lkml.org 
[lkml]   [2022]   [May]   [13]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH] ASoC: max98088: add support for reg_4a_cfg_bypass reg
On Thu, May 12, 2022 at 12:19:03PM +0100, Mark Brown wrote:
> On Thu, May 12, 2022 at 01:09:59PM +0200, Tommaso Merciai wrote:
> > On Thu, May 12, 2022 at 11:53:07AM +0100, Mark Brown wrote:
> > > On Thu, May 12, 2022 at 12:46:42PM +0200, Tommaso Merciai wrote:
> > > > On Thu, May 12, 2022 at 11:12:02AM +0100, Mark Brown wrote:
>
> > > > > These look like they should be DAPM controls since they're controlling
> > > > > audio routing but they're being added as regular controls.
>
> > > > Sorry again. You suggest to create a new structure for these entries,
> > > > for example:
>
> > > If that's how they fit into the routing for the device, yes - you'd need
> > > to define the bypass mixer as well and set up appropraite routes.
>
> > I added this reg as regular controls because this reg is pretty generic
> > as you can see this controll bypass of some output, not all.
> > What do you think about?
>
> That sounds exactly like a DAPM control, please make them DAPM controls.

Hi Mark,
Sorry again, but I'm quite new on alsa subsystem. I need an help on figuring out
on how to implements your solution. From what you suggest I got that I need to create
a bypass mixer for every switch (4 -> SPK, REC, MIC2, INA):

/* Out Mixer SPK */
static const struct snd_kcontrol_new max98088_output_bypass_spk_mixer_controls[] = {
SOC_DAPM_SINGLE("SPK Bypass Switch", M98088_REG_4A_CFG_BYPASS, 0, 1, 0),
};

/* Out Mixer REC */
static const struct snd_kcontrol_new max98088_output_bypass_rec_mixer_controls[] = {
SOC_DAPM_SINGLE("REC Bypass Switch", M98088_REG_4A_CFG_BYPASS, 1, 1, 0),
};

/* Out Mixer MIC */
static const struct snd_kcontrol_new max98088_output_bypass_mic_mixer_controls[] = {
SOC_DAPM_SINGLE("MIC2 Bypass Switch", M98088_REG_4A_CFG_BYPASS, 4, 1, 0),
};

/* Out Mixer INA */
static const struct snd_kcontrol_new max98088_output_bypass_ina_mixer_controls[] = {
SOC_DAPM_SINGLE("INA Bypass Switch", M98088_REG_4A_CFG_BYPASS, 7, 1, 0),
};

After that, I need to route the new control mixers on the switch:

{"Out Mixer SPK", "SPK Bypass Switch", "RECN"},
{"Out Mixer REC", "REC Bypass Switch", "RECP"},
{"Out Mixer MIC", "MIC2 Bypass Switch", "MIC1"},
{"Out Mixer INA", "INA Bypass Switch", "INA"},

Then route the bypass switch to the new output:

{"SPKL", NULL, "SPK Bypass Switch"},
{"RECN", NULL, "REC Bypass Switch"},
{"MIC2", NULL, "MIC2 Bypass Switch"},
{"MIC1", NULL, "INA Bypass Switch"},

I'm in the right way? What do you think about?
Can you point me a similar bypass switch into the kernel to take as reference?
Thanks in advance

Regards,
Tommmaso




--
Tommaso Merciai
Embedded Linux Engineer
tommaso.merciai@amarulasolutions.com
__________________________________

Amarula Solutions SRL
Via Le Canevare 30, 31100 Treviso, Veneto, IT
T. +39 042 243 5310
info@amarulasolutions.com
www.amarulasolutions.com

\
 
 \ /
  Last update: 2022-05-13 17:22    [W:0.291 / U:0.100 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site