lkml.org 
[lkml]   [2022]   [May]   [16]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v2 01/24] ARM: dts: imx7-colibri: overhaul display/touch functionality
Date
From: Marcel Ziswiler <marcel.ziswiler@toradex.com>

Rename display interface to match other modules to make it easier to
use device tree overlays.

The parallel RGB interface (lcdif) and all related stuff turn on in a
device tree overlay. Keep them disabled in the main devicetree.
As these subsystems are provided by module and not a part of boards,
move their definitions into the module-level devicetree.

Disable ad7879 touchscreen which turns on in a devic tree overlay.
Remains it disabled in the main devicetree.

Move Atmel MXT capacitive touch controller device tree nodes from
carrier board to module level and add iomux pinctl groups for both the
Capacitive Touch Adapter (using SODIMM 28/30) and the capacitive touch
connector as found on later carrier boards (using SODIMM 106/107).

Keep touchscreen and display nodes enabled for NAND based i.MX 7
modules, since device tree overlays are not yet supported. For the
Colibri Evaluation Board keep the Capacitive Touch Adapter node
disabled and PWM2, PWM3 enabled instead.

For eMMC based modules keep nodes disabled to work in conjunction with
device tree overlays.

Add the iomuxc pinctrl group for the LVDS transceiver related signals to
use it in a device tree overlay.

While at it also alphabetically re=order them properties.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
---

(no changes since v1)

arch/arm/boot/dts/imx7-colibri-aster.dtsi | 53 ------------
arch/arm/boot/dts/imx7-colibri-eval-v3.dtsi | 66 +++-----------
arch/arm/boot/dts/imx7-colibri.dtsi | 95 ++++++++++++++++++---
arch/arm/boot/dts/imx7d-colibri-aster.dts | 20 +++++
arch/arm/boot/dts/imx7d-colibri-eval-v3.dts | 32 +++++++
arch/arm/boot/dts/imx7s-colibri-aster.dts | 20 +++++
arch/arm/boot/dts/imx7s-colibri-eval-v3.dts | 32 +++++++
7 files changed, 197 insertions(+), 121 deletions(-)

diff --git a/arch/arm/boot/dts/imx7-colibri-aster.dtsi b/arch/arm/boot/dts/imx7-colibri-aster.dtsi
index b770fc937970..950b4e5f6cf4 100644
--- a/arch/arm/boot/dts/imx7-colibri-aster.dtsi
+++ b/arch/arm/boot/dts/imx7-colibri-aster.dtsi
@@ -4,10 +4,6 @@
*
*/

-
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/pwm/pwm.h>
-
/ {
chosen {
stdout-path = "serial0:115200n8";
@@ -27,18 +23,6 @@ power {
};
};

- panel: panel {
- compatible = "edt,et057090dhu";
- backlight = <&bl>;
- power-supply = <&reg_3v3>;
-
- port {
- panel_in: endpoint {
- remote-endpoint = <&lcdif_out>;
- };
- };
- };
-
reg_3v3: regulator-3v3 {
compatible = "regulator-fixed";
regulator-name = "3.3V";
@@ -77,13 +61,6 @@ &adc2 {
status = "disabled";
};

-&bl {
- brightness-levels = <0 4 8 16 32 64 128 255>;
- default-brightness-level = <6>;
- power-supply = <&reg_3v3>;
- status = "okay";
-};
-
&fec1 {
status = "okay";
};
@@ -91,17 +68,6 @@ &fec1 {
&i2c4 {
status = "okay";

- /* Microchip/Atmel maxtouch controller */
- touchscreen@4a {
- compatible = "atmel,maxtouch";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_gpiotouch>;
- reg = <0x4a>;
- interrupt-parent = <&gpio2>;
- interrupts = <15 IRQ_TYPE_EDGE_FALLING>; /* SODIMM 107 */
- reset-gpios = <&gpio2 28 GPIO_ACTIVE_LOW>; /* SODIMM 106 */
- };
-
/* M41T0M6 real time clock on carrier board */
rtc: rtc@68 {
compatible = "st,m41t0";
@@ -109,25 +75,6 @@ rtc: rtc@68 {
};
};

