lkml.org 
[lkml]   [2022]   [Jun]   [14]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v20 2/5] usb: dwc3: core: Host wake up support from system suspend
On Mon, Jun 13, 2022 at 11:08:32AM -0700, Matthias Kaehlcke wrote:
> On Mon, Jun 06, 2022 at 01:45:51PM -0700, Matthias Kaehlcke wrote:
> > On Thu, Jun 02, 2022 at 12:35:42PM -0700, Matthias Kaehlcke wrote:
> > > Hi Krishna,
> > >
> > > with this version I see xHCI errors on my SC7180 based system, like
> > > these:
> > >
> > > [ 65.352605] xhci-hcd xhci-hcd.13.auto: xHC error in resume, USBSTS 0x401, Reinit
> > >
> > > [ 101.307155] xhci-hcd xhci-hcd.13.auto: WARN: xHC CMD_RUN timeout
> > >
> > > After resume a downstream hub isn't enumerated again.
> > >
> > > So far I didn't see those with v13, but I aso saw the first error with
> > > v16.
> >
> > It also happens with v13, but only when a wakeup capable vUSB <= 2
> > device is plugged in. Initially I used a wakeup capable USB3 to
> > Ethernet adapter to trigger the wakeup case, however older versions
> > of this series that use usb_wakeup_enabled_descendants() to check
> > for wakeup capable devices didn't actually check for vUSB > 2
> > devices.
> >
> > So the case were the controller/PHYs is powered down works, but
> > the controller is unhappy when the runtime PM path is used during
> > system suspend.
>
> The issue isn't seen on all systems using dwc3-qcom and the problem starts
> during probe(). The expected probe sequence is something like this:
>
> dwc3_qcom_probe
> dwc3_qcom_of_register_core
> dwc3_probe
>
> if (device_can_wakeup(&qcom->dwc3->dev))
> ...
>
> The important part is that device_can_wakeup() is called after dwc3_probe()
> has completed. That's what I see on a QC SC7280 system, where wakeup is
> generally working with these patches.
>
> However on a QC SC7180 system dwc3_probe() is deferred and only executed after
> dwc3_qcom_probe(). As a result the device_can_wakeup() call returns false.
> With that the controller/driver ends up in an unhappy state after system
> suspend.
>
> Probing is deferred on SC7180 because device_links_check_suppliers() finds
> that '88e3000.phy' isn't ready yet.

It seems device links could be used to make sure the dwc3 core is present:

Another example for an inconsistent state would be a device link that
represents a driver presence dependency, yet is added from the consumer’s
->probe callback while the supplier hasn’t probed yet: Had the driver core
known about the device link earlier, it wouldn’t have probed the consumer
in the first place. The onus is thus on the consumer to check presence of
the supplier after adding the link, and defer probing on non-presence.

https://www.kernel.org/doc/html/v5.18/driver-api/device_link.html#usage


You could add something like this to dwc3_qcom_of_register_core():


device_link_add(dev, &qcom->dwc3->dev,
DL_FLAG_AUTOREMOVE_CONSUMER | DL_FLAG_AUTOPROBE_CONSUMER);

if (qcom->dwc3->dev.links.status != DL_DEV_DRIVER_BOUND)
ret = -EPROBE_DEFER;


From the doc it isn't clear how the consumer is supposed to check presence
of the supplier, the above check of the link status is also used in
drivers/cpufreq/mediatek-cpufreq.c , but not elsewhere outside of the
driver framework.

\
 
 \ /
  Last update: 2022-06-14 19:54    [W:0.262 / U:0.208 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site