lkml.org 
[lkml]   [2022]   [Jun]   [22]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
SubjectRe: [PATCH v2 4/6] arm64: dts: qcom: sc8280xp: Add reference device
From


On 22.06.2022 06:12, Bjorn Andersson wrote:
> Add basic support for the SC8280XP reference device, which allows it to
> boot to a shell (using EFIFB) with functional storage (UFS), USB,
> keyboard, touchpad, touchscreen, backlight and remoteprocs.
>
> The PMICs are, per socinfo, reused from other platforms. But given that
> the address of the PMICs doesn't match other cases and that it's
> desirable to label things according to the schematics a new dtsi file is
> created to represent the reference combination of PMICs.
>
> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
> Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
> ---
>
> Changes since v1:
> - Reordered "status" last
> - Fixed invalid PMIC gpio 0
> - Replaced "hid" name with touchscreen, touchpad and keyboard
> - Added &xo_board_clk frequency
>
> arch/arm64/boot/dts/qcom/Makefile | 1 +
> arch/arm64/boot/dts/qcom/sc8280xp-crd.dts | 432 +++++++++++++++++++
> arch/arm64/boot/dts/qcom/sc8280xp-pmics.dtsi | 108 +++++
> 3 files changed, 541 insertions(+)
> create mode 100644 arch/arm64/boot/dts/qcom/sc8280xp-crd.dts
> create mode 100644 arch/arm64/boot/dts/qcom/sc8280xp-pmics.dtsi
>
> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
> index 2f8aec2cc6db..ceeae094a59f 100644
> --- a/arch/arm64/boot/dts/qcom/Makefile
> +++ b/arch/arm64/boot/dts/qcom/Makefile
> @@ -89,6 +89,7 @@ dtb-$(CONFIG_ARCH_QCOM) += sc7280-herobrine-villager-r0.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sc7280-idp.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sc7280-idp2.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sc7280-crd-r3.dtb
> +dtb-$(CONFIG_ARCH_QCOM) += sc8280xp-crd.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sdm630-sony-xperia-ganges-kirin.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sdm630-sony-xperia-nile-discovery.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sdm630-sony-xperia-nile-pioneer.dtb
> diff --git a/arch/arm64/boot/dts/qcom/sc8280xp-crd.dts b/arch/arm64/boot/dts/qcom/sc8280xp-crd.dts
> new file mode 100644
> index 000000000000..38a64e886466
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/sc8280xp-crd.dts
> @@ -0,0 +1,432 @@
> +// SPDX-License-Identifier: BSD-3-Clause
> +/*
> + * Copyright (c) 2021, The Linux Foundation. All rights reserved.
> + * Copyright (c) 2022, Linaro Limited
> + */
> +
> +/dts-v1/;
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/gpio-keys.h>
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
> +
> +#include "sc8280xp.dtsi"
> +#include "sc8280xp-pmics.dtsi"
> +
> +/ {
> + model = "Qualcomm SC8280XP CRD";
> + compatible = "qcom,sc8280xp-crd", "qcom,sc8280xp";
> +
> + aliases {
> + serial0 = &qup2_uart17;
> + };
> +
> + backlight {
> + compatible = "pwm-backlight";
> + pwms = <&pmc8280c_lpg 3 1000000>;
> + enable-gpios = <&pmc8280_1_gpios 8 GPIO_ACTIVE_HIGH>;
> + power-supply = <&vreg_edp_bl>;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&edp_bl_en>, <&edp_bl_pwm>;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + vreg_edp_bl: edp-bl-regulator {
> + compatible = "regulator-fixed";
> +
> + regulator-name = "VREG_EDP_BL";
> + regulator-min-microvolt = <3600000>;
> + regulator-max-microvolt = <3600000>;
> +
> + gpio = <&pmc8280_1_gpios 9 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&edp_bl_reg_en>;
> +
> + regulator-boot-on;
> + };
> +
> + vreg_misc_3p3: misc-3p3-regulator {
> + compatible = "regulator-fixed";
> +
> + regulator-name = "VREG_MISC_3P3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> +
> + gpio = <&pmc8280_1_gpios 1 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&misc_3p3_reg_en>;
> +
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + reserved-memory {
> + };
Seems redundant.