-&iomuxc {
- pinctrl_gpiotouch: touchgpios {
- fsl,pins = <
- MX7D_PAD_EPDC_DATA15__GPIO2_IO15 0x74
- MX7D_PAD_EPDC_BDR0__GPIO2_IO28 0x14
- >;
- };
-};
-
-&lcdif {
- status = "okay";
-
- port {
- lcdif_out: endpoint {
- remote-endpoint = <&panel_in>;
- };
- };
-};
-
&pwm1 {
status = "okay";
};
diff --git a/arch/arm/boot/dts/imx7-colibri-eval-v3.dtsi b/arch/arm/boot/dts/imx7-colibri-eval-v3.dtsi
index 3b9df8c82ae3..d6fa74222960 100644
--- a/arch/arm/boot/dts/imx7-colibri-eval-v3.dtsi
+++ b/arch/arm/boot/dts/imx7-colibri-eval-v3.dtsi
@@ -34,18 +34,6 @@ power {
};
};

- panel: panel {
- compatible = "edt,et057090dhu";
- backlight = <&bl>;
- power-supply = <&reg_3v3>;
-
- port {
- panel_in: endpoint {
- remote-endpoint = <&lcdif_out>;
- };
- };
- };
-
reg_3v3: regulator-3v3 {
compatible = "regulator-fixed";
regulator-name = "3.3V";
@@ -72,14 +60,6 @@ reg_usbh_vbus: regulator-usbh-vbus {
};
};

-&bl {
- brightness-levels = <0 4 8 16 32 64 128 255>;
- default-brightness-level = <6>;
- power-supply = <&reg_3v3>;
-
- status = "okay";
-};
-
&adc1 {
status = "okay";
};
@@ -88,6 +68,18 @@ &adc2 {
status = "okay";
};

+/*
+ * The Atmel maxtouch controller uses SODIMM 28/30, also used for PWM<B>, PWM<C>, aka pwm2, pwm3.
+ * So if you enable following capacitive touch controller, disable pwm2/pwm3 first.
+ */
+&atmel_mxt_ts {
+ interrupt-parent = <&gpio1>;
+ interrupts = <9 IRQ_TYPE_EDGE_FALLING>; /* SODIMM 28 / INT */
+ pinctrl-0 = <&pinctrl_atmel_adapter>;
+ reset-gpios = <&gpio1 10 GPIO_ACTIVE_LOW>; /* SODIMM 30 / RST */
+ status = "disabled";
+};
+
&ecspi3 {
status = "okay";

@@ -113,21 +105,6 @@ &fec1 {
&i2c4 {
status = "okay";

- /*
- * Touchscreen is using SODIMM 28/30, also used for PWM<B>, PWM<C>,
- * aka pwm2, pwm3. so if you enable touchscreen, disable the pwms
- */
- touchscreen@4a {
- compatible = "atmel,maxtouch";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_gpiotouch>;
- reg = <0x4a>;
- interrupt-parent = <&gpio1>;
- interrupts = <9 IRQ_TYPE_EDGE_FALLING>; /* SODIMM 28 */
- reset-gpios = <&gpio1 10 GPIO_ACTIVE_LOW>; /* SODIMM 30 */
- status = "disabled";
- };
-
/* M41T0M6 real time clock on carrier board */
rtc: rtc@68 {
compatible = "st,m41t0";
@@ -135,16 +112,6 @@ rtc: rtc@68 {
};
};

