lkml.org 
[lkml]   [2022]   [May]   [16]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
SubjectRe: [PATCH] USB: serial: option: add Quectel BG95 modem
On Mon, May 16, 2022 at 06:10:17AM +0000, Carl Yin(殷张成) wrote:
> The BG95 modem has 2 USB configurations that are configurable via the AT
> command AT+QCFGEXT="usbnet",["ecm"|"modem"] which make the modem enumerate
> with the following interfaces, respectively:
>
> "modem": Diag + GNSS + Modem + Modem
> "ecm" : DIAG + GNSS + Modem + ECM

Hi Carl,

what about the AT+QCFGEXT="usbnet","rmnet" configuration available on
several firmware versions which makes the BG95 enumerate as
Diag + GNSS + Modem + QMI:

T: Bus=02 Lev=02 Prnt=06 Port=01 Cnt=02 Dev#= 8 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=2c7c ProdID=0700 Rev= 0.00
S: Manufacturer=Quectel, Incorporated
S: Product=Quectel LPWA Module
S: SerialNumber=xxxxxxxx
C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E: Ad=85(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms

>
> A detailed description of the USB configuration for each mode follows:
>
> +QCFGEXT: "usbnet","modem"
> -------------------------
> T: Bus=01 Lev=02 Prnt=02 Port=01 Cnt=01 Dev#= 3 Spd=480 MxCh= 0
> D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
> P: Vendor=2c7c ProdID=0700 Rev= 0.00
> S: Manufacturer=Quectel, Incorporated
> S: Product=Quectel LPWA Module
> S: SerialNumber=884328a2
> C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=500mA
> I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
> E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fe Prot=ff Driver=option
> E: Ad=85(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
> E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>
> +QCFGEXT: "usbnet","ecm"
> -----------------------
> T: Bus=01 Lev=02 Prnt=02 Port=01 Cnt=01 Dev#= 4 Spd=480 MxCh= 0
> D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
> P: Vendor=2c7c ProdID=0700 Rev= 0.00
> S: Manufacturer=Quectel, Incorporated
> S: Product=Quectel LPWA Module
> S: SerialNumber=884328a2
> C:* #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
> A: FirstIf#= 3 IfCount= 2 Cls=02(comm.) Sub=00 Prot=00
> I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
> E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 3 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=00 Driver=cdc_ether
> E: Ad=85(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
> I: If#= 4 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
> I:* If#= 4 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
> E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>
> Signed-off-by: Carl Yin <carl.yin@quectel.com>
> ---
> drivers/usb/serial/option.c | 5 +++++
> 1 file changed, 5 insertions(+)
>
> diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c
> index 152ad8826..f91b2a67d 100644
> --- a/drivers/usb/serial/option.c
> +++ b/drivers/usb/serial/option.c
> @@ -256,6 +256,7 @@ static void option_instat_callback(struct urb *urb);
> #define QUECTEL_PRODUCT_RM500Q 0x0800
> #define QUECTEL_PRODUCT_EC200S_CN 0x6002
> #define QUECTEL_PRODUCT_EC200T 0x6026
> +#define QUECTEL_PRODUCT_BG95 0x0700
>
> #define CMOTECH_VENDOR_ID 0x16d8
> #define CMOTECH_PRODUCT_6001 0x6001
> @@ -1143,6 +1144,10 @@ static const struct usb_device_id option_ids[] = {
> .driver_info = ZLP },
> { USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EC200S_CN, 0xff, 0, 0) },
> { USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EC200T, 0xff, 0, 0) },
> + { USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_BG95, 0xff, 0xff, 0xff),
> + .driver_info = ZLP },

Could you please add a RSVD(3) flag to the driver_info here to avoid
that the option driver incorrectly binds to the QMI interface?

Regards,
Reinhard

> + { USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_BG95, 0xff, 0xfe, 0xff),
> + .driver_info = ZLP },
>
> { USB_DEVICE(CMOTECH_VENDOR_ID, CMOTECH_PRODUCT_6001) },
> { USB_DEVICE(CMOTECH_VENDOR_ID, CMOTECH_PRODUCT_CMU_300) },
> --
> 2.17.1
>

\
 
 \ /
  Last update: 2022-05-16 23:22    [W:0.055 / U:0.560 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site