lkml.org 
[lkml]   [2022]   [Jun]   [27]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 7/7] media: dt-bindings: ov5693: document YAML binding
Hi Krzysztof,
Thanks for your review, I will fix this in v2.

Regards,
Tommaso

On Sat, Jun 25, 2022 at 10:35:50PM +0200, Krzysztof Kozlowski wrote:
> On 25/06/2022 01:03, Tommaso Merciai wrote:
> > This patch adds documentation of device tree in YAML schema for the
> > OV5693 CMOS image sensor from Omnivision
> >
> > Signed-off-by: Tommaso Merciai <tommaso.merciai@amarulasolutions.com>
> > ---
> > .../bindings/media/i2c/ovti,ov5693.yaml | 123 ++++++++++++++++++
> > MAINTAINERS | 1 +
> > 2 files changed, 124 insertions(+)
> > create mode 100644 Documentation/devicetree/bindings/media/i2c/ovti,ov5693.yaml
> >
> > diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov5693.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov5693.yaml
> > new file mode 100644
> > index 000000000000..1ee70af40000
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov5693.yaml
> > @@ -0,0 +1,123 @@
> > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> > +# Copyright (c) 2022 Amarulasolutions
> > +%YAML 1.2
> > +---
> > +$id: http://devicetree.org/schemas/media/i2c/ovti,ov5693.yaml#
> > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > +
> > +title: Omnivision OV5693 CMOS Sensor
> > +
> > +maintainers:
> > + - Tommaso Merciai <tommaso.merciai@amarulasolutions.com>
> > +
> > +allOf:
> > + - $ref: /schemas/media/video-interface-devices.yaml#
>
> This goes after description.
>
> > +
> > +description: |
> > + The Omnivision OV5693 is a high performance, 1/4-inch, 5 megapixel, CMOS
> > + image sensor that delivers 2592x1944 at 30fps. It provides full-frame,
> > + sub-sampled, and windowed 10-bit MIPI images in various formats via the
> > + Serial Camera Control Bus (SCCB) interface.
> > +
> > + Supports images sizes: 5 Mpixel, EIS1080p, 1080p, 720p, VGA, QVGA
> > +
> > + OV5693 is programmable through I2C and two-wire Serial Camera Control Bus (SCCB).
> > + The sensor output is available via CSI-2 serial data output (up to 2-lane).
> > +
> > +properties:
> > + compatible:
> > + const: ovti,ov5693
> > +
> > + reg:
> > + maxItems: 1
> > +
> > + clocks:
> > + description:
> > + System input clock (aka XVCLK). From 6 to 27 MHz.
> > + maxItems: 1
> > +
> > + dovdd-supply:
> > + description:
> > + Digital I/O voltage supply, 1.8V.
> > +
> > + avdd-supply:
> > + description:
> > + Analog voltage supply, 2.8V.
> > +
> > + dvdd-supply:
> > + description:
> > + Digital core voltage supply, 1.2V.
> > +
> > + reset-gpios:
> > + description:
> > + The phandle and specifier for the GPIO that controls sensor reset.
> > + This corresponds to the hardware pin XSHUTDN which is physically
> > + active low.
> > + maxItems: 1
> > +
> > + port:
> > + $ref: /schemas/graph.yaml#/$defs/port-base
> > + additionalProperties: false
> > +
> > + properties:
> > + endpoint:
> > + $ref: /schemas/media/video-interfaces.yaml#
> > + unevaluatedProperties: false
> > +
> > + properties:
> > + data-lanes:
> > + minItems: 1
> > + maxItems: 2
> > +
> > + # Supports max data transfer of 900 Mbps per lane
> > + link-frequencies: true
>
> This is not needed. Provided by video-interfaces.yaml.
>
> > +
> > +required:
> > + - compatible
> > + - reg
> > + - clocks
> > + - dovdd-supply
> > + - avdd-supply
> > + - dvdd-supply
> > + - port
> > +
> > +unevaluatedProperties: false
> > +
> > +examples:
> > + - |
> > + #include <dt-bindings/clock/px30-cru.h>
> > + #include <dt-bindings/gpio/gpio.h>
> > + #include <dt-bindings/pinctrl/rockchip.h>
> > +
> > + i2c {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + ov5693: camera@36 {
> > + compatible = "ovti,ov5693";
> > + reg = <0x36>;
> > +
> > + reset-gpios = <&gpio2 RK_PB1 GPIO_ACTIVE_LOW>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&cif_clkout_m0>;
> > +
> > + clocks = <&cru SCLK_CIF_OUT>;
> > + assigned-clocks = <&cru SCLK_CIF_OUT>;
> > + assigned-clock-rates = <19200000>;
> > +
> > + avdd-supply = <&vcc_1v8>;
> > + dvdd-supply = <&vcc_1v2>;
> > + dovdd-supply = <&vcc_2v8>;
> > +
> > + rotation = <90>;
> > + orientation = <0>;
> > +
> > + port {
> > + ucam_out: endpoint {
> > + remote-endpoint = <&mipi_in_ucam>;
> > + data-lanes = <1 2>;
> > + link-frequencies = /bits/ 64 <450000000>;
> > + };
> > + };
> > + };
> > + };
> > \ No newline at end of file
>
> ^^^ This has to be fixed.
>
> > diff --git a/MAINTAINERS b/MAINTAINERS
> Best regards,
> Krzysztof

--
Tommaso Merciai
Embedded Linux Engineer
tommaso.merciai@amarulasolutions.com
__________________________________

Amarula Solutions SRL
Via Le Canevare 30, 31100 Treviso, Veneto, IT
T. +39 042 243 5310
info@amarulasolutions.com
www.amarulasolutions.com

\
 
 \ /
  Last update: 2022-06-27 10:03    [W:0.113 / U:0.044 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site