> +};
> +
> +&apps_rsc {
> + pmc8280-1-rpmh-regulators {
> + compatible = "qcom,pm8350-rpmh-regulators";
> + qcom,pmic-id = "b";
> +
> + vdd-l3-l5-supply = <&vreg_s11b>;
> +
> + vreg_s11b: smps11 {
> + regulator-name = "vreg_s11b";
> + regulator-min-microvolt = <1272000>;
> + regulator-max-microvolt = <1272000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l3b: ldo3 {
> + regulator-name = "vreg_l3b";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + vreg_l4b: ldo4 {
> + regulator-name = "vreg_l4b";
> + regulator-min-microvolt = <912000>;
> + regulator-max-microvolt = <912000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + };
> +
> + vreg_l6b: ldo6 {
> + regulator-name = "vreg_l6b";
> + regulator-min-microvolt = <880000>;
> + regulator-max-microvolt = <880000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-boot-on;
> + };
> + };
> +
> + pmc8280c-rpmh-regulators {
> + compatible = "qcom,pm8350c-rpmh-regulators";
> + qcom,pmic-id = "c";
> +
> + vreg_l1c: ldo1 {
> + regulator-name = "vreg_l1c";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + };
> +
> + vreg_l7c: ldo7 {
> + regulator-name = "vreg_l7c";
> + regulator-min-microvolt = <2504000>;
> + regulator-max-microvolt = <2504000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + };
> +
> + vreg_l13c: ldo13 {
> + regulator-name = "vreg_l13c";
> + regulator-min-microvolt = <3072000>;
> + regulator-max-microvolt = <3072000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + };
> + };
> +
> + pmc8280-2-rpmh-regulators {
> + compatible = "qcom,pm8350-rpmh-regulators";
> + qcom,pmic-id = "d";
> +
> + vdd-l1-l4-supply = <&vreg_s11b>;
> +
> + vreg_l3d: ldo3 {
> + regulator-name = "vreg_l3d";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + };
> +
> + vreg_l4d: ldo4 {
> + regulator-name = "vreg_l4d";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + };
> +
> + vreg_l6d: ldo6 {
> + regulator-name = "vreg_l6d";
> + regulator-min-microvolt = <880000>;
> + regulator-max-microvolt = <880000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + };
> +
> + vreg_l7d: ldo7 {
> + regulator-name = "vreg_l7d";
> + regulator-min-microvolt = <3072000>;
> + regulator-max-microvolt = <3072000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + };
> +
> + vreg_l9d: ldo9 {
> + regulator-name = "vreg_l9d";
> + regulator-min-microvolt = <912000>;
> + regulator-max-microvolt = <912000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + };
> + };
> +};
> +
> +&pmc8280c_lpg {
> + status = "okay";
> +};
> +
> +&pmk8280_pon_pwrkey {
> + status = "okay";
> +};
> +
> +&qup0 {
> + status = "okay";
> +};
> +
> +&qup0_i2c4 {
> + clock-frequency = <400000>;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&qup0_i2c4_default>, <&ts0_default>;
> +
> + status = "okay";
> +
> + touchscreen@10 {
> + compatible = "hid-over-i2c";
> + reg = <0x10>;
> + hid-descr-addr = <0x1>;
> + interrupts-extended = <&tlmm 175 IRQ_TYPE_LEVEL_LOW>;
> + vdd-supply = <&vreg_misc_3p3>;
> + };
> +};
> +
> +&qup1 {
> + status = "okay";
> +};
> +
> +&qup2 {
> + status = "okay";
> +};
> +
> +&qup2_i2c5 {
> + clock-frequency = <400000>;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&qup2_i2c5_default>, <&kybd_default>, <&tpad_default>;
> +
> + status = "okay";
> +
I think all device DTs generally have 'status = "okay"' at the beginning. Should we change that?


