lkml.org 
[lkml]   [2022]   [May]   [24]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 11/29] rtc: pcf2127: set RTC_FEATURE_ALARM_RES_2S
On Thu, 17 Mar 2022 18:16:17 +0100
Alexandre Belloni <alexandre.belloni@bootlin.com> wrote:

> Hi,
>
> On 17/03/2022 11:28:20-0400, Hugo Villeneuve wrote:
> > On Thu, 10 Mar 2022 21:58:49 +0100
> > Alexandre Belloni <alexandre.belloni@bootlin.com> wrote:
> >
> > > On 10/03/2022 11:09:18-0500, Hugo Villeneuve wrote:
> > > > On Wed, 9 Mar 2022 17:22:42 +0100
> > > > Alexandre Belloni <alexandre.belloni@bootlin.com> wrote:
> > > >
> > > > > The PCF2127 doesn't support UIE because setting an alarm to fire every
> > > > > second confuses the chip and the fastest we can go is an alarm every 2
> > > > > seconds.
> > > >
> > > > Hi Alexandre,
> > > > can you describe what "confuses the chip" means?
> > > >
> > > > In my experimental PCF2131 driver, I activated UIE and it seems to be working fine at 1s intervals, but since it is similar to PCF2127, maybe there is still a problem and I just didn't see it.
> > > >
> > >
> > > Did you remove uie_unsupported? Else, you may have been using uie
> > > emulation. In my tests last year, the pcf2127 was failing to reassert
> > > the interrupt if an alarm was set every second. The same happens on
> > > other NXP based RTCs (i.e. including microcrystal ones).
> > >
> > > I'm going to test again soon (and also reply to your series).
> >
> > Hi,
> > I have now access to a board with a PCF2129T.
> >
>
> I actually did the test again this afternoon with a pcf2127...
>
> > I have been able to test with it by sending ioctl RTC_UIE_ON and
> > confirm that it exhibits the problem you reported. Basically, the
> > first alarm triggers the IRQ after 1s, as expected, but the next
> > configured alarm 1s into the future never triggers the IRQ again. But
> > the time/date registers seem to be updating (incrementin) correctly
> > after that.
> >
>
> ...and so we agree on what we observe. My guess is that the alarm
> comparator has a latch that triggers only every second update and so you
> need 2 seconds between each alarms.
>
> [...]
>
> > I even did some tests where, in pcf2127_rtc_set_alarm(), I disabled
> > all the alarm registers (set to 0x80), except for the SECONDS alarm
> > register. In this case, I observed that the IRQ is triggered after
> > 61s. This seems to indicate that the alarm detection circuitry is
> > still somewhat operating (AF flag / INT pin), but there is probably a
> > bug in the IC when the configured alarm is close to current time after
> > AF is set once...
> >
> > I also have done other tests by disabling then re-enabling AIE,
> > stopping and restarting the oscillator (STOP bit), etc, but to no
> > avail.
> >
> > However, in pcf2127_rtc_set_alarm(), if I set the alarm 2s past the
> > current time, instead of 1s, then the IRQ is always triggered after
> > 2s.
> >
> > I have opened a support case with NXP to investigate this strange
> > behavior.
>
> Let me know if you ever get a reply.

Hi Alexandre,
after two months and a lot of emails with NXP awful technical support, I was never able to have a valid answer to the problem, apart from "Use a new device as the PCF2127 is not recommended for new designs" :(

On the other hand, have you had time to look at my patch series for the PCF2131 driver?

Thank you, Hugo.


> > > > > Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
> > > > > ---
> > > > > drivers/rtc/rtc-pcf2127.c | 1 +
> > > > > 1 file changed, 1 insertion(+)
> > > > >
> > > > > diff --git a/drivers/rtc/rtc-pcf2127.c b/drivers/rtc/rtc-pcf2127.c
> > > > > index f8469b134411..63b275b014bd 100644
> > > > > --- a/drivers/rtc/rtc-pcf2127.c
> > > > > +++ b/drivers/rtc/rtc-pcf2127.c
> > > > > @@ -656,6 +656,7 @@ static int pcf2127_probe(struct device *dev, struct regmap *regmap,
> > > > > pcf2127->rtc->range_min = RTC_TIMESTAMP_BEGIN_2000;
> > > > > pcf2127->rtc->range_max = RTC_TIMESTAMP_END_2099;
> > > > > pcf2127->rtc->set_start_time = true; /* Sets actual start to 1970 */
> > > > > + set_bit(RTC_FEATURE_ALARM_RES_2S, pcf2127->rtc->features);
> > > > > clear_bit(RTC_FEATURE_UPDATE_INTERRUPT, pcf2127->rtc->features);
> > > > > clear_bit(RTC_FEATURE_ALARM, pcf2127->rtc->features);
> > > > >
> > > > > --
> > > > > 2.35.1
> > > > >
> > > >
> > > >
> > > > --
> > > > Hugo Villeneuve <hugo@hugovil.com>
> > >
> > > --
> > > Alexandre Belloni, co-owner and COO, Bootlin
> > > Embedded Linux and Kernel engineering
> > > https://bootlin.com
> > >
> >
> >
> > --
> > Hugo Villeneuve <hugo@hugovil.com>
>
> --
> Alexandre Belloni, co-owner and COO, Bootlin
> Embedded Linux and Kernel engineering
> https://bootlin.com
>


--
Hugo Villeneuve <hugo@hugovil.com>

\
 
 \ /
  Last update: 2022-05-24 17:48    [W:0.096 / U:1.364 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site