lkml.org 
[lkml]   [2022]   [May]   [25]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v3] ARM: dts: aspeed: Adding Jabil Rubypass BMC
Date
The initial introduction of the jabil server with AST2600 BMC SoC.

---

v3
- Adjustment entries are ordered by name.
- Remove the bootargs property and modify the stdout-path property.
- Group multiple LED devices into a group.
- Modify the "gpio3_71" node name format.
- Delete unneeded blank line at the end.

v2
- Disable empty i2c bus.
- Remove gfx node because aspeed-g6.dtsi isn't supported.
- Modify the led format and add some properties.
- Fix wrong indentation.
- Add stdout property in chosen node.
- Rename temp to temperature-sensor in i2c bus 0.

---

Signed-off-by: David Wang <David_Wang6097@jabil.com>
---
arch/arm/boot/dts/Makefile | 1 +
.../boot/dts/aspeed-bmc-jabil-rubypass.dts | 442 ++++++++++++++++++
2 files changed, 443 insertions(+)
create mode 100644 arch/arm/boot/dts/aspeed-bmc-jabil-rubypass.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 7c16f8a2b738..5339e9339ce4 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1543,6 +1543,7 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
aspeed-bmc-intel-s2600wf.dtb \
aspeed-bmc-inspur-fp5280g2.dtb \
aspeed-bmc-inspur-nf5280m6.dtb \
+ aspeed-bmc-jabil-rubypass.dtb \
aspeed-bmc-lenovo-hr630.dtb \
aspeed-bmc-lenovo-hr855xg2.dtb \
aspeed-bmc-microsoft-olympus.dtb \
diff --git a/arch/arm/boot/dts/aspeed-bmc-jabil-rubypass.dts b/arch/arm/boot/dts/aspeed-bmc-jabil-rubypass.dts
new file mode 100644
index 000000000000..3a835f31a1b2
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed-bmc-jabil-rubypass.dts
@@ -0,0 +1,442 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+
+/dts-v1/;
+
+#include "aspeed-g6.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+ model = "Jabil rbp";
+ compatible = "aspeed,ast2600";
+
+ chosen {
+ stdout-path = "/uart5:115200n8";
+ };
+
+ memory@80000000 {
+ device_type = "memory";
+ reg = <0x80000000 0x80000000>;
+ };
+
+ vcc_sdhci0: regulator-vcc-sdhci0 {
+ compatible = "regulator-fixed";
+ regulator-name = "SDHCI0 Vcc";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpios = <&gpio0 ASPEED_GPIO(V, 0) GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+
+ vccq_sdhci0: regulator-vccq-sdhci0 {
+ compatible = "regulator-gpio";
+ regulator-name = "SDHCI0 VccQ";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ gpios = <&gpio0 ASPEED_GPIO(V, 1) GPIO_ACTIVE_HIGH>;
+ gpios-states = <1>;
+ states = <3300000 1>,
+ <1800000 0>;
+ };
+
+ vcc_sdhci1: regulator-vcc-sdhci1 {
+ compatible = "regulator-fixed";
+ regulator-name = "SDHCI1 Vcc";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpios = <&gpio0 ASPEED_GPIO(V, 2) GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ vccq_sdhci1: regulator-vccq-sdhci1 {
+ compatible = "regulator-gpio";
+ regulator-name = "SDHCI1 VccQ";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ gpios = <&gpio0 ASPEED_GPIO(V, 3) GPIO_ACTIVE_HIGH>;
+ gpios-states = <1>;
+ states = <3300000 1>,
+ <1800000 0>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+
+ led-0 {
+ label = "identify";
+ color = <LED_COLOR_ID_BLUE>;
+ function = LED_FUNCTION_INDICATOR;
+ retain-state-shutdown;
+ gpios = <&gpio0 ASPEED_GPIO(B, 7) GPIO_ACTIVE_LOW>;
+ };
+
+ led-1 {
+ label = "status_amber";
+ color = <LED_COLOR_ID_AMBER>;
+ function = LED_FUNCTION_STATUS;
+ gpios = <&gpio0 ASPEED_GPIO(G, 3) GPIO_ACTIVE_LOW>;
+ };
+
+ led-2 {
+ label = "status_green";
+ color = <LED_COLOR_ID_GREEN>;
+ default-state = "keep";
+ function = LED_FUNCTION_STATUS;
+ gpios = <&gpio0 ASPEED_GPIO(G, 2) GPIO_ACTIVE_LOW>;
+ };
+
+ led-3 {
+ label = "status_susack";
+ function = LED_FUNCTION_STATUS;
+ gpios = <&gpio0 ASPEED_GPIO(V, 6) GPIO_ACTIVE_LOW>;
