lkml.org 
[lkml]   [2022]   [May]   [18]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v2 5/5] arm64: dts: allwinner: orange-pi-3: Enable ethernet
Date
From: Ondřej Jirman <megi@xff.cz>

Orange Pi 3 has two regulators that power the Realtek RTL8211E
PHY. According to the datasheet, both regulators need to be enabled
at the same time, or that "phy-io" should be enabled slightly earlier
than "phy" regulator.

RTL8211E/RTL8211EG datasheet says:

Note 4: 2.5V (or 1.8/1.5V) RGMII power should be risen simultaneously
or slightly earlier than 3.3V power. Rising 2.5V (or 1.8/1.5V) power
later than 3.3V power may lead to errors.

The timing is set in DT via startup-delay-us.

Signed-off-by: Ondrej Jirman <megi@xff.cz>
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
---
.../dts/allwinner/sun50i-h6-orangepi-3.dts | 38 +++++++++++++++++++
1 file changed, 38 insertions(+)

diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts
index c45d7b7fb39a..c3749b7302ba 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts
@@ -13,6 +13,7 @@ / {
compatible = "xunlong,orangepi-3", "allwinner,sun50i-h6";

aliases {
+ ethernet0 = &emac;
serial0 = &uart0;
serial1 = &uart1;
};
@@ -55,6 +56,15 @@ led-1 {
};
};

+ reg_gmac_2v5: gmac-2v5 {
+ compatible = "regulator-fixed";
+ regulator-name = "gmac-2v5";
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ enable-active-high;
+ gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>; /* PD6 */
+ };
+
reg_vcc5v: vcc5v {
/* board wide 5V supply directly from the DC jack */
compatible = "regulator-fixed";
@@ -113,6 +123,33 @@ &ehci3 {
status = "okay";
};

+&emac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ext_rgmii_pins>;
+ phy-mode = "rgmii-id";
+ phy-handle = <&ext_rgmii_phy>;
+ status = "okay";
+};
+
+&mdio {
+ ext_rgmii_phy: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ /*
+ * The board uses 2.5V RGMII signalling. Power sequence to enable
+ * the phy is to enable GMAC-2V5 and GMAC-3V (aldo2) power rails
+ * at the same time and to wait 100ms. The driver enables phy-io
+ * first. Delay is achieved with enable-ramp-delay on reg_aldo2.
+ */
+ regulators = <&reg_gmac_2v5>, <&reg_aldo2>;
+ regulator-names = "phy-io", "phy";
+
+ reset-gpios = <&pio 3 14 GPIO_ACTIVE_LOW>; /* PD14 */
+ reset-assert-us = <15000>;
+ reset-deassert-us = <40000>;
+ };
+};
+
&gpu {
mali-supply = <&reg_dcdcc>;
status = "okay";
@@ -211,6 +248,7 @@ reg_aldo2: aldo2 {
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-name = "vcc33-audio-tv-ephy-mac";
+ regulator-enable-ramp-delay = <100000>;
};

/* ALDO3 is shorted to CLDO1 */
--
2.35.1
\
 
 \ /
  Last update: 2022-05-18 22:15    [W:0.092 / U:1.032 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site