lkml.org 
[lkml]   [2022]   [Jun]   [14]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
SubjectRe: [PATCH v4 12/23] ata: libahci: Extend port-cmd flags set with port capabilities
From
On 6/10/22 17:17, Serge Semin wrote:
> Currently not all of the Port-specific capabilities listed in the

s/listed/are listed

> PORT_CMD-enumeration. Let's extend that set with the Cold Presence
> Detection and Mechanical Presence Switch attached to the Port flags [1] so
> to closeup the set of the platform-specific port-capabilities flags. Note
> these flags are supposed to be set by the platform firmware if there is
> one. Alternatively as we are about to do they can be set by means of the
> OF properties.
>
> While at it replace PORT_IRQ_DEV_ILCK with PORT_IRQ_DMPS and fix the
> comment there. In accordance with [2] that IRQ flag is supposed to
> indicate the state of the signal coming from the Mechanical Presence
> Switch.
>
> [1] Serial ATA AHCI 1.3.1 Specification, p.27
> [2] Serial ATA AHCI 1.3.1 Specification, p.24, p.88
>
> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
> Reviewed-by: Hannes Reinecke <hare@suse.de>
>
> ---
>
> Changelog v4:
> - Fix the DMPS macros name in the patch log. (@Sergei Shtylyov)
> ---
> drivers/ata/ahci.h | 7 ++++++-
> 1 file changed, 6 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/ata/ahci.h b/drivers/ata/ahci.h
> index 7d834deefeb9..f501531bd1b3 100644
> --- a/drivers/ata/ahci.h
> +++ b/drivers/ata/ahci.h
> @@ -138,7 +138,7 @@ enum {
> PORT_IRQ_BAD_PMP = (1 << 23), /* incorrect port multiplier */
>
> PORT_IRQ_PHYRDY = (1 << 22), /* PhyRdy changed */
> - PORT_IRQ_DEV_ILCK = (1 << 7), /* device interlock */
> + PORT_IRQ_DMPS = (1 << 7), /* mechanical presence status */
> PORT_IRQ_CONNECT = (1 << 6), /* port connect change status */
> PORT_IRQ_SG_DONE = (1 << 5), /* descriptor processed */
> PORT_IRQ_UNK_FIS = (1 << 4), /* unknown FIS rx'd */
> @@ -166,6 +166,8 @@ enum {
> PORT_CMD_ATAPI = (1 << 24), /* Device is ATAPI */
> PORT_CMD_FBSCP = (1 << 22), /* FBS Capable Port */
> PORT_CMD_ESP = (1 << 21), /* External Sata Port */
> + PORT_CMD_CPD = (1 << 20), /* Cold Presence Detection */
> + PORT_CMD_MPSP = (1 << 19), /* Mechanical Presence Switch */
> PORT_CMD_HPCP = (1 << 18), /* HotPlug Capable Port */
> PORT_CMD_PMP = (1 << 17), /* PMP attached */
> PORT_CMD_LIST_ON = (1 << 15), /* cmd list DMA engine running */
> @@ -181,6 +183,9 @@ enum {
> PORT_CMD_ICC_PARTIAL = (0x2 << 28), /* Put i/f in partial state */
> PORT_CMD_ICC_SLUMBER = (0x6 << 28), /* Put i/f in slumber state */
>
> + PORT_CMD_CAP = PORT_CMD_HPCP | PORT_CMD_MPSP |
> + PORT_CMD_CPD | PORT_CMD_ESP | PORT_CMD_FBSCP,

What is this one for ? A comment above it would be nice.

> +
> /* PORT_FBS bits */
> PORT_FBS_DWE_OFFSET = 16, /* FBS device with error offset */
> PORT_FBS_ADO_OFFSET = 12, /* FBS active dev optimization offset */


--
Damien Le Moal
Western Digital Research

\
 
 \ /
  Last update: 2022-06-14 10:34    [W:0.293 / U:0.364 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site