+ };
+
+ led-4{
+ label = "power-amber";
+ color = <LED_COLOR_ID_AMBER>;
+ function = LED_FUNCTION_POWER;
+ gpios = <&gpio0 ASPEED_GPIO(Y, 0) GPIO_ACTIVE_LOW>;
+ };
+
+ led-5 {
+ label = "fan1-fault";
+ color = <LED_COLOR_ID_YELLOW>;
+ function = LED_FUNCTION_FAULT;
+ retain-state-shutdown;
+ gpios = <&gpio3_71 0 GPIO_ACTIVE_HIGH>;
+ };
+
+ led-6 {
+ label = "fan2-fault";
+ color = <LED_COLOR_ID_YELLOW>;
+ function = LED_FUNCTION_FAULT;
+ retain-state-shutdown;
+ gpios = <&gpio3_71 1 GPIO_ACTIVE_HIGH>;
+ };
+
+ led-7 {
+ label = "fan3-fault";
+ color = <LED_COLOR_ID_YELLOW>;
+ function = LED_FUNCTION_FAULT;
+ retain-state-shutdown;
+ gpios = <&gpio3_71 2 GPIO_ACTIVE_HIGH>;
+ };
+
+ led-8 {
+ label = "fan4-fault";
+ color = <LED_COLOR_ID_YELLOW>;
+ function = LED_FUNCTION_FAULT;
+ retain-state-shutdown;
+ gpios = <&gpio3_71 3 GPIO_ACTIVE_HIGH>;
+ };
+
+ led-9 {
+ label = "fan5-fault";
+ color = <LED_COLOR_ID_YELLOW>;
+ function = LED_FUNCTION_FAULT;
+ retain-state-shutdown;
+ gpios = <&gpio3_71 4 GPIO_ACTIVE_HIGH>;
+ };
+
+ led-10 {
+ label = "fan6-fault";
+ color = <LED_COLOR_ID_YELLOW>;
+ function = LED_FUNCTION_FAULT;
+ retain-state-shutdown;
+ gpios = <&gpio3_71 5 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
+
+&mdio0 {
+ status = "okay";
+
+ ethphy0: ethernet-phy@0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
+ };
+};
+
+&mdio1 {
+ status = "okay";
+
+ ethphy1: ethernet-phy@0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
+ };
+};
+
+&mdio2 {
+ status = "okay";
+
+ ethphy2: ethernet-phy@0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
+ };
+};
+
+&mdio3 {
+ status = "okay";
+
+ ethphy3: ethernet-phy@0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
+ };
+};
+
+&mac0 {
+ status = "okay";
+
+ phy-mode = "rgmii-rxid";
+ phy-handle = <&ethphy0>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_rgmii1_default>;
+};
+
+&mac1 {
+ status = "okay";
+
+ phy-mode = "rgmii-rxid";
+ phy-handle = <&ethphy1>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_rgmii2_default>;
+};
+
+&mac2 {
+ status = "okay";
+
+ phy-mode = "rgmii";
+ phy-handle = <&ethphy2>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_rgmii3_default>;
+};
+
+&mac3 {
+ status = "okay";
+
+ phy-mode = "rgmii";
+ phy-handle = <&ethphy3>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_rgmii4_default>;
+};
+
+&emmc_controller {
+ status = "okay";
+};
+
+&emmc {
+ non-removable;
+ bus-width = <4>;
+ max-frequency = <100000000>;
+ clk-phase-mmc-hs200 = <9>, <225>;
+};
+
+&rtc {
+ status = "okay";
+};
+
+&fmc {
+ status = "okay";
+ flash@0 {
+ status = "okay";
+ m25p,fast-read;
+ label = "bmc";
+ spi-max-frequency = <50000000>;
+#include "openbmc-flash-layout-128.dtsi"
+ };
+};
+
+&spi1 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_spi1_default>;
+
+ flash@0 {
+ status = "okay";
+ m25p,fast-read;
+ label = "pnor";
+ spi-max-frequency = <100000000>;
+ };
+};
+
+&uart1 {
+ status = "okay";
+ pinctrl-0 = <&pinctrl_txd1_default
+ &pinctrl_rxd1_default
+ &pinctrl_nrts1_default
+ &pinctrl_ndtr1_default
+ &pinctrl_ndsr1_default
+ &pinctrl_ncts1_default
+ &pinctrl_ndcd1_default
+ &pinctrl_nri1_default>;
+};
+
+&uart2 {
+ status = "okay";
+ pinctrl-0 = <&pinctrl_txd2_default
+ &pinctrl_rxd2_default
+ &pinctrl_nrts2_default
+ &pinctrl_ndtr2_default
+ &pinctrl_ndsr2_default
+ &pinctrl_ncts2_default
+ &pinctrl_ndcd2_default
+ &pinctrl_nri2_default>;
+};
+
+&uart3 {
+ status = "okay";
+};
+
+&uart4 {
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+
+ temperature-sensor@2e {
+ compatible = "adi,adt7490";
+ reg = <0x2e>;
+ };
+};
+
+&i2c3 {
+ multi-master;
+ status = "okay";
+
+ gpio@70 {
+ compatible = "nxp,pca9538";
