lkml.org 
[lkml]   [2022]   [Jun]   [19]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH V4] dt-bindings: dma: fsl-edma: Convert to DT schema
Date
From: Peng Fan <peng.fan@nxp.com>

Convert the eDMA controller binding to DT schema.

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
---

V4:
Add R-b tag from DT maintainer
Rebase with linux-next/master

.../devicetree/bindings/dma/fsl,edma.yaml | 155 ++++++++++++++++++
.../devicetree/bindings/dma/fsl-edma.txt | 111 -------------
2 files changed, 155 insertions(+), 111 deletions(-)
create mode 100644 Documentation/devicetree/bindings/dma/fsl,edma.yaml
delete mode 100644 Documentation/devicetree/bindings/dma/fsl-edma.txt

diff --git a/Documentation/devicetree/bindings/dma/fsl,edma.yaml b/Documentation/devicetree/bindings/dma/fsl,edma.yaml
new file mode 100644
index 000000000000..050e6cd57727
--- /dev/null
+++ b/Documentation/devicetree/bindings/dma/fsl,edma.yaml
@@ -0,0 +1,155 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/dma/fsl,edma.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Freescale enhanced Direct Memory Access(eDMA) Controller
+
+description: |
+ The eDMA channels have multiplex capability by programmable
+ memory-mapped registers. channels are split into two groups, called
+ DMAMUX0 and DMAMUX1, specific DMA request source can only be multiplexed
+ by any channel of certain group, DMAMUX0 or DMAMUX1, but not both.
+
+maintainers:
+ - Peng Fan <peng.fan@nxp.com>
+
+properties:
+ compatible:
+ oneOf:
+ - enum:
+ - fsl,vf610-edma
+ - fsl,imx7ulp-edma
+ - items:
+ - const: fsl,ls1028a-edma
+ - const: fsl,vf610-edma
+
+ reg:
+ minItems: 2
+ maxItems: 3
+
+ interrupts:
+ minItems: 2
+ maxItems: 17
+
+ interrupt-names:
+ minItems: 2
+ maxItems: 17
+
+ "#dma-cells":
+ const: 2
+
+ dma-channels:
+ const: 32
+
+ clocks:
+ maxItems: 2
+
+ clock-names:
+ maxItems: 2
+
+ big-endian:
+ description: |
+ If present registers and hardware scatter/gather descriptors of the
+ eDMA are implemented in big endian mode, otherwise in little mode.
+ type: boolean
+
+required:
+ - "#dma-cells"
+ - compatible
+ - reg
+ - interrupts
+ - clocks
+ - dma-channels
+
+allOf:
+ - $ref: "dma-controller.yaml#"
+ - if:
+ properties:
+ compatible:
+ contains:
+ const: fsl,vf610-edma
+ then:
+ properties:
+ clock-names:
+ items:
+ - const: dmamux0
+ - const: dmamux1
+ interrupts:
+ maxItems: 2
+ interrupt-names:
+ items:
+ - const: edma-tx
+ - const: edma-err
+ reg:
+ maxItems: 3
+
+ - if:
+ properties:
+ compatible:
+ contains:
+ const: fsl,imx7ulp-edma
+ then:
+ properties:
+ clock-names:
+ items:
+ - const: dma
+ - const: dmamux0
+ interrupts:
+ maxItems: 17
+ reg:
+ maxItems: 2
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/clock/vf610-clock.h>
+
+ edma0: dma-controller@40018000 {
+ #dma-cells = <2>;
+ compatible = "fsl,vf610-edma";
+ reg = <0x40018000 0x2000>,
+ <0x40024000 0x1000>,
+ <0x40025000 0x1000>;
+ interrupts = <0 8 IRQ_TYPE_LEVEL_HIGH>,
+ <0 9 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "edma-tx", "edma-err";
+ dma-channels = <32>;
+ clock-names = "dmamux0", "dmamux1";
+ clocks = <&clks VF610_CLK_DMAMUX0>, <&clks VF610_CLK_DMAMUX1>;
+ };
+
+ - |
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/clock/imx7ulp-clock.h>
+
+ edma1: dma-controller@40080000 {
+ #dma-cells = <2>;
+ compatible = "fsl,imx7ulp-edma";
+ reg = <0x40080000 0x2000>,
+ <0x40210000 0x1000>;
+ dma-channels = <32>;
+ interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
+ /* last is eDMA2-ERR interrupt */
+ <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+ clock-names = "dma", "dmamux0";
+ clocks = <&pcc2 IMX7ULP_CLK_DMA1>, <&pcc2 IMX7ULP_CLK_DMA_MUX1>;
+ };
diff --git a/Documentation/devicetree/bindings/dma/fsl-edma.txt b/Documentation/devicetree/bindings/dma/fsl-edma.txt
deleted file mode 100644
index ee1754739b4b..000000000000
