lkml.org 
[lkml]   [2022]   [May]   [11]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: RFC: Memory Tiering Kernel Interfaces
On Tue, May 10, 2022 at 5:10 AM Aneesh Kumar K V
<aneesh.kumar@linux.ibm.com> wrote:
>
> On 5/10/22 3:29 PM, Hesham Almatary wrote:
> > Hello Yang,
> >
> > On 5/10/2022 4:24 AM, Yang Shi wrote:
> >> On Mon, May 9, 2022 at 7:32 AM Hesham Almatary
> >> <hesham.almatary@huawei.com> wrote:
>
>
> ...
>
> >>>
> >>> node 0 has a CPU and DDR memory in tier 0, node 1 has GPU and DDR memory
> >>> in tier 0,
> >>> node 2 has NVMM memory in tier 1, node 3 has some sort of bigger memory
> >>> (could be a bigger DDR or something) in tier 2. The distances are as
> >>> follows:
> >>>
> >>> -------------- --------------
> >>> | Node 0 | | Node 1 |
> >>> | ------- | | ------- |
> >>> | | DDR | | | | DDR | |
> >>> | ------- | | ------- |
> >>> | | | |
> >>> -------------- --------------
> >>> | 20 | 120 |
> >>> v v |
> >>> ---------------------------- |
> >>> | Node 2 PMEM | | 100
> >>> ---------------------------- |
> >>> | 100 |
> >>> v v
> >>> --------------------------------------
> >>> | Node 3 Large mem |
> >>> --------------------------------------
> >>>
> >>> node distances:
> >>> node 0 1 2 3
> >>> 0 10 20 20 120
> >>> 1 20 10 120 100
> >>> 2 20 120 10 100
> >>> 3 120 100 100 10
> >>>
> >>> /sys/devices/system/node/memory_tiers
> >>> 0-1
> >>> 2
> >>> 3
> >>>
> >>> N_TOPTIER_MEMORY: 0-1
> >>>
> >>>
> >>> In this case, we want to be able to "skip" the demotion path from Node 1
> >>> to Node 2,
> >>>
> >>> and make demotion go directely to Node 3 as it is closer, distance wise.
> >>> How can
> >>>
> >>> we accommodate this scenario (or at least not rule it out as future
> >>> work) with the
> >>>
> >>> current RFC?
> >> If I remember correctly NUMA distance is hardcoded in SLIT by the
> >> firmware, it is supposed to reflect the latency. So I suppose it is
> >> the firmware's responsibility to have correct information. And the RFC
> >> assumes higher tier memory has better performance than lower tier
> >> memory (latency, bandwidth, throughput, etc), so it sounds like a
> >> buggy firmware to have lower tier memory with shorter distance than
> >> higher tier memory IMHO.
> >
> > You are correct if you're assuming the topology is all hierarchically
> >
> > symmetric, but unfortuantely, in real hardware (e.g., my example above)
> >
> > it is not. The distance/latency between two nodes in the same tier
> >
> > and a third node, is different. The firmware still provides the correct
> >
> > latency, but putting a node in a tier is up to the kernel/user, and
> >
> > is relative: e.g., Node 3 could belong to tier 1 from Node 1's
> >
> > perspective, but to tier 2 from Node 0's.
> >
> >
> > A more detailed example (building on my previous one) is when having
> >
> > the GPU connected to a switch:
> >
> > ----------------------------
> > | Node 2 PMEM |
> > ----------------------------
> > ^
> > |
> > -------------- --------------
> > | Node 0 | | Node 1 |
> > | ------- | | ------- |
> > | | DDR | | | | DDR | |
> > | ------- | | ------- |
> > | CPU | | GPU |
> > -------------- --------------
> > | |
> > v v
> > ----------------------------
> > | Switch |
> > ----------------------------
> > |
> > v
> > --------------------------------------
> > | Node 3 Large mem |
> > --------------------------------------
> >
> > Here, demoting from Node 1 to Node 3 directly would be faster as
> >
> > it only has to go through one hub, compared to demoting from Node 1
> >
> > to Node 2, where it goes through two hubs. I hope that example
> >
> > clarifies things a little bit.
> >
>
> Alistair mentioned that we want to consider GPU memory to be expensive
> and want to demote from GPU to regular DRAM. In that case for the above
> case we should end up with
>
>
> tier 0 - > Node3
> tier 1 -> Node0, Node1
> tier 2 -> Node2
>
> Hence
>
> node 0: allowed=2
> node 1: allowed=2
> node 2: allowed = empty
> node 3: allowed = 0-1 , based on fallback order 1, 0

If we have 3 tiers as defined above, then we'd better to have:

node 0: allowed = 2
node 1: allowed = 2
node 2: allowed = empty
node 3: allowed = 0-2, based on fallback order: 1,0,2

The firmware should provide the node distance values to reflect that
PMEM is slowest and should have the largest distance away from node 3.

> -aneesh
>
>

\
 
 \ /
  Last update: 2022-05-11 07:43    [W:0.097 / U:1.556 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site