_get_sync(). Later, when the actual driver
> is going to take over univ8250_console_exit() is called. As .dev is
> already set, serial8250_console_exit() makes pm_runtime_put_sync() call
> with usage count being zero triggering PM usage count warning
> (extra debug for univ8250_console_setup(), univ8250_console_exit(), and
> serial8250_register_ports()):
>
> [ 0.068987] univ8250_console_setup ttyS0 nodev
> [ 0.499670] printk: console [ttyS0] enabled
> [ 0.717955] printk: console [ttyS0] printing thread started
> [ 1.960163] serial8250_register_ports assigned dev for ttyS0
> [ 1.976830] printk: console [ttyS0] disabled
> [ 1.976888] printk: console [ttyS0] printing thread stopped
> [ 1.977073] univ8250_console_exit ttyS0 usage:0
> [ 1.977075] serial8250 serial8250: Runtime PM usage count underflow!
> [ 1.977429] dw-apb-uart.6: ttyS0 at MMIO 0x4010006000 (irq = 33, base_baud = 115200) is a 16550A
> [ 1.977812] univ8250_console_setup ttyS0 usage:2
> [ 1.978167] printk: console [ttyS0] printing thread started
> [ 1.978203] printk: console [ttyS0] enabled
>
> To fix the issue, call pm_runtime_get_sync() in
> serial8250_register_ports() as soon as .dev is set for an uart_port
> if it has console enabled.
>
> This problem became apparent only recently because 82586a721595 ("PM:
> runtime: Avoid device usage count underflows") added the warning
> printout. I confirmed this problem also occurs with v5.18 (w/o the
> warning printout, obviously) so the recent printk kthreads are not the
> cause for this.

Since printk kthread was reverted, you may drop its mention here completely.

In any case, good catch!
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

But it would be good to be tested by Tony.

> Fixes: bedb404e91bb ("serial: 8250_port: Don't use power management for kernel console")
> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
>
> ---
> drivers/tty/serial/8250/8250_core.c | 4 ++++
> drivers/tty/serial/serial_core.c | 5 -----
> include/linux/serial_core.h | 5 +++++
> 3 files changed, 9 insertions(+), 5 deletions(-)
>
> diff --git a/drivers/tty/serial/8250/8250_core.c b/drivers/tty/serial/8250/8250_core.c
> index 57e86133af4f..2e83e7367441 100644
> --- a/drivers/tty/serial/8250/8250_core.c
> +++ b/drivers/tty/serial/8250/8250_core.c
> @@ -23,6 +23,7 @@
> #include <linux/sysrq.h>
> #include <linux/delay.h>
> #include <linux/platform_device.h>
> +#include <linux/pm_runtime.h>
> #include <linux/tty.h>
> #include <linux/ratelimit.h>
> #include <linux/tty_flip.h>
> @@ -558,6 +559,9 @@ serial8250_register_ports(struct uart_driver *drv, struct device *dev)
>
> up->port.dev = dev;
>
> + if (uart_console_enabled(&up->port))
> + pm_runtime_get_sync(up->port.dev);
> +
> serial8250_apply_quirks(up);
> uart_add_one_port(drv, &up->port);
> }
> diff --git a/drivers/tty/serial/serial_core.c b/drivers/tty/serial/serial_core.c
> index 85ef7ef00b82..3161445504bc 100644
> --- a/drivers/tty/serial/serial_core.c
> +++ b/drivers/tty/serial/serial_core.c
> @@ -2024,11 +2024,6 @@ static int uart_proc_show(struct seq_file *m, void *v)
> }
> #endif
>
> -static inline bool uart_console_enabled(struct uart_port *port)
> -{
> - return uart_console(port) && (port->cons->flags & CON_ENABLED);
> -}
> -
> static void uart_port_spin_lock_init(struct uart_port *port)
> {
> spin_lock_init(&port->lock);
> diff --git a/include/linux/serial_core.h b/include/linux/serial_core.h
> index b7b86ee3cb12..9d8aa139b175 100644
> --- a/include/linux/serial_core.h
> +++ b/include/linux/serial_core.h
> @@ -404,6 +404,11 @@ static const bool earlycon_acpi_spcr_enable EARLYCON_USED_OR_UNUSED;
> static inline int setup_earlycon(char *buf) { return 0; }
> #endif
>
> +static inline bool uart_console_enabled(struct uart_port *port)
> +{
> + return uart_console(port) && (port->cons->flags & CON_ENABLED);
> +}
> +
> struct uart_port *uart_get_console(struct uart_port *ports, int nr,
> struct console *c);
> int uart_parse_earlycon(char *p, unsigned char *iotype, resource_size_t *addr,
>
> --
> tg: (f287f971e256..) fix/console-usage_count (depends on: tty-next)

--
With Best Regards,
Andy Shevchenko


\
 
 \ /
  Last update: 2022-06-28 23:14    [W:0.061 / U:0.204 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site