lkml.org 
[lkml]   [2022]   [May]   [25]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 08/40] hwmon: (lm90) Improve PEC support
Date
PEC (packet error checking) support for ADM1032 is currently only enabled
if the chip was auto-detected, but not if a chip is instantiated
explicitly. Always enable PEC support by introducing a chip feature flag
indicating partial PEC support. Also, for consistency, disable PEC support
by default to match existing functionality if the chip was not auto-
detected.

At the same time, introduce generic support for PEC with a separate feature
flag. This will be used when support for chips with full PEC functionality
is added.

Signed-off-by: Guenter Roeck <linux@roeck-us.net>
---
Documentation/hwmon/lm90.rst | 6 ++--
drivers/hwmon/lm90.c | 56 +++++++++++++++++++-----------------
2 files changed, 32 insertions(+), 30 deletions(-)

diff --git a/Documentation/hwmon/lm90.rst b/Documentation/hwmon/lm90.rst
index 05391fb4042d..f107d4a159fa 100644
--- a/Documentation/hwmon/lm90.rst
+++ b/Documentation/hwmon/lm90.rst
@@ -423,6 +423,6 @@ two transactions will typically mean twice as much delay waiting for
transaction completion, effectively doubling the register cache refresh time.
I guess reliability comes at a price, but it's quite expensive this time.

-So, as not everyone might enjoy the slowdown, PEC can be disabled through
-sysfs. Just write 0 to the "pec" file and PEC will be disabled. Write 1
-to that file to enable PEC again.
+So, as not everyone might enjoy the slowdown, PEC is disabled by default and
+can be enabled through sysfs. Just write 1 to the "pec" file and PEC will be
+enabled. Write 0 to that file to disable PEC again.
diff --git a/drivers/hwmon/lm90.c b/drivers/hwmon/lm90.c
index 995b27a248e6..8ba95ea06f0c 100644
--- a/drivers/hwmon/lm90.c
+++ b/drivers/hwmon/lm90.c
@@ -179,6 +179,8 @@ enum chips { adm1032, adt7461, g781, lm86, lm90, lm99,
#define LM90_PAUSE_FOR_CONFIG BIT(9) /* Pause conversion for config */
#define LM90_HAVE_CRIT BIT(10) /* Chip supports CRIT/OVERT register */
#define LM90_HAVE_CRIT_ALRM_SWP BIT(11) /* critical alarm bits swapped */
+#define LM90_HAVE_PEC BIT(12) /* Chip supports PEC */
+#define LM90_HAVE_PARTIAL_PEC BIT(13) /* Partial PEC support (adm1032)*/

/* LM90 status */
#define LM90_STATUS_LTHRM BIT(0) /* local THERM limit tripped */
@@ -346,7 +348,8 @@ struct lm90_params {
static const struct lm90_params lm90_params[] = {
[adm1032] = {
.flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT
- | LM90_HAVE_BROKEN_ALERT | LM90_HAVE_CRIT,
+ | LM90_HAVE_BROKEN_ALERT | LM90_HAVE_CRIT
+ | LM90_HAVE_PARTIAL_PEC,
.alert_alarms = 0x7c,
.max_convrate = 10,
},
@@ -519,10 +522,10 @@ struct lm90_data {
*/

/*
- * The ADM1032 supports PEC but not on write byte transactions, so we need
+ * If the chip supports PEC but not on write byte transactions, we need
* to explicitly ask for a transaction without PEC.
*/
-static inline s32 adm1032_write_byte(struct i2c_client *client, u8 value)
+static inline s32 lm90_write_no_pec(struct i2c_client *client, u8 value)
{
return i2c_smbus_xfer(client->adapter, client->addr,
client->flags & ~I2C_CLIENT_PEC,
@@ -531,22 +534,24 @@ static inline s32 adm1032_write_byte(struct i2c_client *client, u8 value)

/*
* It is assumed that client->update_lock is held (unless we are in
- * detection or initialization steps). This matters when PEC is enabled,
- * because we don't want the address pointer to change between the write
- * byte and the read byte transactions.
+ * detection or initialization steps). This matters when PEC is enabled
+ * for chips with partial PEC support, because we don't want the address
+ * pointer to change between the write byte and the read byte transactions.
*/
static int lm90_read_reg(struct i2c_client *client, u8 reg)
{
+ struct lm90_data *data = i2c_get_clientdata(client);
+ bool partial_pec = (client->flags & I2C_CLIENT_PEC) &&
+ (data->flags & LM90_HAVE_PARTIAL_PEC);
int err;

- if (client->flags & I2C_CLIENT_PEC) {
- err = adm1032_write_byte(client, reg);
- if (err >= 0)
- err = i2c_smbus_read_byte(client);
- } else
- err = i2c_smbus_read_byte_data(client, reg);
-
- return err;
+ if (partial_pec) {
+ err = lm90_write_no_pec(client, reg);
+ if (err)
+ return err;
+ return i2c_smbus_read_byte(client);
+ }
+ return i2c_smbus_read_byte_data(client, reg);
}

/*
@@ -1135,7 +1140,7 @@ static u16 temp_to_u16_adt7461(struct lm90_data *data, long val)
return (val + 125) / 250 * 64;
}

-/* pec used for ADM1032 only */
+/* pec used for devices with PEC support */
static ssize_t pec_show(struct device *dev, struct device_attribute *dummy,
char *buf)
{
@@ -1675,13 +1680,6 @@ static int lm90_detect(struct i2c_client *client,
&& (config1 & 0x3F) == 0x00
&& convrate <= 0x0A) {
name = "adm1032";
- /*
- * The ADM1032 supports PEC, but only if combined
- * transactions are not used.
- */
- if (i2c_check_functionality(adapter,
- I2C_FUNC_SMBUS_BYTE))
- info->flags |= I2C_CLIENT_PEC;
} else
if (chip_id == 0x51 /* ADT7461 */
&& (config1 & 0x1B) == 0x00
@@ -2005,10 +2003,6 @@ static int lm90_probe(struct i2c_client *client)
data->kind = (enum chips)of_device_get_match_data(&client->dev);
else
data->kind = i2c_match_id(lm90_id, client)->driver_data;
- if (data->kind == adm1032) {
- if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE))
- client->flags &= ~I2C_CLIENT_PEC;
- }

/*
* Different devices have different alarm bits triggering the
@@ -2019,6 +2013,14 @@ static int lm90_probe(struct i2c_client *client)
/* Set chip capabilities */
data->flags = lm90_params[data->kind].flags;

+ if ((data->flags & (LM90_HAVE_PEC | LM90_HAVE_PARTIAL_PEC)) &&
+ !i2c_check_functionality(adapter, I2C_FUNC_SMBUS_PEC))
+ data->flags &= ~(LM90_HAVE_PEC | LM90_HAVE_PARTIAL_PEC);
+
+ if ((data->flags & LM90_HAVE_PARTIAL_PEC) &&
+ !i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE))
+ data->flags &= ~LM90_HAVE_PARTIAL_PEC;
+
data->chip.ops = &lm90_ops;
data->chip.info = data->info;

@@ -2081,7 +2083,7 @@ static int lm90_probe(struct i2c_client *client)
* The 'pec' attribute is attached to the i2c device and thus created
* separately.
*/
- if (client->flags & I2C_CLIENT_PEC) {
+ if (data->flags & (LM90_HAVE_PEC | LM90_HAVE_PARTIAL_PEC)) {
err = device_create_file(dev, &dev_attr_pec);
if (err)
return err;
--
2.35.1
\
 
 \ /
  Last update: 2022-05-25 16:00    [W:1.219 / U:0.108 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site