> + touchpad@15 {
> + compatible = "hid-over-i2c";
> + reg = <0x15>;
> + hid-descr-addr = <0x1>;
> + interrupts-extended = <&tlmm 182 IRQ_TYPE_LEVEL_LOW>;
> + vdd-supply = <&vreg_misc_3p3>;
> + };
> +
> + keyboard@68 {
> + compatible = "hid-over-i2c";
> + reg = <0x68>;
> + hid-descr-addr = <0x1>;
> + interrupts-extended = <&tlmm 104 IRQ_TYPE_LEVEL_LOW>;
> + vdd-supply = <&vreg_misc_3p3>;
> + };
> +};
> +
> +&qup2_uart17 {
> + compatible = "qcom,geni-debug-uart";
> +
> + status = "okay";
> +};
> +
> +&remoteproc_adsp {
> + firmware-name = "qcom/sc8280xp/qcadsp8280.mbn";
> +
> + status = "okay";
> +};
> +
> +&remoteproc_nsp0 {
> + firmware-name = "qcom/sc8280xp/qccdsp8280.mbn";
> +
> + status = "okay";
> +};
> +
> +&ufs_mem_hc {
> + reset-gpios = <&tlmm 228 GPIO_ACTIVE_LOW>;
> +
> + vcc-supply = <&vreg_l7c>;
> + vcc-max-microamp = <800000>;
> + vccq-supply = <&vreg_l3d>;
> + vccq-max-microamp = <900000>;
> +
> + status = "okay";
> +};
> +
> +&ufs_mem_phy {
> + vdda-phy-supply = <&vreg_l6b>;
> + vdda-pll-supply = <&vreg_l3b>;
> +
> + status = "okay";
> +};
> +
> +&usb_0 {
> + status = "okay";
> +};
> +
> +&usb_0_dwc3 {
> + /* TODO: Define USB-C connector properly */
> + dr_mode = "host";
> +};
> +
> +&usb_0_hsphy {
> + vdda-pll-supply = <&vreg_l9d>;
> + vdda18-supply = <&vreg_l1c>;
> + vdda33-supply = <&vreg_l7d>;
> +
> + status = "okay";
> +};
> +
> +&usb_0_qmpphy {
> + vdda-phy-supply = <&vreg_l9d>;
> + vdda-pll-supply = <&vreg_l4d>;
> +
> + status = "okay";
> +};
> +
> +&usb_1 {
> + status = "okay";
> +};
> +
> +&usb_1_dwc3 {
> + /* TODO: Define USB-C connector properly */
> + dr_mode = "host";
> +};
> +
> +&usb_1_hsphy {
> + vdda-pll-supply = <&vreg_l4b>;
> + vdda18-supply = <&vreg_l1c>;
> + vdda33-supply = <&vreg_l13c>;
> +
> + status = "okay";
> +};
> +
> +&usb_1_qmpphy {
> + vdda-phy-supply = <&vreg_l4b>;
> + vdda-pll-supply = <&vreg_l3b>;
> +
> + status = "okay";
> +};
> +
> +/* PINCTRL - additions to nodes defined in sc8280xp.dtsi */
This comment seems redundant.

> +
> +&pmc8280_1_gpios {
> + edp_bl_en: edp-bl-en-state {
> + pins = "gpio8";
> + function = "normal";
> + };
> +
> + edp_bl_reg_en: edp-bl-reg-en-state {
> + pins = "gpio9";
> + function = "normal";
> + };
> +
> + misc_3p3_reg_en: misc-3p3-reg-en-state {
> + pins = "gpio1";
> + function = "normal";
> + };
> +};
> +
> +&pmc8280c_gpios {
> + edp_bl_pwm: edp-bl-pwm-state {
> + pins = "gpio8";
> + function = "func1";
> + };
> +};
> +
> +&xo_board_clk {
> + clock-frequency = <38400000>;
> +};
> +
> +&tlmm {
> + gpio-reserved-ranges = <74 6>, <83 4>, <125 2>, <128 2>, <154 7>;
> +
> + kybd_default: kybd-default-state {
> + disable {
> + pins = "gpio102";
> + function = "gpio";
> + output-low;
> + };
> +
> + int-n {
> + pins = "gpio104";
> + function = "gpio";
> + bias-disable;
> + };
> +
> + reset {
> + pins = "gpio105";
> + function = "gpio";
> + bias-disable;
> + };
> + };
> +
> + qup0_i2c4_default: qup0-i2c4-default-state {
> + pins = "gpio171", "gpio172";
> + function = "qup4";
> +
> + bias-disable;
> + drive-strength = <16>;
> + };
> +
> + qup2_i2c5_default: qup2-i2c5-default-state {
> + pins = "gpio81", "gpio82";
> + function = "qup21";
> +
> + bias-disable;
> + drive-strength = <16>;
> + };
> +
> + tpad_default: tpad-default-state {
> + int-n {
If you aren't gonna add more pins to this touchpad block, I think you could drop this extra level.


