lkml.org 
[lkml]   [2022]   [Apr]   [30]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
SubjectRe: [RFC PATCH 18/18] Documentation: add document for pte_ref
From


On 2022/4/30 9:19 PM, Bagas Sanjaya wrote:
> Hi Qi,
>
> On Fri, Apr 29, 2022 at 09:35:52PM +0800, Qi Zheng wrote:
>> +Now in order to pursue high performance, applications mostly use some
>> +high-performance user-mode memory allocators, such as jemalloc or tcmalloc.
>> +These memory allocators use madvise(MADV_DONTNEED or MADV_FREE) to release
>> +physical memory for the following reasons::
>> +
>> + First of all, we should hold as few write locks of mmap_lock as possible,
>> + since the mmap_lock semaphore has long been a contention point in the
>> + memory management subsystem. The mmap()/munmap() hold the write lock, and
>> + the madvise(MADV_DONTNEED or MADV_FREE) hold the read lock, so using
>> + madvise() instead of munmap() to released physical memory can reduce the
>> + competition of the mmap_lock.
>> +
>> + Secondly, after using madvise() to release physical memory, there is no
>> + need to build vma and allocate page tables again when accessing the same
>> + virtual address again, which can also save some time.
>> +
>
> I think we can use enumerated list, like below:

Thanks for your review, LGTM, will do.

>
> -- >8 --
>
> diff --git a/Documentation/vm/pte_ref.rst b/Documentation/vm/pte_ref.rst
> index 0ac1e5a408d7c6..67b18e74fcb367 100644
> --- a/Documentation/vm/pte_ref.rst
> +++ b/Documentation/vm/pte_ref.rst
> @@ -10,18 +10,18 @@ Preface
> Now in order to pursue high performance, applications mostly use some
> high-performance user-mode memory allocators, such as jemalloc or tcmalloc.
> These memory allocators use madvise(MADV_DONTNEED or MADV_FREE) to release
> -physical memory for the following reasons::
> -
> - First of all, we should hold as few write locks of mmap_lock as possible,
> - since the mmap_lock semaphore has long been a contention point in the
> - memory management subsystem. The mmap()/munmap() hold the write lock, and
> - the madvise(MADV_DONTNEED or MADV_FREE) hold the read lock, so using
> - madvise() instead of munmap() to released physical memory can reduce the
> - competition of the mmap_lock.
> -
> - Secondly, after using madvise() to release physical memory, there is no
> - need to build vma and allocate page tables again when accessing the same
> - virtual address again, which can also save some time.
> +physical memory for the following reasons:
> +
> +1. We should hold as few write locks of mmap_lock as possible,
> + since the mmap_lock semaphore has long been a contention point in the
> + memory management subsystem. The mmap()/munmap() hold the write lock, and
> + the madvise(MADV_DONTNEED or MADV_FREE) hold the read lock, so using
> + madvise() instead of munmap() to released physical memory can reduce the
> + competition of the mmap_lock.
> +
> +2. After using madvise() to release physical memory, there is no
> + need to build vma and allocate page tables again when accessing the same
> + virtual address again, which can also save some time.
>
> The following is the largest user PTE page table memory that can be
> allocated by a single user process in a 32-bit and a 64-bit system.
>
>> +The following is the largest user PTE page table memory that can be
>> +allocated by a single user process in a 32-bit and a 64-bit system.
>> +
>
> We can say "assuming 4K page size" here,
>
>> ++---------------------------+--------+---------+
>> +| | 32-bit | 64-bit |
>> ++===========================+========+=========+
>> +| user PTE page table pages | 3 MiB | 512 GiB |
>> ++---------------------------+--------+---------+
>> +| user PMD page table pages | 3 KiB | 1 GiB |
>> ++---------------------------+--------+---------+
>> +
>> +(for 32-bit, take 3G user address space, 4K page size as an example;
>> + for 64-bit, take 48-bit address width, 4K page size as an example.)
>> +
>
> ... instead of here.

will do.

>
>> +There is also a lock-less scenario(such as fast GUP). Fortunately, we don't need
>> +to do any additional operations to ensure that the system is in order. Take fast
>> +GUP as an example::
>> +
>> + thread A thread B
>> + fast GUP madvise(MADV_DONTNEED)
>> + ======== ======================
>> +
>> + get_user_pages_fast_only()
>> + --> local_irq_save();
>> + call_rcu(pte_free_rcu)
>> + gup_pgd_range();
>> + local_irq_restore();
>> + /* do pte_free_rcu() */
>> +
>
> I see whitespace warning circa do pte_free_rcu() line above when
> applying this series.

will fix.

Thanks,
Qi

>
> Thanks.
>

--
Thanks,
Qi

\
 
 \ /
  Last update: 2022-04-30 15:33    [W:0.086 / U:0.012 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site