Messages in this thread | | | Date | Wed, 18 May 2022 10:36:14 -0700 | Subject | Re: [PATCH v2 1/2] phy/qcom: add regulator_set_load to edp/dp phy | From | Kuogee Hsieh <> |
| |
On 5/18/2022 10:12 AM, Dmitry Baryshkov wrote: > On Wed, 18 May 2022 at 19:43, Kuogee Hsieh <quic_khsieh@quicinc.com> wrote: >> This patch add regulator_set_load() to both eDP and DP phy driver >> to have totally control regulators. >> >> Changes in v2: >> -- no regulator_set_laod() before disable regulator >> >> Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> >> --- >> drivers/phy/qualcomm/phy-qcom-edp.c | 25 +++++++++++++++++++++---- >> drivers/phy/qualcomm/phy-qcom-qmp.c | 13 +++++++++++++ > Split into -edp and -qmp part. > >> 2 files changed, 34 insertions(+), 4 deletions(-) >> >> diff --git a/drivers/phy/qualcomm/phy-qcom-edp.c b/drivers/phy/qualcomm/phy-qcom-edp.c >> index cacd32f..9b55095 100644 >> --- a/drivers/phy/qualcomm/phy-qcom-edp.c >> +++ b/drivers/phy/qualcomm/phy-qcom-edp.c >> @@ -87,17 +87,24 @@ struct qcom_edp { >> >> struct clk_bulk_data clks[2]; >> struct regulator_bulk_data supplies[2]; >> + int enable_load[2]; >> + int disable_load[2]; > As noticed in the review of the previous patch, disable_load is unnecessary. > >> }; >> >> static int qcom_edp_phy_init(struct phy *phy) >> { >> struct qcom_edp *edp = phy_get_drvdata(phy); >> int ret; >> + int num_consumers = ARRAY_SIZE(edp->supplies); >> + int i; >> >> - ret = regulator_bulk_enable(ARRAY_SIZE(edp->supplies), edp->supplies); >> + ret = regulator_bulk_enable(num_consumers, edp->supplies); >> if (ret) >> return ret; >> >> + for (i = num_consumers - 1; i >= 0; --i) >> + regulator_set_load(edp->supplies[i].consumer, edp->enable_load[i]); >> + >> ret = clk_bulk_prepare_enable(ARRAY_SIZE(edp->clks), edp->clks); >> if (ret) >> goto out_disable_supplies; >> @@ -425,9 +432,15 @@ static int qcom_edp_phy_power_off(struct phy *phy) >> static int qcom_edp_phy_exit(struct phy *phy) >> { >> struct qcom_edp *edp = phy_get_drvdata(phy); >> + int num_consumers = ARRAY_SIZE(edp->supplies); >> + int i; >> >> clk_bulk_disable_unprepare(ARRAY_SIZE(edp->clks), edp->clks); >> - regulator_bulk_disable(ARRAY_SIZE(edp->supplies), edp->supplies); >> + >> + for (i = num_consumers - 1; i >= 0; --i) >> + regulator_set_load(edp->supplies[i].consumer, edp->disable_load[i]); >> + >> + regulator_bulk_disable(num_consumers, edp->supplies); >> >> return 0; >> } >> @@ -633,8 +646,12 @@ static int qcom_edp_phy_probe(struct platform_device *pdev) >> if (ret) >> return ret; >> >> - edp->supplies[0].supply = "vdda-phy"; >> - edp->supplies[1].supply = "vdda-pll"; >> + edp->supplies[0].supply = "vdda-1p2"; >> + edp->supplies[1].supply = "vdda-0p9"; > NAK, You can not randomly change supply names.
if you do no change here, then we have to change dtsi.
They are not match.
> >> + edp->enable_load[0] = 21800; /* 1.2 V */ >> + edp->enable_load[1] = 36000; /* 1.2 V */ >> + edp->disable_load[0] = 4; /* 0.9 V */ >> + edp->disable_load[1] = 4; /* 10.9V */ > Again, 10.9V here. Kuogee. Have you read the review points? I have read it. but forget to make change at edp file. > >> ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(edp->supplies), edp->supplies); >> if (ret) >> return ret; >> diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.c b/drivers/phy/qualcomm/phy-qcom-qmp.c >> index b144ae1..0a4c8a8 100644 >> --- a/drivers/phy/qualcomm/phy-qcom-qmp.c >> +++ b/drivers/phy/qualcomm/phy-qcom-qmp.c >> @@ -3130,6 +3130,7 @@ struct qmp_phy_cfg { >> int num_resets; >> /* regulators to be requested */ >> const char * const *vreg_list; >> + const unsigned int *vreg_enable_load; >> int num_vregs; >> >> /* array of registers with different offsets */ >> @@ -3346,6 +3347,10 @@ static const char * const qmp_phy_vreg_l[] = { >> "vdda-phy", "vdda-pll", >> }; >> >> +static const unsigned int qmp_phy_vreg_enable_load[] = { >> + 21800, 36000 >> +}; >> + >> static const struct qmp_phy_cfg ipq8074_usb3phy_cfg = { >> .type = PHY_TYPE_USB3, >> .nlanes = 1, >> @@ -4072,6 +4077,7 @@ static const struct qmp_phy_cfg sm8250_usb3phy_cfg = { >> .reset_list = msm8996_usb3phy_reset_l, >> .num_resets = ARRAY_SIZE(msm8996_usb3phy_reset_l), >> .vreg_list = qmp_phy_vreg_l, >> + .vreg_enable_load = qmp_phy_vreg_enable_load, >> .num_vregs = ARRAY_SIZE(qmp_phy_vreg_l), >> .regs = qmp_v4_usb3phy_regs_layout, >> >> @@ -4139,6 +4145,7 @@ static const struct qmp_phy_cfg sm8250_dpphy_cfg = { >> .reset_list = msm8996_usb3phy_reset_l, >> .num_resets = ARRAY_SIZE(msm8996_usb3phy_reset_l), >> .vreg_list = qmp_phy_vreg_l, >> + .vreg_enable_load = qmp_phy_vreg_enable_load, >> .num_vregs = ARRAY_SIZE(qmp_phy_vreg_l), >> .regs = qmp_v4_usb3phy_regs_layout, >> >> @@ -5008,6 +5015,11 @@ static int qcom_qmp_phy_com_init(struct qmp_phy *qphy) >> return 0; >> } >> >> + if (cfg->vreg_enable_load) { >> + for (i = cfg->num_vregs - 1; i >= 0; --i) > What's the point of iterating the list backwards?
do no know,
I just follow the order from regulator_bulk_enable()
> >> + regulator_set_load(qmp->vregs[i].consumer, cfg->vreg_enable_load[i]); >> + } >> + >> /* turn on regulator supplies */ >> ret = regulator_bulk_enable(cfg->num_vregs, qmp->vregs); >> if (ret) { >> @@ -5116,6 +5128,7 @@ static int qcom_qmp_phy_com_exit(struct qmp_phy *qphy) >> >> clk_bulk_disable_unprepare(cfg->num_clks, qmp->clks); >> >> + /* no minimum load set required before disable regulator */ > No otneed for the comment. > >> regulator_bulk_disable(cfg->num_vregs, qmp->vregs); >> >> mutex_unlock(&qmp->phy_mutex); >> -- >> The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, >> a Linux Foundation Collaborative Project >> >
| |