lkml.org 
[lkml]   [2022]   [May]   [14]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
SubjectRe: [PATCH V2 1/6] iio: accel: bmi088: Modified the scale calculate
On Tue, 10 May 2022 14:17:48 +0000
LI Qingwu <Qing-wu.Li@leica-geosystems.com.cn> wrote:

> The units after application of scale are 100*m/s^2,
> The scale calculation is only for the device
> with the range of 3, 6, 12, and 24g,
> but some other chips have a range of 2, 4, 6, and 8g.
>
> Modified the formula to a scale list.
> The scales in the list are calculated by 1/sensitivity*9.8.
> The new units after the application of scale are m/s^2.
>
> Signed-off-by: LI Qingwu <Qing-wu.Li@leica-geosystems.com.cn>
> ---
> drivers/iio/accel/bmi088-accel-core.c | 12 +++++++-----
> 1 file changed, 7 insertions(+), 5 deletions(-)
>
> diff --git a/drivers/iio/accel/bmi088-accel-core.c b/drivers/iio/accel/bmi088-accel-core.c
> index a06dae5c971d..9300313b63cb 100644
> --- a/drivers/iio/accel/bmi088-accel-core.c
> +++ b/drivers/iio/accel/bmi088-accel-core.c
> @@ -119,6 +119,7 @@ struct bmi088_accel_chip_info {
> u8 chip_id;
> const struct iio_chan_spec *channels;
> int num_channels;
> + const int scale_table[4][2];
> };
>
> struct bmi088_accel_data {
> @@ -280,6 +281,7 @@ static int bmi088_accel_read_raw(struct iio_dev *indio_dev,
> struct bmi088_accel_data *data = iio_priv(indio_dev);
> struct device *dev = regmap_get_device(data->regmap);
> int ret;
> + int reg;
>
> switch (mask) {
> case IIO_CHAN_INFO_RAW:
> @@ -330,13 +332,12 @@ static int bmi088_accel_read_raw(struct iio_dev *indio_dev,
> return ret;
>
> ret = regmap_read(data->regmap,
> - BMI088_ACCEL_REG_ACC_RANGE, val);
> + BMI088_ACCEL_REG_ACC_RANGE, &reg);
> if (ret)
> goto out_read_raw_pm_put;
> -
> - *val2 = 15 - (*val & 0x3);
> - *val = 3 * 980;
> - ret = IIO_VAL_FRACTIONAL_LOG2;
> + *val = data->chip_info->scale_table[reg&0x03][0];
> + *val2 = data->chip_info->scale_table[reg&0x03][1];

Spaces needed around the &
The 0x03 should be a define - something like BMIO088_ACCEL_ACC_RANGE_MSK

Also, this driver doesn't yet use FIELD_PREP() / FIELD_GET()
but this is a good example of where using FIELD_GET() will make the logic
clearer.


> + ret = IIO_VAL_INT_PLUS_MICRO;
>
> goto out_read_raw_pm_put;
> default:
> @@ -432,6 +433,7 @@ static const struct bmi088_accel_chip_info bmi088_accel_chip_info_tbl[] = {
> .chip_id = 0x1E,
> .channels = bmi088_accel_channels,
> .num_channels = ARRAY_SIZE(bmi088_accel_channels),
> + .scale_table = {{0, 897}, {0, 1795}, {0, 3590}, {0, 7179}},
> },
> };
>

\
 
 \ /
  Last update: 2022-05-14 17:25    [W:0.227 / U:0.060 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site