-&lcdif {
- status = "okay";
-
- port {
- lcdif_out: endpoint {
- remote-endpoint = <&panel_in>;
- };
- };
-};
-
&pwm1 {
status = "okay";
};
@@ -183,12 +150,3 @@ &usdhc1 {
vmmc-supply = <&reg_3v3>;
status = "okay";
};
-
-&iomuxc {
- pinctrl_gpiotouch: touchgpios {
- fsl,pins = <
- MX7D_PAD_GPIO1_IO09__GPIO1_IO9 0x74
- MX7D_PAD_GPIO1_IO10__GPIO1_IO10 0x14
- >;
- };
-};
diff --git a/arch/arm/boot/dts/imx7-colibri.dtsi b/arch/arm/boot/dts/imx7-colibri.dtsi
index f1c60b0cb143..e20b0977f38f 100644
--- a/arch/arm/boot/dts/imx7-colibri.dtsi
+++ b/arch/arm/boot/dts/imx7-colibri.dtsi
@@ -3,13 +3,32 @@
* Copyright 2016-2020 Toradex
*/

+#include <dt-bindings/pwm/pwm.h>
+
/ {
- bl: backlight {
+ backlight: backlight {
+ brightness-levels = <0 45 63 88 119 158 203 255>;
compatible = "pwm-backlight";
+ default-brightness-level = <4>;
+ enable-gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_gpio_bl_on>;
- pwms = <&pwm1 0 5000000 0>;
- enable-gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
+ power-supply = <&reg_module_3v3>;
+ pwms = <&pwm1 0 6666667 PWM_POLARITY_INVERTED>;
+ status = "disabled";
+ };
+
+ panel_dpi: panel-dpi {
+ backlight = <&backlight>;
+ compatible = "edt,et057090dhu";
+ power-supply = <&reg_3v3>;
+ status = "disabled";
+
+ port {
+ lcd_panel_in: endpoint {
+ remote-endpoint = <&lcdif_out>;
+ };
+ };
};

reg_module_3v3: regulator-module-3v3 {
@@ -301,18 +320,19 @@ codec: sgtl5000@a {
VDDD-supply = <&reg_DCDC3>;
};

- ad7879@2c {
+ ad7879_ts: touchscreen@2c {
+ adi,acquisition-time = /bits/ 8 <1>;
+ adi,averaging = /bits/ 8 <1>;
+ adi,conversion-interval = /bits/ 8 <255>;
+ adi,first-conversion-delay = /bits/ 8 <3>;
+ adi,median-filter-size = /bits/ 8 <2>;
+ adi,resistance-plate-x = <120>;
compatible = "adi,ad7879-1";
- reg = <0x2c>;
interrupt-parent = <&gpio1>;
interrupts = <13 IRQ_TYPE_EDGE_FALLING>;
+ reg = <0x2c>;
touchscreen-max-pressure = <4096>;
- adi,resistance-plate-x = <120>;
- adi,first-conversion-delay = /bits/ 8 <3>;
- adi,acquisition-time = /bits/ 8 <1>;
- adi,median-filter-size = /bits/ 8 <2>;
- adi,averaging = /bits/ 8 <1>;
- adi,conversion-interval = /bits/ 8 <255>;
+ status = "disabled";
};

pmic@33 {
@@ -392,12 +412,32 @@ &i2c4 {
pinctrl-1 = <&pinctrl_i2c4_recovery>;
scl-gpios = <&gpio7 8 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
sda-gpios = <&gpio7 9 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ status = "disabled";
+
+ /* Atmel maxtouch controller */
+ atmel_mxt_ts: touchscreen@4a {
+ compatible = "atmel,maxtouch";
+ interrupt-parent = <&gpio2>;
+ interrupts = <15 IRQ_TYPE_EDGE_FALLING>; /* SODIMM 107 / INT */
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_atmel_connector>;
+ reg = <0x4a>;
+ reset-gpios = <&gpio2 28 GPIO_ACTIVE_LOW>; /* SODIMM 106 / RST */
+ status = "disabled";
+ };
};

&lcdif {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_lcdif_dat
&pinctrl_lcdif_ctrl>;
+ status = "disabled";
+
+ port {
+ lcdif_out: endpoint {
+ remote-endpoint = <&lcd_panel_in>;
+ };
+ };
};

