lkml.org 
[lkml]   [2022]   [Jun]   [16]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 2/7] dt-bindings: phy: add binding document for Allwinner F1C100s USB PHY
On Wed, Jun 08, 2022 at 10:52:52PM +0800, Icenowy Zheng wrote:
> 在 2022-06-08星期三的 08:49 -0600,Rob Herring写道:
> > On Wed, Jun 08, 2022 at 03:04:47PM +0800, Icenowy Zheng wrote:
> > > Allwinner F1C100s has the most simple USB PHY among all Allwinner
> > > SoCs,
> > > because it has only one OTG USB controller, no host-only OHCI/EHCI
> > > controllers.
> > >
> > > Add a binding document for it.
> > >
> > > Signed-off-by: Icenowy Zheng <uwu@icenowy.me>
> > > ---
> > >  .../phy/allwinner,suniv-f1c100s-usb-phy.yaml  | 83
> > > +++++++++++++++++++
> > >  1 file changed, 83 insertions(+)
> > >  create mode 100644
> > > Documentation/devicetree/bindings/phy/allwinner,suniv-f1c100s-usb-
> > > phy.yaml
> > >
> > > diff --git a/Documentation/devicetree/bindings/phy/allwinner,suniv-
> > > f1c100s-usb-phy.yaml
> > > b/Documentation/devicetree/bindings/phy/allwinner,suniv-f1c100s-
> > > usb-phy.yaml
> > > new file mode 100644
> > > index 000000000000..180fa8840bf7
> > > --- /dev/null
> > > +++ b/Documentation/devicetree/bindings/phy/allwinner,suniv-
> > > f1c100s-usb-phy.yaml
> > > @@ -0,0 +1,83 @@
> > > +# SPDX-License-Identifier: GPL-2.0
> >
> > Dual license please.
>
> I am based on another Allwinner USB PHY binding file in the same
> directory, and that file is single licensed. I created a new file
> because each variant of the PHY has a single file now.

Okay, describing the source and the differences in the commit message
would be helpful.

>
> >
> > > +%YAML 1.2
> > > +---
> > > +$id:
> > > http://devicetree.org/schemas/phy/allwinner,suniv-f1c100s-usb-phy.yaml#
> > > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > > +
> > > +title: Allwinner F1C100s USB PHY Device Tree Bindings
> > > +
> > > +maintainers:
> > > +  - Chen-Yu Tsai <wens@csie.org>
> > > +  - Maxime Ripard <mripard@kernel.org>
> > > +
> > > +properties:
> > > +  "#phy-cells":
> > > +    const: 1
> > > +
> > > +  compatible:
> > > +    const: allwinner,suniv-f1c100s-usb-phy
> > > +
> > > +  reg:
> > > +    maxItems: 1
> > > +    description: PHY Control registers
> > > +
> > > +  reg-names:
> > > +    const: phy_ctrl
> > > +
> > > +  clocks:
> > > +    maxItems: 1
> > > +    description: USB OTG PHY bus clock
> > > +
> > > +  clock-names:
> > > +    const: usb0_phy
> >
> > *-names is not needed with only one entry. Plus, just using the
> > module
> > name is not a great choice.
>
> However the driver expects it...
>
> Should I patch the driver to use no name on F1C100s?
>
> >
> > > +
> > > +  resets:
> > > +    maxItems: 1
> > > +    description: USB OTG reset
> > > +
> > > +  reset-names:
> > > +    const: usb0_reset
> >
> > Same here.
> >
> > > +  usb0_id_det-gpios:
> > > +    maxItems: 1
> > > +    description: GPIO to the USB OTG ID pin
> > > +
> > > +  usb0_vbus_det-gpios:
> > > +    maxItems: 1
> > > +    description: GPIO to the USB OTG VBUS detect pin
> > > +
> > > +  usb0_vbus_power-supply:
> > > +    description: Power supply to detect the USB OTG VBUS
> > > +
> > > +  usb0_vbus-supply:
> > > +    description: Regulator controlling USB OTG VBUS
> >
> > Why the 'usb0_' prefix?
> >
> > Are these GPIOs and Vbus supply connected to the phy? If not, these
> > all
> > belong in a connector node (as that is where they are connected to in
> > h/w).
>
> Well these are historical things of phy-sun4i-usb driver too.

Okay, there should perhaps be a common schema so this sharing is clear.
Though longer term there should be a move to the common way of handling
these for new platforms.

So I guess in summary:

Reviewed-by: Rob Herring <robh@kernel.org>

\
 
 \ /
  Last update: 2022-06-16 18:01    [W:0.040 / U:0.784 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site