lkml.org 
[lkml]   [2022]   [May]   [25]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
SubjectRe: [PATCH v2] ARM: dts: aspeed: Adding Jabil Rubypass BMC
From
On 25/05/2022 05:42, David Wang wrote:
> The initial introduction of the jabil server with AST2600 BMC SoC.
>
> ---
>
> v2
> - Disable empty i2c bus.
> - Remove gfx node because aspeed-g6.dtsi isn't supported.
> - Modify the led format and add some properties.
> - Fix wrong indentation.
> - Add stdout property in chosen node.
> - Rename temp to temperature-sensor in i2c bus 0.
>
> ---
>
> Signed-off-by: David Wang <David_Wang6097@jabil.com>
> ---
> arch/arm/boot/dts/Makefile | 3 +-
> .../boot/dts/aspeed-bmc-jabil-rubypass.dts | 449 ++++++++++++++++++
> 2 files changed, 451 insertions(+), 1 deletion(-)
> create mode 100644 arch/arm/boot/dts/aspeed-bmc-jabil-rubypass.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 7c16f8a2b738..9c395178fc89 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -1566,4 +1566,5 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
> aspeed-bmc-tyan-s8036.dtb \
> aspeed-bmc-vegman-n110.dtb \
> aspeed-bmc-vegman-rx20.dtb \
> - aspeed-bmc-vegman-sx20.dtb
> + aspeed-bmc-vegman-sx20.dtb \
> + aspeed-bmc-jabil-rubypass.dtb

The entries are ordered by name and your new name looks out of order...

> diff --git a/arch/arm/boot/dts/aspeed-bmc-jabil-rubypass.dts b/arch/arm/boot/dts/aspeed-bmc-jabil-rubypass.dts
> new file mode 100644
> index 000000000000..0e1450f66372
> --- /dev/null
> +++ b/arch/arm/boot/dts/aspeed-bmc-jabil-rubypass.dts
> @@ -0,0 +1,449 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later
> +
> +/dts-v1/;
> +
> +#include "aspeed-g6.dtsi"
> +#include <dt-bindings/gpio/aspeed-gpio.h>
> +#include <dt-bindings/leds/common.h>
> +
> +/ {
> + model = "Jabil rbp";
> + compatible = "aspeed,ast2600";
> +
> + chosen {
> + stdout-path = &uart5;
> + bootargs = "console=ttyS4,115200n8";

You do not need bootargs. Use stdout-path.

> + };
> +
> + memory@80000000 {
> + device_type = "memory";
> + reg = <0x80000000 0x80000000>;
> + };
> +
> + vcc_sdhci0: regulator-vcc-sdhci0 {
> + compatible = "regulator-fixed";
> + regulator-name = "SDHCI0 Vcc";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpios = <&gpio0 ASPEED_GPIO(V, 0) GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +
> +
> + vccq_sdhci0: regulator-vccq-sdhci0 {
> + compatible = "regulator-gpio";
> + regulator-name = "SDHCI0 VccQ";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + gpios = <&gpio0 ASPEED_GPIO(V, 1) GPIO_ACTIVE_HIGH>;
> + gpios-states = <1>;
> + states = <3300000 1>,
> + <1800000 0>;
> + };
> +
> + vcc_sdhci1: regulator-vcc-sdhci1 {
> + compatible = "regulator-fixed";
> + regulator-name = "SDHCI1 Vcc";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpios = <&gpio0 ASPEED_GPIO(V, 2) GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +
> + vccq_sdhci1: regulator-vccq-sdhci1 {
> + compatible = "regulator-gpio";
> + regulator-name = "SDHCI1 VccQ";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + gpios = <&gpio0 ASPEED_GPIO(V, 3) GPIO_ACTIVE_HIGH>;
> + gpios-states = <1>;
> + states = <3300000 1>,
> + <1800000 0>;
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> + pinctrl-names = "default";
> +
> + led-0 {
> + label = "identify";
> + color = <LED_COLOR_ID_BLUE>;
> + function = LED_FUNCTION_INDICATOR;
> + retain-state-shutdown;
> + gpios = <&gpio0 ASPEED_GPIO(B, 7) GPIO_ACTIVE_LOW>;
> + };
> +
> + led-1 {
> + label = "status_amber";
> + color = <LED_COLOR_ID_AMBER>;
> + function = LED_FUNCTION_STATUS;
> + gpios = <&gpio0 ASPEED_GPIO(G, 3) GPIO_ACTIVE_LOW>;
> + };
> +
> + led-2 {
> + label = "status_green";
> + color = <LED_COLOR_ID_GREEN>;
> + default-state = "keep";
> + function = LED_FUNCTION_STATUS;
> + gpios = <&gpio0 ASPEED_GPIO(G, 2) GPIO_ACTIVE_LOW>;
> + };
> +
> + led-3 {
> + label = "status_susack";
> + function = LED_FUNCTION_STATUS;
> + gpios = <&gpio0 ASPEED_GPIO(V, 6) GPIO_ACTIVE_LOW>;
> + };
> +
> + led-4{
> + label = "power-amber";
> + color = <LED_COLOR_ID_AMBER>;
> + function = LED_FUNCTION_POWER;
> + gpios = <&gpio0 ASPEED_GPIO(Y, 0) GPIO_ACTIVE_LOW>;
> + };
> + };
> +
> + fan_fault {