&pwm1 {
@@ -486,7 +526,27 @@ &usdhc3 {
&iomuxc {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_gpio1 &pinctrl_gpio2 &pinctrl_gpio3 &pinctrl_gpio4
- &pinctrl_gpio7 &pinctrl_usbc_det>;
+ &pinctrl_usbc_det>;
+
+ /*
+ * Atmel MXT touchsceen + Capacitive Touch Adapter
+ * NOTE: This pin group conflicts with pin groups pinctrl_pwm2/pinctrl_pwm3.
+ * Don't use them simultaneously.
+ */
+ pinctrl_atmel_adapter: atmelconnectorgrp {
+ fsl,pins = <
+ MX7D_PAD_GPIO1_IO09__GPIO1_IO9 0x74 /* SODIMM 28 / INT */
+ MX7D_PAD_GPIO1_IO10__GPIO1_IO10 0x14 /* SODIMM 30 / RST */
+ >;
+ };
+
+ /* Atmel MXT touchsceen + boards with built-in Capacitive Touch Connector */
+ pinctrl_atmel_connector: atmeladaptergrp {
+ fsl,pins = <
+ MX7D_PAD_EPDC_BDR0__GPIO2_IO28 0x14 /* SODIMM 106 / RST */
+ MX7D_PAD_EPDC_DATA15__GPIO2_IO15 0x74 /* SODIMM 107 / INT */
+ >;
+ };

pinctrl_gpio1: gpio1-grp {
fsl,pins = <
@@ -494,8 +554,6 @@ MX7D_PAD_SAI1_RX_SYNC__GPIO6_IO16 0x14 /* SODIMM 77 */
MX7D_PAD_EPDC_DATA09__GPIO2_IO9 0x14 /* SODIMM 89 */
MX7D_PAD_EPDC_DATA08__GPIO2_IO8 0x74 /* SODIMM 91 */
MX7D_PAD_LCD_RESET__GPIO3_IO4 0x14 /* SODIMM 93 */
- MX7D_PAD_EPDC_DATA13__GPIO2_IO13 0x14 /* SODIMM 95 */
- MX7D_PAD_ENET1_RGMII_TXC__GPIO7_IO11 0x14 /* SODIMM 99 */
MX7D_PAD_EPDC_DATA10__GPIO2_IO10 0x74 /* SODIMM 105 */
MX7D_PAD_EPDC_DATA00__GPIO2_IO0 0x14 /* SODIMM 111 */
MX7D_PAD_EPDC_DATA01__GPIO2_IO1 0x14 /* SODIMM 113 */
@@ -729,6 +787,15 @@ MX7D_PAD_LCD_HSYNC__LCD_HSYNC 0x79
>;
};

+ pinctrl_lvds_transceiver: lvdstx {
+ fsl,pins = <
+ MX7D_PAD_ENET1_RGMII_RD2__GPIO7_IO2 0x14 /* SODIMM 63 */
+ MX7D_PAD_ENET1_RGMII_RD3__GPIO7_IO3 0x74 /* SODIMM 55 */
+ MX7D_PAD_ENET1_RGMII_TXC__GPIO7_IO11 0x14 /* SODIMM 99 */
+ MX7D_PAD_EPDC_DATA13__GPIO2_IO13 0x14 /* SODIMM 95 */
+ >;
+ };
+
pinctrl_pwm1: pwm1-grp {
fsl,pins = <
MX7D_PAD_GPIO1_IO08__PWM1_OUT 0x79
diff --git a/arch/arm/boot/dts/imx7d-colibri-aster.dts b/arch/arm/boot/dts/imx7d-colibri-aster.dts
index f3f0537d5a37..ce0e6bb7db37 100644
--- a/arch/arm/boot/dts/imx7d-colibri-aster.dts
+++ b/arch/arm/boot/dts/imx7d-colibri-aster.dts
@@ -14,6 +14,26 @@ / {
"fsl,imx7d";
};

