lkml.org 
[lkml]   [2022]   [May]   [31]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 1/4] media: i2c: ov5695: use regulator_bulk_enable/regulator_bulk disable instead of for loop
Hi Tommaso,

On Thu, May 19, 2022 at 09:51:14AM +0200, Tommaso Merciai wrote:
> Enable regulator using regulator_bulk_enable/regulatore_bulk_disable
> function in __ov5695_power_on/__ov5695_power_off function instead of for loop.
> This reduce code size and make things more clear
>
> Signed-off-by: Tommaso Merciai <tommaso.merciai@amarulasolutions.com>
> Co-Developed-by: Michael Trimarchi <michael@amarulasolutions.com>
> ---
> drivers/media/i2c/ov5695.c | 25 +++++++------------------
> 1 file changed, 7 insertions(+), 18 deletions(-)
>
> diff --git a/drivers/media/i2c/ov5695.c b/drivers/media/i2c/ov5695.c
> index 439385938a51..880b586e55fe 100644
> --- a/drivers/media/i2c/ov5695.c
> +++ b/drivers/media/i2c/ov5695.c
> @@ -972,7 +972,7 @@ static int ov5695_s_stream(struct v4l2_subdev *sd, int on)
>
> static int __ov5695_power_on(struct ov5695 *ov5695)
> {
> - int i, ret;
> + int ret;
> struct device *dev = &ov5695->client->dev;
>
> ret = clk_prepare_enable(ov5695->xvclk);
> @@ -987,13 +987,10 @@ static int __ov5695_power_on(struct ov5695 *ov5695)
> * The hardware requires the regulators to be powered on in order,
> * so enable them one by one.
> */

The comment says that the hardware requires regulators to be enabled
in precise order

> - for (i = 0; i < OV5695_NUM_SUPPLIES; i++) {
> - ret = regulator_enable(ov5695->supplies[i].consumer);
> - if (ret) {
> - dev_err(dev, "Failed to enable %s: %d\n",
> - ov5695->supplies[i].supply, ret);
> - goto disable_reg_clk;
> - }
> + ret = regulator_bulk_enable(ARRAY_SIZE(ov5695->supplies), ov5695->supplies);

bulk_enable() uses the async API (async_schedule_domain() in
particular) which by the name makes me think such ordering guarantee
cannot be respected.

However most sensors require some kind of ordering when enabling
regulators, and most of the use the bulk API anyhow. The fact this
driver uses the bulk API to get an release the regulators but not for
enabling them and the above comment, makes me think it has been done
on purpose ? Could you check with the driver author maybe ?

> + if (ret) {
> + dev_err(dev, "Failed to enable regulators %d\n", ret);
> + goto disable_reg_clk;
> }
>
> gpiod_set_value_cansleep(ov5695->reset_gpio, 0);
> @@ -1003,8 +1000,7 @@ static int __ov5695_power_on(struct ov5695 *ov5695)
> return 0;
>
> disable_reg_clk:
> - for (--i; i >= 0; i--)
> - regulator_disable(ov5695->supplies[i].consumer);
> + regulator_bulk_disable(ARRAY_SIZE(ov5695->supplies), ov5695->supplies);

FYI the bulk API does this for you if enabling any of the regulators fails.
Hence this should not be necessary.

Thanks
j

> clk_disable_unprepare(ov5695->xvclk);
>
> return ret;
> @@ -1012,8 +1008,6 @@ static int __ov5695_power_on(struct ov5695 *ov5695)
>
> static void __ov5695_power_off(struct ov5695 *ov5695)
> {
> - struct device *dev = &ov5695->client->dev;
> - int i, ret;
>
> clk_disable_unprepare(ov5695->xvclk);
> gpiod_set_value_cansleep(ov5695->reset_gpio, 1);
> @@ -1022,12 +1016,7 @@ static void __ov5695_power_off(struct ov5695 *ov5695)
> * The hardware requires the regulators to be powered off in order,
> * so disable them one by one.
> */
> - for (i = OV5695_NUM_SUPPLIES - 1; i >= 0; i--) {
> - ret = regulator_disable(ov5695->supplies[i].consumer);
> - if (ret)
> - dev_err(dev, "Failed to disable %s: %d\n",
> - ov5695->supplies[i].supply, ret);
> - }
> + regulator_bulk_disable(ARRAY_SIZE(ov5695->supplies), ov5695->supplies);
> }
>
> static int __maybe_unused ov5695_runtime_resume(struct device *dev)
> --
> 2.25.1
>

\
 
 \ /
  Last update: 2022-05-31 15:14    [W:0.089 / U:0.028 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site