No underscores in node names, generic node names, so leds-1 (and
previous leds-0). Although main question - why do you need two instances
of drivers?

> + compatible = "gpio-leds";
> + pinctrl-names = "default";
> +
> + led-0 {
> + label = "fan1-fault";
> + color = <LED_COLOR_ID_YELLOW>;
> + function = LED_FUNCTION_FAULT;
> + retain-state-shutdown;
> + gpios = <&gpio3_71 0 GPIO_ACTIVE_HIGH>;
> + };
> +
> + led-1 {
> + label = "fan2-fault";
> + color = <LED_COLOR_ID_YELLOW>;
> + function = LED_FUNCTION_FAULT;
> + retain-state-shutdown;
> + gpios = <&gpio3_71 1 GPIO_ACTIVE_HIGH>;
> + };
> +
> + led-2 {
> + label = "fan3-fault";
> + color = <LED_COLOR_ID_YELLOW>;
> + function = LED_FUNCTION_FAULT;
> + retain-state-shutdown;
> + gpios = <&gpio3_71 2 GPIO_ACTIVE_HIGH>;
> + };
> +
> + led-3 {
> + label = "fan4-fault";
> + color = <LED_COLOR_ID_YELLOW>;
> + function = LED_FUNCTION_FAULT;
> + retain-state-shutdown;
> + gpios = <&gpio3_71 3 GPIO_ACTIVE_HIGH>;
> + };
> +
> + led-4 {
> + label = "fan5-fault";
> + color = <LED_COLOR_ID_YELLOW>;
> + function = LED_FUNCTION_FAULT;
> + retain-state-shutdown;
> + gpios = <&gpio3_71 4 GPIO_ACTIVE_HIGH>;
> + };
> +
> + led-5 {
> + label = "fan6-fault";
> + color = <LED_COLOR_ID_YELLOW>;
> + function = LED_FUNCTION_FAULT;
> + retain-state-shutdown;
> + gpios = <&gpio3_71 5 GPIO_ACTIVE_HIGH>;
> + };
> + };
> +};
> +
> +&mdio0 {
> + status = "okay";
> +
> + ethphy0: ethernet-phy@0 {
> + compatible = "ethernet-phy-ieee802.3-c22";
> + reg = <0>;
> + };
> +};
> +
> +&mdio1 {
> + status = "okay";
> +
> + ethphy1: ethernet-phy@0 {
> + compatible = "ethernet-phy-ieee802.3-c22";
> + reg = <0>;
> + };
> +};
> +
> +&mdio2 {
> + status = "okay";
> +
> + ethphy2: ethernet-phy@0 {
> + compatible = "ethernet-phy-ieee802.3-c22";
> + reg = <0>;
> + };
> +};
> +
> +&mdio3 {
> + status = "okay";
> +
> + ethphy3: ethernet-phy@0 {
> + compatible = "ethernet-phy-ieee802.3-c22";
> + reg = <0>;
> + };
> +};
> +
> +&mac0 {
> + status = "okay";
> +
> + phy-mode = "rgmii-rxid";
> + phy-handle = <&ethphy0>;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_rgmii1_default>;
> +};
> +
> +&mac1 {
> + status = "okay";
> +
> + phy-mode = "rgmii-rxid";
> + phy-handle = <&ethphy1>;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_rgmii2_default>;
