lkml.org 
[lkml]   [2022]   [May]   [30]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v13 2/3] fpga: microchip-spi: add Microchip MPF FPGA manager
On Mon, May 30, 2022 at 02:26:18PM +0000, Conor.Dooley@microchip.com wrote:
> On 30/05/2022 13:07, Ivan Bornyakov wrote:
> > EXTERNAL EMAIL: Do not click links or open attachments unless you know the content is safe
> >
> > On Mon, May 30, 2022 at 11:22:26AM +0000, Conor.Dooley@microchip.com wrote:
> >> On 26/05/2022 19:13, Ivan Bornyakov wrote:
> >>> +static int mpf_read_status(struct spi_device *spi)
> >>> +{
> >>> + u8 status = 0, status_command = MPF_SPI_READ_STATUS;
> >>> + /*
> >>> + * Two identical SPI transfers are used for status reading.
> >>> + * The reason is that the first one can be inadequate.
> >>> + * We ignore it completely and use the second one.
> >>> + */
> >>> + struct spi_transfer xfers[] = {
> >>> + [0 ... 1] = {
> >>> + .tx_buf = &status_command,
> >>> + .rx_buf = &status,
> >>> + .len = 1,
> >>> + .cs_change = 1,
> >>> + }
> >>> + };
> >>
> >> Hmm, I don't think that this is correct, or at least it is not
> >> correct from the polarfire /soc/ perspective. I was told that
> >> there was nothing different other than the envm between the
> >> programming for both devices - but this is another situation
> >> where I start to question that.
> >>
> >> When I run this code, ISC enable /never/ passes - failing due
> >> to timing out. I see something like this picture here:
> >> https://i.imgur.com/EKhd1S3.png
> >> You can see the 0x0B ISC enable coming through & then a status
> >> check after it.
> >>
> >> With the current code, the value of the "status" variable will
> >> be 0x0, given you are overwriting the first MISO value with the
> >> second. According to the hw guys, the spi hw status *should*
> >> only be returned on MISO in the first byte after SS goes low.
> >>
> >> If this is not the case for a non -soc part, which, as I said
> >> before, I don't have a board with the SPI programmer exposed
> >> for & I have been told is not the case then my comments can
> >> just be ignored entirely & I'll have some head scratching to
> >> do...
> >>
> >> Thanks,
> >> Conor.
> >>
> >
> > If I understood correctly, SS doesn't alter between two status reading
> > transactions despite .cs_change = 1. May be adding some .cs_change_delay
> > to spi_transfer struct can help with that?
>
> D-oh - bug in the spi controller driver :)

So, no additional delay is needed?

> LGTM now, successfully programmed my PolarFire SoC with v12.
> I'd almost suggest adding a compatible for it too - but since
> the envm programming doesn't work I don't think that would be
> correct.
>
> Tested-by: Conor Dooley <conor.dooley@microchip.com>
>
> With a small comment about why it's using spi_sync_transfer():
> Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
>

Thanks for your assistance, Conor!

> >
> >>> + int ret = spi_sync_transfer(spi, xfers, 2);
> >>> +
> >>> + if ((status & MPF_STATUS_SPI_VIOLATION) ||
> >>> + (status & MPF_STATUS_SPI_ERROR))
> >>> + ret = -EIO;
> >>> +
> >>> + return ret ? : status;
> >>> +}
> >
>

\
 
 \ /
  Last update: 2022-05-30 17:43    [W:0.101 / U:0.820 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site