lkml.org 
[lkml]   [2022]   [May]   [13]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH v3 5/5] pinctrl: renesas: pinctrl-rzg2l: Add IRQ domain to handle GPIO interrupt
On Fri, May 13, 2022 at 7:12 AM Biju Das <biju.das.jz@bp.renesas.com> wrote:
>
>
>
> > -----Original Message-----
> > From: Biju Das
> > Sent: 12 May 2022 18:59
> > To: Lad, Prabhakar <prabhakar.csengg@gmail.com>
> > Cc: Prabhakar Mahadev Lad <prabhakar.mahadev-lad.rj@bp.renesas.com>; Geert
> > Uytterhoeven <geert+renesas@glider.be>; Linus Walleij
> > <linus.walleij@linaro.org>; Thomas Gleixner <tglx@linutronix.de>; Marc
> > Zyngier <maz@kernel.org>; Rob Herring <robh+dt@kernel.org>; Krzysztof
> > Kozlowski <krzysztof.kozlowski+dt@linaro.org>; Bartosz Golaszewski
> > <brgl@bgdev.pl>; Philipp Zabel <p.zabel@pengutronix.de>; linux-
> > gpio@vger.kernel.org; linux-kernel@vger.kernel.org; linux-renesas-
> > soc@vger.kernel.org; devicetree@vger.kernel.org; Phil Edworthy
> > <phil.edworthy@renesas.com>
> > Subject: RE: [PATCH v3 5/5] pinctrl: renesas: pinctrl-rzg2l: Add IRQ domain
> > to handle GPIO interrupt
> >
> > Hi Prabhakar,
> >
> > > Subject: Re: [PATCH v3 5/5] pinctrl: renesas: pinctrl-rzg2l: Add IRQ
> > > domain to handle GPIO interrupt
> > >
> > > Hi Biju,
> > >
> > > Thank you for the review.
> > >
> > > On Thu, May 12, 2022 at 6:35 AM Biju Das <biju.das.jz@bp.renesas.com>
> > > wrote:
> > > >
> > > > Hi Prabhakar,
> > > >
> > > > Thanks for the patch.
> > > >
> > > > > Prabhakar Mahadev Lad <prabhakar.mahadev-lad.rj@bp.renesas.com>
> > > > > Subject: [PATCH v3 5/5] pinctrl: renesas: pinctrl-rzg2l: Add IRQ
> > > > > domain to handle GPIO interrupt
> > > > >
> > > > > Add IRQ domian to RZ/G2L pinctrl driver to handle GPIO interrupt.
> > > > >
> > > > > GPIO0-GPIO122 pins can be used as IRQ lines but only 32 pins can
> > > > > be used as IRQ lines at given time. Selection of pins as IRQ lines
> > > > > is handled by IA55 (which is the IRQC block) which sits in between
> > > > > the
> > > GPIO and GIC.
> > > >
> > > > Do we need to update bindings with interrupt-cells on [1] like [2]
> > > > as it
> > > act as parent for GPIO interrupts?
> > > >
> > > Yes interrupt-controller and interrupt-parent needs to be added. I'm
> > > wondering if "interrupt-cells" is not required. If the pin is an
> > > interrupt it will be passed as an GPIO.
> >
> > It is same as external interrupt case right?
> >
> > For eg:- Ethernet PHY case,
> >
> > interrupt-parent = <&irqc>;
> > interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
> >
> > if you use GPIO, it will be like this right?
> >
> > interrupt-parent = <&pinctrl>;
> > interrupts = <RZG2L_GPIO(1, 0) IRQ_TYPE_LEVEL_LOW>;
>
> FYI,
>
> Previously, I have tested ADV HPD interrupt with below changes while investigating [1]
>
> interrupt-parent = <&pinctrl>;
> interrupts = <RZG2L_GPIO(2, 1) IRQ_TYPE_EDGE_FALLING>;
>
Right, #interrupt-cells=<2> , where the first cell is the GPIO pin and
the second cell is the flag.

Cheers,
Prabhakar

\
 
 \ /
  Last update: 2022-05-13 15:52    [W:0.093 / U:0.392 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site