+ reg = <0x70>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <ASPEED_GPIO(O, 7) IRQ_TYPE_EDGE_FALLING>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-line-names =
+ "presence-fan1-n", "presence-fan2-n", "presence-fan3-n", "presence-fan4-n",
+ "presence-fan5-n", "presence-fan6-n", "", "";
+ };
+
+ gpio3_71: gpio@71 {
+ compatible = "nxp,pca9538";
+ reg = <0x71>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-line-names =
+ "led-fan1-fault", "led-fan2-fault", "led-fan3-fault", "led-fan4-fault",
+ "led-fan5-fault", "led-fan6-fault", "", "";
+ };
+};
+
+&fsim0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&uhci {
+ status = "okay";
+};
+
+&sdc {
+ status = "okay";
+};
+
+/*
+ * The signal voltage of sdhci0 and sdhci1 on AST2600-A2 EVB is able to be
+ * toggled by GPIO pins.
+ * In the reference design, GPIOV0 of AST2600-A2 EVB is connected to the
+ * power load switch that provides 3.3v to sdhci0 vdd, GPIOV1 is connected to
+ * a 1.8v and a 3.3v power load switch that provides signal voltage to
+ * sdhci0 bus.
+ * If GPIOV0 is active high, sdhci0 is enabled, otherwise, sdhci0 is disabled.
+ * If GPIOV1 is active high, 3.3v power load switch is enabled, sdhci0 signal
+ * voltage is 3.3v, otherwise, 1.8v power load switch will be enabled,
+ * sdhci0 signal voltage becomes 1.8v.
+ * AST2600-A2 EVB also supports toggling signal voltage for sdhci1.
+ * The design is the same as sdhci0, it uses GPIOV2 as power-gpio and GPIOV3
+ * as power-switch-gpio.
+ */
+&sdhci0 {
+ status = "okay";
+ bus-width = <4>;
+ max-frequency = <100000000>;
+ sdhci-drive-type = /bits/ 8 <3>;
+ sdhci-caps-mask = <0x7 0x0>;
+ sdhci,wp-inverted;
+ vmmc-supply = <&vcc_sdhci0>;
+ vqmmc-supply = <&vccq_sdhci0>;
+ clk-phase-sd-hs = <7>, <200>;
+};
+
+&sdhci1 {
+ status = "okay";
+ bus-width = <4>;
+ max-frequency = <100000000>;
+ sdhci-drive-type = /bits/ 8 <3>;
+ sdhci-caps-mask = <0x7 0x0>;
+ sdhci,wp-inverted;
+ vmmc-supply = <&vcc_sdhci1>;
+ vqmmc-supply = <&vccq_sdhci1>;
+ clk-phase-sd-hs = <7>, <200>;
+};
+
+&gpio0 {
+ status = "okay";
+ gpio-line-names =
+ /*A0-A7*/ "","","","","","","","",
+ /*B0-B7*/ "presence-ncsi-i210-n","","","","","","","led-identify-n",
+ /*C0-C7*/ "","","","","","","","",
+ /*D0-D7*/ "","","","","","","","",
+ /*E0-E7*/ "","","","","","","","",
+ /*F0-F7*/ "","","","","","","id-button","",
+ /*G0-G7*/ "","","led-status-green-n","led-status-amber-n","","","","",
+ /*H0-H7*/ "","","","","","cpu-caterr","","cpu1-caterr-n",
+ /*I0-I7*/ "","","","","","","","",
+ /*J0-J7*/ "","","","","","","","",
+ /*K0-K7*/ "","","","","","","","",
+ /*L0-L7*/ "","","","","","","","",
+ /*M0-M7*/ "","","","","","","","",
+ /*N0-N7*/ "","","","","","","","",
+ /*O0-O7*/ "","","","","","","nmi-button","",
+ /*P0-P7*/ "reset-button","reset-out","power-button","power-out","","","",
+ "led-hartbeat-n",
+ /*Q0-Q7*/ "","","","","","","","",
+ /*R0-R7*/ "","","","","","","","",
+ /*S0-S7*/ "","","","","","","","",
+ /*T0-T7*/ "","","","","","","","",
+ /*U0-U7*/ "","","","","","","","",
+ /*V0-V7*/ "regulator-vcc-sdhci0","regulator-vccq-sdhci0","regulator-vcc-sdhci1",
+ "regulator-vccq-sdhci1","sio-power-good",
+ "led-bmc-fw-config-done-n","","",
+ /*W0-W7*/ "","","","","","","","",
+ /*X0-X7*/ "cpu-err2","","","","","","","",
+ /*Y0-Y7*/ "led-power-amber","","","","","","","",
+ /*Z0-Z7*/ "cpu-err0","cpu-err1","","","","","","";
+ };
+
+&gpio1 {
+ status = "okay";
+};
+
+&kcs3 {
+ aspeed,lpc-io-reg = <0xCA2>;
+ status = "okay";
+};
+
+&kcs4 {
+ aspeed,lpc-io-reg = <0xCA4>;
+ status = "okay";
+};
+
+&lpc_snoop {
+ snoop-ports = <0x80>;
+ status = "okay";
+};
\ No newline at end of file
--
2.30.2
\
 
 \ /
  Last update: 2022-05-25 11:41    [W:0.100 / U:0.968 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site