lkml.org 
[lkml]   [2022]   [May]   [24]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH] arm64: dts: qcom: sc7280: Add touchscreen to villager
Date
This adds the touchscreen to the sc7280-herobrine-villager device
tree. Note that the touchscreen on villager actually uses the reset
line and thus we use the more specific "elan,ekth6915" compatible
which allows us to specify the reset.

The fact that villager's touchscreen uses the reset line can be
contrasted against the touchscreen for CRD/herobrine-r1. On those
boards, even though the touchscreen goes to the display, it's not
hooked up to anything there.

In order to keep the line parked on herobrine/CRD, we'll move the
pullup from the qcard.dtsi file to the specific boards. This allows us
to disable the pullup in the villager device tree since the pin is an
output.

Signed-off-by: Douglas Anderson <dianders@chromium.org>
---
This uses bindings introduced in the patch ("dt-bindings: HID:
i2c-hid: elan: Introduce bindings for Elan eKTH6915") [1].

[1] https://lore.kernel.org/r/20220523142257.v2.1.Iedc61f9ef220a89af6a031200a7850a27a440134@changeid

.../boot/dts/qcom/sc7280-herobrine-crd.dts | 11 ++++++++
.../qcom/sc7280-herobrine-herobrine-r1.dts | 11 ++++++++
.../dts/qcom/sc7280-herobrine-villager-r0.dts | 25 +++++++++++++++++++
arch/arm64/boot/dts/qcom/sc7280-qcard.dtsi | 1 -
4 files changed, 47 insertions(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/qcom/sc7280-herobrine-crd.dts b/arch/arm64/boot/dts/qcom/sc7280-herobrine-crd.dts
index a4ac33c4fd59..b79d84d7870a 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-herobrine-crd.dts
+++ b/arch/arm64/boot/dts/qcom/sc7280-herobrine-crd.dts
@@ -134,6 +134,17 @@ &sdhc_2 {
status = "okay";
};

+/* PINCTRL - ADDITIONS TO NODES IN PARENT DEVICE TREE FILES */
+
+/*
+ * This pin goes to the display panel but then doesn't actually do anything
+ * on the panel itself (it doesn't connect to the touchscreen controller).
+ * We'll set a pullup here just to park the line.
+ */
+&ts_rst_conn {
+ bias-pull-up;
+};
+
/* PINCTRL - BOARD-SPECIFIC */

/*
diff --git a/arch/arm64/boot/dts/qcom/sc7280-herobrine-herobrine-r1.dts b/arch/arm64/boot/dts/qcom/sc7280-herobrine-herobrine-r1.dts
index b69ca09d9bfb..c1647a85a371 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-herobrine-herobrine-r1.dts
+++ b/arch/arm64/boot/dts/qcom/sc7280-herobrine-herobrine-r1.dts
@@ -128,6 +128,17 @@ &sdhc_2 {
status = "okay";
};

+/* PINCTRL - ADDITIONS TO NODES IN PARENT DEVICE TREE FILES */
+
+/*
+ * This pin goes to the display panel but then doesn't actually do anything
+ * on the panel itself (it doesn't connect to the touchscreen controller).
+ * We'll set a pullup here just to park the line.
+ */
+&ts_rst_conn {
+ bias-pull-up;
+};
+
/* PINCTRL - BOARD-SPECIFIC */

/*
diff --git a/arch/arm64/boot/dts/qcom/sc7280-herobrine-villager-r0.dts b/arch/arm64/boot/dts/qcom/sc7280-herobrine-villager-r0.dts
index d3d6ffad4eff..950b69448109 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-herobrine-villager-r0.dts
+++ b/arch/arm64/boot/dts/qcom/sc7280-herobrine-villager-r0.dts
@@ -46,6 +46,25 @@ trackpad: trackpad@2c {
};
};

+ts_i2c: &i2c13 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ ap_ts: touchscreen@10 {
+ compatible = "elan,ekth6915";
+ reg = <0x10>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&ts_int_conn>, <&ts_rst_conn>;
+
+ interrupt-parent = <&tlmm>;
+ interrupts = <55 IRQ_TYPE_LEVEL_LOW>;
+
+ reset-gpios = <&tlmm 54 GPIO_ACTIVE_LOW>;
+
+ vcc33-supply = <&ts_avdd>;
+ };
+};
+
&ap_sar_sensor_i2c {
status = "okay";
};
@@ -81,6 +100,12 @@ &sdhc_1 {
status = "okay";
};

+/* PINCTRL - ADDITIONS TO NODES IN PARENT DEVICE TREE FILES */
+
+&ts_rst_conn {
+ bias-disable;
+};
+
/* PINCTRL - BOARD-SPECIFIC */

/*
diff --git a/arch/arm64/boot/dts/qcom/sc7280-qcard.dtsi b/arch/arm64/boot/dts/qcom/sc7280-qcard.dtsi
index d59002d4492e..404936c6bf20 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-qcard.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280-qcard.dtsi
@@ -604,7 +604,6 @@ ts_int_conn: ts-int-conn {
ts_rst_conn: ts-rst-conn {
pins = "gpio54";
function = "gpio";
- bias-pull-up;
drive-strength = <2>;
};
};
--
2.36.1.124.g0e6072fb45-goog
\
 
 \ /
  Last update: 2022-05-24 22:50    [W:0.159 / U:0.248 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site