lkml.org 
[lkml]   [2022]   [Apr]   [19]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH 1/3] SPI: Ingenic: Add support for use GPIO as chip select line.
From
Date
Hi Paul,

On 2022/4/20 上午1:13, Paul Cercueil wrote:
> Hi Zhou,
>
> Le ven., avril 15 2022 at 22:22:06 +0800, 周琰杰 (Zhou Yanjie)
> <zhouyanjie@wanyeetech.com> a écrit :
>> Add support for using GPIOs as chip select lines on Ingenic SoCs.
>>
>> Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
>> ---
>>  drivers/spi/spi-ingenic.c | 11 +++++++++--
>>  1 file changed, 9 insertions(+), 2 deletions(-)
>>
>> diff --git a/drivers/spi/spi-ingenic.c b/drivers/spi/spi-ingenic.c
>> index 03077a7..672e4ed 100644
>> --- a/drivers/spi/spi-ingenic.c
>> +++ b/drivers/spi/spi-ingenic.c
>> @@ -380,7 +380,7 @@ static int spi_ingenic_probe(struct
>> platform_device *pdev)
>>      struct spi_controller *ctlr;
>>      struct ingenic_spi *priv;
>>      void __iomem *base;
>> -    int ret;
>> +    int num_cs, ret;
>>
>>      pdata = of_device_get_match_data(dev);
>>      if (!pdata) {
>> @@ -416,6 +416,11 @@ static int spi_ingenic_probe(struct
>> platform_device *pdev)
>>      if (IS_ERR(priv->flen_field))
>>          return PTR_ERR(priv->flen_field);
>>
>> +    if (of_property_read_u32(dev->of_node, "num-cs", &num_cs)) {
>
> One small comment here - I think it would be better to use
> device_property_read_u32().
>
> The driver should also use device_get_match_data() instead of
> of_device_get_match_data(), but that's a cleanup that can be done later.
>

Sure, I will send v2.


Thanks and best regards!


> Cheers,
> -Paul
>
>> +        dev_warn(dev, "Number of chip select lines not specified.\n");
>> +        num_cs = 2;
>> +    }
>> +
>>      platform_set_drvdata(pdev, ctlr);
>>
>>      ctlr->prepare_transfer_hardware = spi_ingenic_prepare_hardware;
>> @@ -429,7 +434,9 @@ static int spi_ingenic_probe(struct
>> platform_device *pdev)
>>      ctlr->bits_per_word_mask = pdata->bits_per_word_mask;
>>      ctlr->min_speed_hz = 7200;
>>      ctlr->max_speed_hz = 54000000;
>> -    ctlr->num_chipselect = 2;
>> +    ctlr->use_gpio_descriptors = true;
>> +    ctlr->max_native_cs = 2;
>> +    ctlr->num_chipselect = num_cs;
>>      ctlr->dev.of_node = pdev->dev.of_node;
>>
>>      if (spi_ingenic_request_dma(ctlr, dev))
>> --
>> 2.7.4
>>
>

\
 
 \ /
  Last update: 2022-04-19 19:31    [W:0.098 / U:0.516 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site