lkml.org 
[lkml]   [2022]   [May]   [5]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v9 8/8] PCI: imx6: Add compliance tests mode support
Date
Refer to the Chapter 3.2 System Board Signal Quality of PCI Express
Architecture PHY Test Specification Revision 2.0.

Signal quality tests (for example: jitter, differential eye opening and
so on) can be executed with devices in the polling.compliance state.

To let the device support polling.compliance state, the clocks and powers
shouldn't be turned off when the probe of device driver fails.

Based on CLB (Compliance Load Board) Test Fixture and so on test
equipments, the PHY link would be down during the compliance tests.
Refer to this scenario, add the i.MX PCIe compliance tests mode enable
support, and keep the clocks and powers on, and finish the driver probe
without error return.

Use the "pci_imx6.compliance=1" in kernel command line to enable the
compliance tests mode.

Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
---
drivers/pci/controller/dwc/pci-imx6.c | 39 ++++++++++++++++++---------
1 file changed, 27 insertions(+), 12 deletions(-)

diff --git a/drivers/pci/controller/dwc/pci-imx6.c b/drivers/pci/controller/dwc/pci-imx6.c
index f0ffd9011975..f78b59822626 100644
--- a/drivers/pci/controller/dwc/pci-imx6.c
+++ b/drivers/pci/controller/dwc/pci-imx6.c
@@ -146,6 +146,10 @@ struct imx6_pcie {
#define PHY_RX_OVRD_IN_LO_RX_DATA_EN BIT(5)
#define PHY_RX_OVRD_IN_LO_RX_PLL_EN BIT(3)

+static bool imx6_pcie_cmp_mode;
+module_param_named(compliance, imx6_pcie_cmp_mode, bool, 0644);
+MODULE_PARM_DESC(compliance, "i.MX PCIe compliance test mode (1=compliance test mode enabled)");
+
static int pcie_phy_poll_ack(struct imx6_pcie *imx6_pcie, bool exp_val)
{
struct dw_pcie *pci = imx6_pcie->pci;
@@ -826,10 +830,12 @@ static int imx6_pcie_start_link(struct dw_pcie *pci)
* started in Gen2 mode, there is a possibility the devices on the
* bus will not be detected at all. This happens with PCIe switches.
*/
- tmp = dw_pcie_readl_dbi(pci, offset + PCI_EXP_LNKCAP);
- tmp &= ~PCI_EXP_LNKCAP_SLS;
- tmp |= PCI_EXP_LNKCAP_SLS_2_5GB;
- dw_pcie_writel_dbi(pci, offset + PCI_EXP_LNKCAP, tmp);
+ if (!imx6_pcie_cmp_mode) {
+ tmp = dw_pcie_readl_dbi(pci, offset + PCI_EXP_LNKCAP);
+ tmp &= ~PCI_EXP_LNKCAP_SLS;
+ tmp |= PCI_EXP_LNKCAP_SLS_2_5GB;
+ dw_pcie_writel_dbi(pci, offset + PCI_EXP_LNKCAP, tmp);
+ }

/* Start LTSSM. */
imx6_pcie_ltssm_enable(dev);
@@ -887,14 +893,16 @@ static int imx6_pcie_start_link(struct dw_pcie *pci)
dev_dbg(dev, "PHY DEBUG_R0=0x%08x DEBUG_R1=0x%08x\n",
dw_pcie_readl_dbi(pci, PCIE_PORT_DEBUG0),
dw_pcie_readl_dbi(pci, PCIE_PORT_DEBUG1));
- imx6_pcie_reset_phy(imx6_pcie);
- imx6_pcie_clk_disable(imx6_pcie);
- if (imx6_pcie->phy != NULL) {
- phy_power_off(imx6_pcie->phy);
- phy_exit(imx6_pcie->phy);
+ if (!imx6_pcie_cmp_mode) {
+ imx6_pcie_reset_phy(imx6_pcie);
+ imx6_pcie_clk_disable(imx6_pcie);
+ if (imx6_pcie->phy != NULL) {
+ phy_power_off(imx6_pcie->phy);
+ phy_exit(imx6_pcie->phy);
+ }
+ if (imx6_pcie->vpcie)
+ regulator_disable(imx6_pcie->vpcie);
}
- if (imx6_pcie->vpcie)
- regulator_disable(imx6_pcie->vpcie);
return ret;
}

@@ -1289,8 +1297,15 @@ static int imx6_pcie_probe(struct platform_device *pdev)
return ret;

ret = dw_pcie_host_init(&pci->pp);
- if (ret < 0)
+ if (ret < 0) {
+ if (imx6_pcie_cmp_mode) {
+ dev_info(dev, "driver loaded with compliance test mode enabled\n");
+ ret = 0;
+ } else {
+ dev_err(dev, "unable to add PCIe port\n");
+ }
return ret;
+ }

if (pci_msi_enabled()) {
u8 offset = dw_pcie_find_capability(pci, PCI_CAP_ID_MSI);
--
2.25.1
\
 
 \ /
  Last update: 2022-05-06 04:01    [W:0.196 / U:0.140 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site