--- a/Documentation/devicetree/bindings/dma/fsl-edma.txt
+++ /dev/null
@@ -1,111 +0,0 @@
-* Freescale enhanced Direct Memory Access(eDMA) Controller
-
- The eDMA channels have multiplex capability by programmble memory-mapped
-registers. channels are split into two groups, called DMAMUX0 and DMAMUX1,
-specific DMA request source can only be multiplexed by any channel of certain
-group, DMAMUX0 or DMAMUX1, but not both.
-
-* eDMA Controller
-Required properties:
-- compatible :
- - "fsl,vf610-edma" for eDMA used similar to that on Vybrid vf610 SoC
- - "fsl,imx7ulp-edma" for eDMA2 used similar to that on i.mx7ulp
- - "fsl,ls1028a-edma" followed by "fsl,vf610-edma" for eDMA used on the
- LS1028A SoC.
-- reg : Specifies base physical address(s) and size of the eDMA registers.
- The 1st region is eDMA control register's address and size.
- The 2nd and the 3rd regions are programmable channel multiplexing
- control register's address and size.
-- interrupts : A list of interrupt-specifiers, one for each entry in
- interrupt-names on vf610 similar SoC. But for i.mx7ulp per channel
- per transmission interrupt, total 16 channel interrupt and 1
- error interrupt(located in the last), no interrupt-names list on
- i.mx7ulp for clean on dts.
-- #dma-cells : Must be <2>.
- The 1st cell specifies the DMAMUX(0 for DMAMUX0 and 1 for DMAMUX1).
- Specific request source can only be multiplexed by specific channels
- group called DMAMUX.
- The 2nd cell specifies the request source(slot) ID.
- See the SoC's reference manual for all the supported request sources.
-- dma-channels : Number of channels supported by the controller
-- clock-names : A list of channel group clock names. Should contain:
- "dmamux0" - clock name of mux0 group
- "dmamux1" - clock name of mux1 group
- Note: No dmamux0 on i.mx7ulp, but another 'dma' clk added on i.mx7ulp.
-- clocks : A list of phandle and clock-specifier pairs, one for each entry in
- clock-names.
-
-Optional properties:
-- big-endian: If present registers and hardware scatter/gather descriptors
- of the eDMA are implemented in big endian mode, otherwise in little
- mode.
-- interrupt-names : Should contain the below on vf610 similar SoC but not used
- on i.mx7ulp similar SoC:
- "edma-tx" - the transmission interrupt
- "edma-err" - the error interrupt
-
-
-Examples:
-
-edma0: dma-controller@40018000 {
- #dma-cells = <2>;
- compatible = "fsl,vf610-edma";
- reg = <0x40018000 0x2000>,
- <0x40024000 0x1000>,
- <0x40025000 0x1000>;
- interrupts = <0 8 IRQ_TYPE_LEVEL_HIGH>,
- <0 9 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-names = "edma-tx", "edma-err";
- dma-channels = <32>;
- clock-names = "dmamux0", "dmamux1";
- clocks = <&clks VF610_CLK_DMAMUX0>,
- <&clks VF610_CLK_DMAMUX1>;
-}; /* vf610 */
-
-edma1: dma-controller@40080000 {
- #dma-cells = <2>;
- compatible = "fsl,imx7ulp-edma";
- reg = <0x40080000 0x2000>,
- <0x40210000 0x1000>;
- dma-channels = <32>;
- interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
- /* last is eDMA2-ERR interrupt */
- <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
- clock-names = "dma", "dmamux0";
- clocks = <&pcc2 IMX7ULP_CLK_DMA1>,
- <&pcc2 IMX7ULP_CLK_DMA_MUX1>;
-}; /* i.mx7ulp */
-
-* DMA clients
-DMA client drivers that uses the DMA function must use the format described
-in the dma.txt file, using a two-cell specifier for each channel: the 1st
-specifies the channel group(DMAMUX) in which this request can be multiplexed,
-and the 2nd specifies the request source.
-
-Examples:
-
-sai2: sai@40031000 {
- compatible = "fsl,vf610-sai";
- reg = <0x40031000 0x1000>;
- interrupts = <0 86 IRQ_TYPE_LEVEL_HIGH>;
- clock-names = "sai";
- clocks = <&clks VF610_CLK_SAI2>;
- dma-names = "tx", "rx";
- dmas = <&edma0 0 21>,
- <&edma0 0 20>;
-};
--
2.25.1
\
 
 \ /
  Last update: 2022-06-20 03:59    [W:0.049 / U:1.208 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site