+&ad7879_ts {
+ status = "okay";
+};
+
+&atmel_mxt_ts {
+ status = "okay";
+};
+
+&backlight {
+ status = "okay";
+};
+
+&lcdif {
+ status = "okay";
+};
+
+&panel_dpi {
+ status = "okay";
+};
+
&usbotg2 {
vbus-supply = <&reg_usbh_vbus>;
status = "okay";
diff --git a/arch/arm/boot/dts/imx7d-colibri-eval-v3.dts b/arch/arm/boot/dts/imx7d-colibri-eval-v3.dts
index 87b132bcd272..c610c50c003a 100644
--- a/arch/arm/boot/dts/imx7d-colibri-eval-v3.dts
+++ b/arch/arm/boot/dts/imx7d-colibri-eval-v3.dts
@@ -13,6 +13,38 @@ / {
"fsl,imx7d";
};

+&ad7879_ts {
+ status = "okay";
+};
+
+/*
+ * The Atmel maxtouch controller uses SODIMM 28/30, also used for PWM<B>, PWM<C>, aka pwm2, pwm3.
+ * So if you enable following capacitive touch controller, disable pwm2/pwm3 first.
+ */
+&atmel_mxt_ts {
+ status = "disabled";
+};
+
+&backlight {
+ status = "okay";
+};
+
+&lcdif {
+ status = "okay";
+};
+
+&panel_dpi {
+ status = "okay";
+};
+
+&pwm2 {
+ status = "okay";
+};
+
+&pwm3 {
+ status = "okay";
+};
+
&usbotg2 {
vbus-supply = <&reg_usbh_vbus>;
status = "okay";
diff --git a/arch/arm/boot/dts/imx7s-colibri-aster.dts b/arch/arm/boot/dts/imx7s-colibri-aster.dts
index fca4e0a95c1b..87f9e0e079a8 100644
--- a/arch/arm/boot/dts/imx7s-colibri-aster.dts
+++ b/arch/arm/boot/dts/imx7s-colibri-aster.dts
@@ -13,3 +13,23 @@ / {
compatible = "toradex,colibri-imx7s-aster", "toradex,colibri-imx7s",
"fsl,imx7s";
};
+
+&ad7879_ts {
+ status = "okay";
+};
+
+&atmel_mxt_ts {
+ status = "okay";
+};
+
+&backlight {
+ status = "okay";
+};
+
+&lcdif {
+ status = "okay";
+};
+
+&panel_dpi {
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx7s-colibri-eval-v3.dts b/arch/arm/boot/dts/imx7s-colibri-eval-v3.dts
index aa70d3f2e2e2..81956c16b95b 100644
--- a/arch/arm/boot/dts/imx7s-colibri-eval-v3.dts
+++ b/arch/arm/boot/dts/imx7s-colibri-eval-v3.dts
@@ -12,3 +12,35 @@ / {
compatible = "toradex,colibri-imx7s-eval-v3", "toradex,colibri-imx7s",
"fsl,imx7s";
};
+
+&ad7879_ts {
+ status = "okay";
+};
+
+/*
+ * The Atmel maxtouch controller uses SODIMM 28/30, also used for PWM<B>, PWM<C>, aka pwm2, pwm3.
+ * So if you enable following capacitive touch controller, disable pwm2/pwm3 first.
+ */
+&atmel_mxt_ts {
+ status = "disabled";
+};
+
+&backlight {
+ status = "okay";
+};
+
+&lcdif {
+ status = "okay";
+};
+
+&panel_dpi {
+ status = "okay";
+};
+
+&pwm2 {
+ status = "okay";
+};
+
+&pwm3 {
+ status = "okay";
+};
--
2.35.1
\
 
 \ /
  Last update: 2022-05-16 15:49    [W:0.169 / U:0.288 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site