> +};
> +
> +&mac2 {
> + status = "okay";
> +
> + phy-mode = "rgmii";
> + phy-handle = <&ethphy2>;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_rgmii3_default>;
> +};
> +
> +&mac3 {
> + status = "okay";
> +
> + phy-mode = "rgmii";
> + phy-handle = <&ethphy3>;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_rgmii4_default>;
> +};
> +
> +&emmc_controller {
> + status = "okay";
> +};
> +
> +&emmc {
> + non-removable;
> + bus-width = <4>;
> + max-frequency = <100000000>;
> + clk-phase-mmc-hs200 = <9>, <225>;
> +};
> +
> +&rtc {
> + status = "okay";
> +};
> +
> +&fmc {
> + status = "okay";
> + flash@0 {
> + status = "okay";
> + m25p,fast-read;
> + label = "bmc";
> + spi-max-frequency = <50000000>;
> +#include "openbmc-flash-layout-128.dtsi"
> + };
> +};
> +
> +&spi1 {
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_spi1_default>;
> +
> + flash@0 {
> + status = "okay";
> + m25p,fast-read;
> + label = "pnor";
> + spi-max-frequency = <100000000>;
> + };
> +};
> +
> +&uart1 {
> + status = "okay";
> + pinctrl-0 = <&pinctrl_txd1_default
> + &pinctrl_rxd1_default
> + &pinctrl_nrts1_default
> + &pinctrl_ndtr1_default
> + &pinctrl_ndsr1_default
> + &pinctrl_ncts1_default
> + &pinctrl_ndcd1_default
> + &pinctrl_nri1_default>;
> +};
> +
> +&uart2 {
> + status = "okay";
> + pinctrl-0 = <&pinctrl_txd2_default
> + &pinctrl_rxd2_default
> + &pinctrl_nrts2_default
> + &pinctrl_ndtr2_default
> + &pinctrl_ndsr2_default
> + &pinctrl_ncts2_default
> + &pinctrl_ndcd2_default
> + &pinctrl_nri2_default>;
> +};
> +
> +&uart3 {
> + status = "okay";
> +};
> +
> +&uart4 {
> + status = "okay";
> +};
> +
> +&i2c0 {
> + status = "okay";
> +
> + temperature-sensor@2e {
> + compatible = "adi,adt7490";
> + reg = <0x2e>;
> + };
> +};
> +
> +&i2c3 {
> + multi-master;
> + status = "okay";
> +
> + gpio@70 {
> + compatible = "nxp,pca9538";
> + reg = <0x70>;
> + interrupt-parent = <&gpio0>;
> + interrupts = <ASPEED_GPIO(O, 7) IRQ_TYPE_EDGE_FALLING>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + gpio-line-names =
> + "presence-fan1-n", "presence-fan2-n", "presence-fan3-n", "presence-fan4-n",
> + "presence-fan5-n", "presence-fan6-n", "", "";
> + };
> +
> + gpio3_71:gpio@71 {

Missing space after :.