> + pins = "gpio182";
> + function = "gpio";
> + bias-disable;
> + };
> + };
> +
> + ts0_default: ts0-default-state {
> + int-n {
> + pins = "gpio175";
> + function = "gpio";
> + bias-pull-up;
> + };
> +
> + reset-n {
> + pins = "gpio99";
> + function = "gpio";
> + output-high;
> + drive-strength = <16>;
> + };
> + };
> +};
> diff --git a/arch/arm64/boot/dts/qcom/sc8280xp-pmics.dtsi b/arch/arm64/boot/dts/qcom/sc8280xp-pmics.dtsi
> new file mode 100644
> index 000000000000..36ed7d808ab8
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/sc8280xp-pmics.dtsi
Is it the only configuration supported by Qualcomm, or only a reference one?

Konrad


> @@ -0,0 +1,108 @@
> +// SPDX-License-Identifier: BSD-3-Clause
> +/*
> + * Copyright (c) 2022, Linaro Limited
> + */
> +
> +#include <dt-bindings/interrupt-controller/irq.h>
> +#include <dt-bindings/spmi/spmi.h>
> +
> +&spmi_bus {
> + pmk8280: pmic@0 {
> + compatible = "qcom,pmk8350", "qcom,spmi-pmic";
> + reg = <0x0 SPMI_USID>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + pmk8280_pon: pon@1300 {
> + compatible = "qcom,pm8998-pon";
> + reg = <0x1300>;
> +
> + pmk8280_pon_pwrkey: pwrkey {
> + compatible = "qcom,pmk8350-pwrkey";
> + interrupts = <0x0 0x13 0x7 IRQ_TYPE_EDGE_BOTH>;
> + linux,code = <KEY_POWER>;
> + status = "disabled";
> + };
> + };
> + };
> +
> + pmc8280_1: pmic@1 {
> + compatible = "qcom,pm8350", "qcom,spmi-pmic";
> + reg = <0x1 SPMI_USID>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + pmc8280_1_gpios: gpio@8800 {
> + compatible = "qcom,pm8350-gpio", "qcom,spmi-gpio";
> + reg = <0x8800>;
> + gpio-controller;
> + gpio-ranges = <&pmc8280_1_gpios 0 0 10>;
> + #gpio-cells = <2>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> + };
> +
> + pmc8280c: pmic@2 {
> + compatible = "qcom,pm8350c", "qcom,spmi-pmic";
> + reg = <0x2 SPMI_USID>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + pmc8280c_gpios: gpio@8800 {
> + compatible = "qcom,pm8350c-gpio", "qcom,spmi-gpio";
> + reg = <0x8800>;
> + gpio-controller;
> + gpio-ranges = <&pmc8280c_gpios 0 0 9>;
> + #gpio-cells = <2>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> +
> + pmc8280c_lpg: lpg@e800 {
> + compatible = "qcom,pm8350c-pwm";
> + reg = <0xe800>;
> +
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + #pwm-cells = <2>;
> +
> + status = "disabled";
> + };
> + };
> +
> + pmc8280_2: pmic@3 {
> + compatible = "qcom,pm8350", "qcom,spmi-pmic";
> + reg = <0x3 SPMI_USID>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + pmc8280_2_gpios: gpio@8800 {
> + compatible = "qcom,pm8350-gpio", "qcom,spmi-gpio";
> + reg = <0x8800>;
> + gpio-controller;
> + gpio-ranges = <&pmc8280_2_gpios 0 0 10>;
> + #gpio-cells = <2>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> + };
> +
> + pmr735a: pmic@4 {
> + compatible = "qcom,pmr735a", "qcom,spmi-pmic";
> + reg = <0x4 SPMI_USID>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + pmr735a_gpios: gpio@8800 {
> + compatible = "qcom,pmr735a-gpio", "qcom,spmi-gpio";
> + reg = <0x8800>;
> + gpio-controller;
> + gpio-ranges = <&pmr735a_gpios 0 0 4>;
> + #gpio-cells = <2>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> + };
> +};
>

\
 
 \ /
  Last update: 2022-06-22 14:34    [W:0.229 / U:0.080 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site