lkml.org 
[lkml]   [2022]   [Apr]   [6]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v9 1/3] dt-bindings: mmc: mtk-sd: extend interrupts and pinctrls properties
From
Date
On Fri, 2022-04-01 at 12:43 -0500, Rob Herring wrote:
> On Fri, Apr 01, 2022 at 11:22:13AM +0200, Ulf Hansson wrote:
> > On Tue, 29 Mar 2022 at 05:29, Axe Yang <axe.yang@mediatek.com>
> > wrote:
> > >
> > > Extend interrupts and pinctrls for SDIO wakeup interrupt feature.
> > > This feature allow SDIO devices alarm asynchronous interrupt to
> > > host
> > > even when host stop providing clock to SDIO card. An extra wakeup
> > > interrupt and pinctrl states for SDIO DAT1 pin state switching
> > > are
> > > required in this scenario.
> > >
> > > Signed-off-by: Axe Yang <axe.yang@mediatek.com>
> > > ---
> > > .../devicetree/bindings/mmc/mtk-sd.yaml | 17
> > > ++++++++++++++++-
> > > 1 file changed, 16 insertions(+), 1 deletion(-)
> > >
> > > diff --git a/Documentation/devicetree/bindings/mmc/mtk-sd.yaml
> > > b/Documentation/devicetree/bindings/mmc/mtk-sd.yaml
> > > index 297ada03e3de..3872a6ce2867 100644
> > > --- a/Documentation/devicetree/bindings/mmc/mtk-sd.yaml
> > > +++ b/Documentation/devicetree/bindings/mmc/mtk-sd.yaml
> > > @@ -69,12 +69,22 @@ properties:
> > > - const: ahb_cg
> > >
> > > interrupts:
> > > - maxItems: 1
> > > + description:
> > > + Should at least contain MSDC GIC interrupt. To support
> > > SDIO in-band wakeup, an extended
> > > + interrupt is required and be configured as wakeup source
> > > irq.
> >
> > If I understand correctly, the extended interrupt (a GPIO irq) may
> > not
> > necessarily share the same interrupt parent as the primary device
> > interrupt.
> >
> > Perhaps it's then better to extend this with "interrupts-extended"
> > instead. See Documentation/devicetree/bindings/interrupt-
> > controller/interrupts.txt.
>
> 'interrupts-extended' is interchangeable with 'interrupts'. For
> schemas,
> use 'interrupts' and the tools take care of supporting both forms.
>

hello Ulf, you are right, the wakeup interrupt(parent is &pio) do not
share same parent as primary interrupt(parent is &gic). And as you
said, I am using "interrupts-extended" to declare the wakeup irq, see
commit message in patch 3/3:
&mmcX {
...
interrupts-extended = <...>,
<&pio xxx IRQ_TYPE_LEVEL_LOW>;
...
pinctrl-names = "default", "state_uhs", "state_eint";
...
pinctrl-2 = <&mmc2_pins_eint>;
...
cap-sdio-irq;
keep-power-in-suspend;
wakeup-source;
...
};

But the wakup interrupt is for SDIO only, in most instances, MSDC is
been used as eMMC/SD card host, they do not need this interrupt. So as
Rob suggested, I think we'd better keep using 'interrupts'. And I will
update the description for 'interrupts', suggest to use 'interrupts-
extended' to declare SDIO wakeup interrupt.

And 'interrupt-names' is a good idea, I will add this property to
document too. Thank you for the advice.

Regards,
Axe


\
 
 \ /
  Last update: 2022-04-06 15:12    [W:0.560 / U:0.036 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site