> + compatible = "nxp,pca9538";
> + reg = <0x71>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + gpio-line-names =
> + "led-fan1-fault", "led-fan2-fault", "led-fan3-fault", "led-fan4-fault",
> + "led-fan5-fault", "led-fan6-fault", "", "";
> + };
> +};
> +
> +&fsim0 {
> + status = "okay";
> +};
> +
> +&ehci1 {
> + status = "okay";
> +};
> +
> +&uhci {
> + status = "okay";
> +};
> +
> +&sdc {
> + status = "okay";
> +};
> +
> +/*
> + * The signal voltage of sdhci0 and sdhci1 on AST2600-A2 EVB is able to be
> + * toggled by GPIO pins.
> + * In the reference design, GPIOV0 of AST2600-A2 EVB is connected to the
> + * power load switch that provides 3.3v to sdhci0 vdd, GPIOV1 is connected to
> + * a 1.8v and a 3.3v power load switch that provides signal voltage to
> + * sdhci0 bus.
> + * If GPIOV0 is active high, sdhci0 is enabled, otherwise, sdhci0 is disabled.
> + * If GPIOV1 is active high, 3.3v power load switch is enabled, sdhci0 signal
> + * voltage is 3.3v, otherwise, 1.8v power load switch will be enabled,
> + * sdhci0 signal voltage becomes 1.8v.
> + * AST2600-A2 EVB also supports toggling signal voltage for sdhci1.
> + * The design is the same as sdhci0, it uses GPIOV2 as power-gpio and GPIOV3
> + * as power-switch-gpio.
> + */
> +&sdhci0 {
> + status = "okay";
> + bus-width = <4>;
> + max-frequency = <100000000>;
> + sdhci-drive-type = /bits/ 8 <3>;
> + sdhci-caps-mask = <0x7 0x0>;
> + sdhci,wp-inverted;
> + vmmc-supply = <&vcc_sdhci0>;
> + vqmmc-supply = <&vccq_sdhci0>;
> + clk-phase-sd-hs = <7>, <200>;
> +};
> +
> +&sdhci1 {
> + status = "okay";
> + bus-width = <4>;
> + max-frequency = <100000000>;
> + sdhci-drive-type = /bits/ 8 <3>;
> + sdhci-caps-mask = <0x7 0x0>;
> + sdhci,wp-inverted;
> + vmmc-supply = <&vcc_sdhci1>;
> + vqmmc-supply = <&vccq_sdhci1>;
> + clk-phase-sd-hs = <7>, <200>;
> +};
> +
> +&gpio0 {
> + status = "okay";
> + gpio-line-names =
> + /*A0-A7*/ "","","","","","","","",
> + /*B0-B7*/ "presence-ncsi-i210-n","","","","","","","led-identify-n",
> + /*C0-C7*/ "","","","","","","","",
> + /*D0-D7*/ "","","","","","","","",
> + /*E0-E7*/ "","","","","","","","",
> + /*F0-F7*/ "","","","","","","id-button","",
> + /*G0-G7*/ "","","led-status-green-n","led-status-amber-n","","","","",
> + /*H0-H7*/ "","","","","","cpu-caterr","","cpu1-caterr-n",
> + /*I0-I7*/ "","","","","","","","",
> + /*J0-J7*/ "","","","","","","","",
> + /*K0-K7*/ "","","","","","","","",
> + /*L0-L7*/ "","","","","","","","",
> + /*M0-M7*/ "","","","","","","","",
> + /*N0-N7*/ "","","","","","","","",
> + /*O0-O7*/ "","","","","","","nmi-button","",
> + /*P0-P7*/ "reset-button","reset-out","power-button","power-out","","","",
> + "led-hartbeat-n",
> + /*Q0-Q7*/ "","","","","","","","",
> + /*R0-R7*/ "","","","","","","","",
> + /*S0-S7*/ "","","","","","","","",
> + /*T0-T7*/ "","","","","","","","",
> + /*U0-U7*/ "","","","","","","","",
> + /*V0-V7*/ "regulator-vcc-sdhci0","regulator-vccq-sdhci0","regulator-vcc-sdhci1",
> + "regulator-vccq-sdhci1","sio-power-good",
> + "led-bmc-fw-config-done-n","","",
> + /*W0-W7*/ "","","","","","","","",
> + /*X0-X7*/ "cpu-err2","","","","","","","",
> + /*Y0-Y7*/ "led-power-amber","","","","","","","",
> + /*Z0-Z7*/ "cpu-err0","cpu-err1","","","","","","";
> + };
> +
> +&gpio1 {
> + status = "okay";
> +};
> +
> +&kcs3 {
> + aspeed,lpc-io-reg = <0xCA2>;
> + status = "okay";
> +};
> +
> +&kcs4 {
> + aspeed,lpc-io-reg = <0xCA4>;
> + status = "okay";
> +};
> +
> +&lpc_snoop {
> + snoop-ports = <0x80>;
> + status = "okay";
> +};
> +

Unneeded blank line at the end.

Best regards,
Krzysztof

\
 
 \ /
  Last update: 2022-05-25 08:17    [W:0.054 / U:0.364 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site