lkml.org 
[lkml]   [2022]   [May]   [17]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v5 10/10] i2c: npcm: Capitalize the one-line comment
Date
From: Tyrone Ting <kfting@nuvoton.com>

Make the one-line comments capital in the driver to get the comment style
consistent.

Fixes: 56a1485b102e ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver")
Signed-off-by: Tyrone Ting <kfting@nuvoton.com>
---
drivers/i2c/busses/i2c-npcm7xx.c | 12 ++++++------
1 file changed, 6 insertions(+), 6 deletions(-)

diff --git a/drivers/i2c/busses/i2c-npcm7xx.c b/drivers/i2c/busses/i2c-npcm7xx.c
index a032b407f104..a60e392dda50 100644
--- a/drivers/i2c/busses/i2c-npcm7xx.c
+++ b/drivers/i2c/busses/i2c-npcm7xx.c
@@ -683,7 +683,7 @@ static void npcm_i2c_reset(struct npcm_i2c *bus)
}
#endif

- /* clear status bits for spurious interrupts */
+ /* Clear status bits for spurious interrupts */
npcm_i2c_clear_master_status(bus);

bus->state = I2C_IDLE;
@@ -1255,7 +1255,7 @@ static irqreturn_t npcm_i2c_int_slave_handler(struct npcm_i2c *bus)
} /* SDAST */

/*
- * if irq is not one of the above, make sure EOB is disabled and all
+ * If irq is not one of the above, make sure EOB is disabled and all
* status bits are cleared.
*/
if (ret == IRQ_NONE) {
@@ -1509,7 +1509,7 @@ static void npcm_i2c_irq_handle_nack(struct npcm_i2c *bus)
npcm_i2c_clear_master_status(bus);
readx_poll_timeout_atomic(ioread8, bus->reg + NPCM_I2CCST, val,
!(val & NPCM_I2CCST_BUSY), 10, 200);
- /* verify no status bits are still set after bus is released */
+ /* Verify no status bits are still set after bus is released */
npcm_i2c_clear_master_status(bus);
}
bus->state = I2C_IDLE;
@@ -1977,7 +1977,7 @@ static int npcm_i2c_init_module(struct npcm_i2c *bus, enum i2c_mode mode,

npcm_i2c_reset(bus);

- /* check HW is OK: SDA and SCL should be high at this point. */
+ /* Check HW is OK: SDA and SCL should be high at this point. */
if ((npcm_i2c_get_SDA(&bus->adap) == 0) || (npcm_i2c_get_SCL(&bus->adap) == 0)) {
dev_err(bus->dev, "I2C%d init fail: lines are low\n", bus->num);
dev_err(bus->dev, "SDA=%d SCL=%d\n", npcm_i2c_get_SDA(&bus->adap),
@@ -2037,7 +2037,7 @@ static irqreturn_t npcm_i2c_bus_irq(int irq, void *dev_id)
return IRQ_HANDLED;
}
#endif
- /* clear status bits for spurious interrupts */
+ /* Clear status bits for spurious interrupts */
npcm_i2c_clear_master_status(bus);

return IRQ_HANDLED;
@@ -2219,7 +2219,7 @@ static int npcm_i2c_master_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs,
(bus->data->rxf_ctl_last_pec & ioread8(bus->reg + NPCM_I2CRXF_CTL)))
npcm_i2c_reset(bus);

- /* after any xfer, successful or not, stall and EOB must be disabled */
+ /* After any xfer, successful or not, stall and EOB must be disabled */
npcm_i2c_stall_after_start(bus, false);
npcm_i2c_eob_int(bus, false);

--
2.17.1
\
 
 \ /
  Last update: 2022-05-17 12:16    [W:0.349 / U:0.152 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site